Lydia Benkerrou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Lydia Benkerrou has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Aymen Amine Assadi
College of Engineering, Imam Mohammad Ibn Saud Islamic University (IMSIU), Riyadh 11432, Saudi Arabia
1 shared publication - Farida Aissani-Benissad
Laboratoire de Génie de l’Environnement (LGE), Faculté de Technologie, Université de Bejaia, Bejaia 06000, Algeria
1 shared publication - Hafida Lebik
Centre de Développement des Energies Renouvelables, CDER, Unité de Développement des Equipements Solaires, UDES, Tipaza 42004, Algeria
1 shared publication - Idris Yahiaoui
Laboratoire de Génie de l’Environnement (LGE), Faculté de Technologie, Université de Bejaia, Bejaia 06000, Algeria
1 shared publication - Karim Kriaa
Department of Chemical Engineering, College of Engineering, Imam Mohammad Ibn Saud Islamic University (IMSIU), Riyadh 11432, Saudi Arabia
1 shared publication - Katia Madi
Laboratoire de Génie de l’Environnement (LGE), Faculté de Technologie, Université de Bejaia, Bejaia 06000, Algeria
1 shared publication
Latest Publications
- Open Access
Adsorption Combined with Electrocoagulation Process for Ketoprofen Removal from Aqueous Solution: Optimization Using Central Composite Design
The combination of electrocoagulation (EC) with complementary treatment methods has garnered increasing attention for wastewater remediation. This study aims to design and optimize a hybrid electrocoagulation–adsorption (EC/Ads) process for the removal of ketoprofen (KTP) from aqueous solutions. The adsorption of KTP onto activated carbon (AC) alone exhibited a low removal efficiency of approximately 27% under the following conditions: initial KTP concentration ([KTP]0) = 23 mg·L−1, pH = 6, adsorbent dose (qAC) = 0.5 g, and contact time = 30 min. In contrast, the EC process alone achieved a removal efficiency of 59.69% under similar conditions (current density (i) = 18.6 mA·cm−2, NaCl = 3.5 g·L−1). The combined EC/Ads process significantly enhanced KTP removal, reaching 87.11% under the same operational parameters. The synergistic effect of the combined treatment was quantified with a synergy index of 1.37. Characterization techniques included FTIR analysis of both AC and KTP, as well as adsorption–desorption isotherms and pHPZC determination for AC. To further optimize the EC/Ads process, a response surface methodology based on central composite design (CCD) was applied to assess the influence of four independent variables: pH, [KTP]0, current density, and qAC. Optimal conditions were identified as follows: qAC = 0.63–0.99 g, i = 12.32–14.68 mA·cm−2, pH = 6.5, and [KTP]0 = 22.5 mg·L−1; these conditions resulted in 100% KTP removal after 30 min of treatment. These findings demonstrate the potential of the EC/Ads hybrid process to be an efficient and sustainable alternative for pharmaceutical contaminant removal.
Open AccessAdsorption Combined with Electrocoagulation Process for Ketoprofen Removal from Aqueous Solution: Optimization Using Central Composite Design
The combination of electrocoagulation (EC) with complementary treatment methods has garnered increasing attention for wastewater remediation. This study aims to design and optimize a hybrid electrocoagulation–adsorption (EC/Ads) process for the removal of ketoprofen (KTP) from aqueous solutions. The adsorption of KTP onto activated carbon (AC) alone exhibited a low removal efficiency of approximately 27% under the following conditions: initial KTP concentration ([KTP]0) = 23 mg·L−1, pH = 6, adsorbent dose (qAC) = 0.5 g, and contact time = 30 min. In contrast, the EC process alone achieved a removal efficiency of 59.69% under similar conditions (current density (i) = 18.6 mA·cm−2, NaCl = 3.5 g·L−1). The combined EC/Ads process significantly enhanced KTP removal, reaching 87.11% under the same operational parameters. The synergistic effect of the combined treatment was quantified with a synergy index of 1.37. Characterization techniques included FTIR analysis of both AC and KTP, as well as adsorption–desorption isotherms and pHPZC determination for AC. To further optimize the EC/Ads process, a response surface methodology based on central composite design (CCD) was applied to assess the influence of four independent variables: pH, [KTP]0, current density, and qAC. Optimal conditions were identified as follows: qAC = 0.63–0.99 g, i = 12.32–14.68 mA·cm−2, pH = 6.5, and [KTP]0 = 22.5 mg·L−1; these conditions resulted in 100% KTP removal after 30 min of treatment. These findings demonstrate the potential of the EC/Ads hybrid process to be an efficient and sustainable alternative for pharmaceutical contaminant removal.