Adsorption Combined with Electrocoagulation Process for Ketoprofen Removal from Aqueous Solution: Optimization Using Central Composite Design
Authors:
- Katia Madi-AzegaghKMKatia Madi-Azegagh
- Idris YahiaouiIdris Yahiaoui
- Rima ArfiRARima Arfi
- Lydia BenkerrouLBLydia Benkerrou
- Lamia KhennicheLKLamia Khenniche
- Hafida LebikHLHafida Lebik
- Amine Aymen AssadiAmine Aymen Assadi
- Lotfi KhezamiLKLotfi Khezami
- Karim KriaaKarim Kriaa
- Farida Aissani-BenissadFAFarida Aissani-Benissad
Open Access
Abstract
The combination of electrocoagulation (EC) with complementary treatment methods has garnered increasing attention for wastewater remediation. This study aims to design and optimize a hybrid electrocoagulation–adsorption (EC/Ads) process for the removal of ketoprofen (KTP) from aqueous solutions. The adsorption of KTP onto activated carbon (AC) alone exhibited a low removal efficiency of approximately 27% under the following conditions: initial KTP concentration ([KTP]0) = 23 mg·L−1, pH = 6, adsorbent dose (qAC) = 0.5 g, and contact time = 30 min. In contrast, the EC process alone achieved a removal efficiency of 59.69% under similar conditions (current density (i) = 18.6 mA·cm−2, NaCl = 3.5 g·L−1). The combined EC/Ads process significantly enhanced KTP removal, reaching 87.11% under the same operational parameters. The synergistic effect of the combined treatment was quantified with a synergy index of 1.37. Characterization techniques included FTIR analysis of both AC and KTP, as well as adsorption–desorption isotherms and pHPZC determination for AC. To further optimize the EC/Ads process, a response surface methodology based on central composite design (CCD) was applied to assess the influence of four independent variables: pH, [KTP]0, current density, and qAC. Optimal conditions were identified as follows: qAC = 0.63–0.99 g, i = 12.32–14.68 mA·cm−2, pH = 6.5, and [KTP]0 = 22.5 mg·L−1; these conditions resulted in 100% KTP removal after 30 min of treatment. These findings demonstrate the potential of the EC/Ads hybrid process to be an efficient and sustainable alternative for pharmaceutical contaminant removal.Keywords
Funding Information
- Imam Mohammad Ibn Saud Islamic University (IMSIU) (IMSIU-DDRSP2502)
This publication has 31 references indexed in Scilit:
- Degradation of paracetamol by sulfate radicals using UVA-irradiation/heat activated peroxydisulfate: kinetics and optimization using Box–Behnken designReaction Kinetics, Mechanisms and Catalysis, 2023
- A review of the toxicology presence and removal of ketoprofen through adsorption technologyJournal of Environmental Chemical Engineering, 2022
- Removal of drug losartan in environmental aquatic matrices by heat-activated persulfate: Kinetics, transformation products and synergistic effectsChemosphere, 2022
- Combination of electrocoagulation and adsorption processes to remove methyl orange from aqueous solutionEnvironmental Technology & Innovation, 2021
- Central composite design (CCD)-Response surface methodology (RSM) of effective electrospinning parameters on PVP-B-Hf hybrid nanofibrous composites for synthesis of HfB2-based composite nanofibersComposites Part B: Engineering, 2019
- Response surface methodology application in optimization of cadmium adsorption by shoe waste: A good option of waste mitigation by wasteEcological Engineering, 2016
- Conventional methods and emerging wastewater polishing technologies for palm oil mill effluent treatment: A reviewJournal of Environmental Management, 2015
- The use and importance of design of experiments ( DOE ) in process modelling in food science and technology2013
- Removal of pharmaceuticals during wastewater treatment and environmental risk assessment using hazard indexesEnvironment International, 2010
- Preparation and characterization of activated carbons from impregnation pitch by ZnCl2Applied Surface Science, 2006