Chemical mechanical planarization of Ge 2 Sb 2 Te 5 using IC1010 and Politex reg pads in acidic slurry
Authors:
- Ao-Dong HeAHAo-Dong He
- Bo LiuBLBo Liu
- Zhi-Tang SongZSZhi-Tang Song
- Liang-Yong WangLWLiang-Yong Wang
- Wei-Li LiuWLWei-Li Liu
- Gao-Ming FengGFGao-Ming Feng
- Song-Lin FengSFSong-Lin Feng
- 31 July 2014
- journal article
- Published by IOP Publishing in Chinese Physics B
- Vol. 23 (8) , 088502
Abstract
In the paper, chemical mechanical planarization (CMP) of Ge2Sb2Te5 (GST) is investigated using IC1010 and Politex reg pads in acidic slurry. For the CMP with blank wafer, it is found that the removal rate (RR) of GST increases with the increase of pressure for both pads, but the RR of GST polished using IC1010 is far more than that of Politex reg. To check the surface defects, GST film is observed with an optical microscope (OM) and scanning electron microscope (SEM). For the CMP with Politex reg, many spots are observed on the surface of the blank wafer with OM, but no obvious spots are observed with SEM. With regard to the patterned wafer, a few stains are observed on the GST cell, but many residues are found on other area with OM. However, from SEM results, a few residues are observed on the GST cell, more dielectric loss is revealed about the trench structure. For the CMP with IC1010, the surface of the polished blank wafer suffers serious scratches found with both OM and SEM, which may result from a low hardness of GST, compared with those of IC1010 and abrasives. With regard to the patterned wafer, it can achieve a clean surface and almost no scratches are observed with OM, which may result from the high-hardness SiO2 film on the surface, not from the soft GST film across the whole wafer. From the SEM results, a clean interface and no residues are observed on the GST surface, and less dielectric loss is revealed. Compared with Politex reg, the patterned wafer can achieve a good performance after CMP using IC1010.Keywords
This publication has 17 references indexed in Scilit:
- Mechanism of amorphous Ge2Sb2Te5removal during chemical mechanical planarization in acidic H2O2slurryChinese Physics B, 2013
- Research and Development of Chemical Mechanical Planarization for Ge2Sb2Te5Acta Chimica Sinica, 2013
- Mechanism of Ge2Sb2Te5 chemical mechanical polishingApplied Surface Science, 2012
- Amorphous Ge2Sb2Te5Chemical Mechanical Planarization Using (NH4)2S2O8or H2O2as Oxidizer in Acidic SlurryECS Journal of Solid State Science and Technology, 2012
- Effect of Slurry pH and H2O2on Polycrystalline Ge2Sb2Te5CMP PerformanceJournal of the Electrochemical Society, 2012
- Effect of Nonionic Polymer as Corrosion Inhibitor in Alkaline Media for Polycrystalline Ge2Sb2Te5 Chemical Mechanical PlanarizationElectrochemical and Solid-State Letters, 2011
- Damascene Array Structure of Phase Change Memory Fabricated with Chemical Mechanical Polishing MethodChinese Physics Letters, 2006
- Ge2Sb2Te5 Confined Structures and Integration of 64 Mb Phase-Change Random Access MemoryJapanese Journal of Applied Physics, 2005
- Understanding the phase-change mechanism of rewritable optical mediaNature Materials, 2004
- Rewritable phase-change optical recording in Ge2Sb2Te5 films induced by picosecond laser pulsesApplied Physics Letters, 2004