Effects of framework design and layering material on fracture strength of implant‐supported zirconia‐based molar crowns
Authors:
- 12 August 2014
- journal article
- research article
- Published by Wiley in Clinical Oral Implants Research
- Vol. 26 (12) , 1407-1413
Abstract
Objectives: To evaluate the effects of framework design and layering material on the fracture strength of implant‐supported zirconia‐based molar crowns.Material and methods: Sixty‐six titanium abutments (GingiHue Post) were tightened onto dental implants (Implant Lab Analog). These abutment–implant complexes were randomly divided into three groups (n = 22) according to the design of the zirconia framework (Katana), namely, uniform‐thickness (UNI), anatomic (ANA), and supported anatomic (SUP) designs. The specimens in each design group were further divided into two subgroups (n = 11): zirconia‐based all‐ceramic restorations (ZAC group) and zirconia‐based restorations with an indirect composite material (Estenia C&B) layered onto the zirconia framework (ZIC group). All crowns were cemented on implant abutments, after which the specimens were tested for fracture resistance. The data were analyzed with the Kruskal–Wallis test and the Mann–Whitney U‐test with the Bonferroni correction (α = 0.05).Results: The following mean fracture strength values (kN) were obtained in UNI design, ANA design, and SUP design, respectively: Group ZAC, 3.78, 6.01, 6.50 and Group ZIC, 3.15, 5.65, 5.83. In both the ZAC and ZIC groups, fracture strength was significantly lower for the UNI design than the other two framework designs (P = 0.001). Fracture strength did not significantly differ (P > 0.420) between identical framework designs in the ZAC and ZIC groups.Conclusions: A framework design with standardized layer thickness and adequate support of veneer by zirconia frameworks, as in the ANA and SUP designs, increases fracture resistance in implant‐supported zirconia‐based restorations under conditions of chewing attrition. Indirect composite material and porcelain perform similarly as layering materials on zirconia frameworks.Keywords
Funding Information
- Japan Society for the Promotion of Science London (24592933)
- School of Dentistry, Nihon University
This publication has 25 references indexed in Scilit:
- Effect of Core Thickness Differences on Post‐Fatigue Indentation Fracture Resistance of Veneered Zirconia CrownsJournal of Prosthodontics, 2013
- Durability of bond between an indirect composite veneering material and zirconium dioxide ceramicsActa Odontologica Scandinavica, 2012
- Effect of veneering technique on the fracture resistance of zirconia fixed dental prosthesesJournal of Oral Rehabilitation, 2012
- Influence of Low‐Temperature Environmental Exposure on the Mechanical Properties and Structural Stability of Dental ZirconiaJournal of Prosthodontics, 2012
- Fracture strength of yttria‐stabilized tetragonal zirconia polycrystals crowns with different design: an in vitro studyClinical Oral Implants Research, 2011
- The influence of surface modification techniques on the performance of a Y-TZP dental ceramicJournal of Dentistry, 2006
- Threshold of tactile sensitivity perceived with dental endosseous implants and natural teethClinical Oral Implants Research, 1995
- The relationship between maximal bite force, bite force endurance, and facial morphology during growth: A cross-sectional studyActa Odontologica Scandinavica, 1993
- Mechanical properties and short‐term in vivo evaluation of yttrium‐oxide‐partially‐stabilized zirconiaJournal of Biomedical Materials Research, 1989
- Masticatory function—a review of the literatureJournal of Oral Rehabilitation, 1975