Biomechanical Advantages of Triple‐Loaded Suture Anchors Compared With Double‐Row Rotator Cuff Repairs
Authors:
- 28 December 2009
- journal article
- research article
- Published by Wiley in Arthroscopy
- Vol. 26 (3) , 316-323
Abstract
Purpose: To evaluate the strength and suture‐tendon interface security of various suture anchors triply and doubly loaded with ultrahigh–molecular weight polyethylene–containing sutures and to evaluate the relative effectiveness of placing these anchors in a single‐row or double‐row arrangement by cyclic loading and then destructive testing. Methods: The infraspinatus muscle was reattached to the original humeral footprint by use of 1 of 5 different repair patterns in 40 bovine shoulders. Two single‐row repairs and three double‐row repairs were tested. High‐strength sutures were used for all repairs. Five groups were studied: group 1, 2 triple‐loaded screw suture anchors in a single row with simple stitches; group 2, 2 triple‐loaded screw anchors in a single row with simple stitches over a fourth suture passed perpendicularly (“rip‐stop” stitch); group 3, 2 medial and 2 lateral screw anchors with a single vertical mattress stitch passed from the medial anchors and 2 simple stitches passed from the lateral anchors; group 4, 2 medial double‐loaded screw anchors tied in 2 mattress stitches and 2 push‐in lateral anchors capturing the medial sutures in a “crisscross” spanning stitch; and group 5, 2 medial double‐loaded screw anchors tied in 2 mattress stitches and 2 push‐in lateral anchors creating a “suture‐bridge” stitch. The specimens were cycled between 10 and 180 N at 1.0 Hz for 3,500 cycles or until failure. Endpoints were cyclic loading displacement (5 and 10 mm), total displacement, and ultimate failure load. Results: A single row of triply loaded anchors was more resistant to stretching to a 5‐ and 10‐mm gap than the double‐row repairs with or without the addition of a rip‐stop suture ( P < .05). The addition of a rip‐stop stitch made the repair more resistant to gap formation than a double row repair ( P < .05). The crisscross double row created by 2 medial double‐loaded suture anchors and 2 lateral push‐in anchors stretched more than any other group ( P < .05). Conclusions: Double‐row repairs with either crossing sutures or 4 separate anchor points were more likely to fail (5‐ or 10‐mm gap) than a single‐row repair loaded with 3 simple sutures. Clinical Relevance: The triple‐loaded anchors with ultrahigh–molecular weight polyethylene–containing sutures placed in a single row were more resistant to stretching than the double‐row groups.Keywords
This publication has 34 references indexed in Scilit:
- The Results of Arthroscopic Subscapularis Tendon RepairsArthroscopy, 2008
- Arthroscopic Single‐Row Supraspinatus Tendon Repair With a Modified Mattress Locking Stitch: A Prospective, Randomized Controlled Comparison With a Simple StitchArthroscopy, 2008
- Single‐Row Modified Mason‐Allen Versus Double‐Row Arthroscopic Rotator Cuff Repair: A Biomechanical and Surface Area ComparisonArthroscopy, 2008
- Failure Analysis of Rotator Cuff Repair: A Comparison of Three Double-Row TechniquesJournal of Bone and Joint Surgery, 2008
- The Time for Functional Recovery After Arthroscopic Rotator Cuff Repair: Correlation With Tendon Healing Controlled by Computed Tomography ArthrographyArthroscopy, 2007
- Arthroscopic Repair of Full‐Thickness Tears of the Rotator Cuff in Patients Younger Than 40 YearsArthroscopy, 2007
- The Effect of Double‐Row Fixation on Initial Repair Strength in Rotator Cuff Repair: A Biomechanical StudyArthroscopy, 2006
- Biomechanical Comparison of a Single-Row versus Double-Row Suture Anchor Technique for Rotator Cuff RepairThe American Journal of Sports Medicine, 2006
- Biomechanical Evaluation of Arthroscopic Rotator Cuff RepairsJournal of Bone and Joint Surgery, 2006
- Functional and Structural Outcome After Arthroscopic Full‐Thickness Rotator Cuff Repair: Single‐Row Versus Dual‐Row FixationArthroscopy, 2005