E-beam sintering of neodymium tungstate and its composite with nickel (II) and copper (II) oxides
Authors:
- Nikita F. EremeevNENikita F. Eremeev
- Tamara A. KriegerTKTamara A. Krieger
- Olga A. BulavchenkoOBOlga A. Bulavchenko
- Vasily V. KaichevVKVasily V. Kaichev
- Anna M. KremnevaAKAnna M. Kremneva
- Evgeny A. SuprunESEvgeny A. Suprun
- Mostefe Khalid MohammedMMMostefe Khalid Mohammed
- Mikhail A. MikhailenkoMMMikhail A. Mikhailenko
- Vladislav A. SadykovVladislav A. Sadykov
- Yulia N. BespalkoYBYulia N. Bespalko
Open Access
- 22 September 2026
- journal article
- Published by Ural Federal University in Electrochemical Materials and Technologies
- Vol. 5 (3) , 20254077
Abstract
Neodymium tungstates and their composites with metal alloys, such as NiCu, have emerged as promising materials for hydrogen separation membranes due to their high proton conductivity and stability in CO2-containing atmospheres. The fabrication of gas-tight ceramics based on these materials constitutes a distinct challenge. A promising approach to address this issue is the utilization of advanced sintering techniques, such as radiation-thermal sintering using an electron beam. The present study investigates the impact of radiation-thermal sintering temperature on the structural, textural properties, hydration ability, and oxygen mobility of Nd5.5WO11.25−δ oxides and NiO–CuO–Nd5.5WO11.25−δ composites, the precursors of NiCu alloy – Nd5.5WO11.25−δ materials for hydrogen separation membranes. The main phase of the Nd5.5WO11.25−δ samples is defective double fluorite, while their composites contain various nickel and copper oxides along with the neodymium tungstate phase. The attainment of gas-tightness in Nd5.5WO11.25−δ samples is achieved even at relatively low sintering temperatures (1200–1300 °C), which is unattainable through sintering in a furnace. Conversely, the composite samples exhibit high porosity. Hence, the procedure of preparing the NiO–CuO–Nd5.5WO11.25−δ composites required further optimization. Nd5.5WO11.25−δ sintered by e-beam at 1100–1300 °C exhibit optimal hydration properties. The highest oxygen mobility is demonstrated for the samples sintered at 1100 and 1200 °C (D* up to ~ 10−8 cm2/s), which is promising in the context of the incorporation and transport of protons in hydrogen separation membranes. Consequently, e-beam sintering emerges as a promising method for producing proton conductive ceramics based on Nd tungstate.Keywords
This publication has 154 references indexed in Scilit:
- Emerging Materials and Future Strategies for Solid Oxide Electrochemical CellsAdvanced Energy Materials, 2026
- Current Scenario of Nanocomposite Materials for Fuel Cell Applications2019
- Proton and Protonic Species: The Hidden Face of Solid State Chemistry. How to Measure H‐Content in Materials?Fuel Cells, 2012
- Synthesis, Structure and Electrical Properties of Mo‐doped CeO2–Materials for SOFCsFuel Cells, 2009
- The Isotopic Exchange Reaction of Oxygen on Metal OxidesJournal of Catalysis, 1999
- Physical foundations for high-temperature electron-beam modification of ceramicsRussian Physics Journal, 1996
- Study of the reduction behavior of W/TiO 2 catalysts by XPS using curve fitting, deconvolution and factor analysisSurface and Interface Analysis, 1995
- Electron beam stimulated chemical reaction in solidsJournal of Thermal Analysis and Calorimetry, 1995
- Hydrogen transport in nickel-base alloysMetallurgical Transactions A, 1992
- Diffusion of hydrogen in metals1978