Charpy impact testing of direct metal laser sintering of AlSi10Mg alloy: process parameters and microstructural investigation
Open Access
- 22 May 2026
- journal article
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (10) , 106508
Abstract
This study investigates the effect of manufacturing parameters on the impact behavior of Charpy test specimens produced from AlSi10Mg alloy using laser powder bed fusion (LPBF) process. For this purpose, specimens were produced using two layer thicknesses (30 µ m and 60 µ m), two infill patterns (grid and rectilinear), and three scanning angles (0°, 45°, and 90°). The effects of these parameters on impact toughness were experimentally evaluated. V-notched Charpy impact tests were performed, and the absorbed fracture energy (J) and fracture angle (°) were determined. Fracture surfaces were further examined with scanning electron microscopy (SEM) to evaluate pore morphology, dimple formation, and fusion quality. The results show that absorbed fracture energy decreases as the scan angle increases. Ductile fracture was predominantly observed at 0°, while brittle fracture behavior became dominant at 45° and 90°. Increasing layer thickness reduced interlayer bonding quality, leading to lack-of-fusion defects. Accordingly, the 30 µ m specimens generally exhibited a denser microstructure and higher absorbed energy (∼9 J). The grid ( G ) infill pattern provided more stable energy absorption compared to the rectilinear ( R ) pattern. SEM observations clearly demonstrated the effect of processing parameters. In particular, the 30 µ m specimens with rectilinear infill, exhibited homogeneous melt pools and distinct dimple formation, indicating ductile fracture. In contrast, the 60 µ m specimens showed larger pores, interlayer fusion defects, and directional tearing characteristics. At a scan angle of 90°, fracture surfaces exhibited a more multidirectional character, while at 0° crack propagation was predominantly uniaxial. The highest impact toughness was obtained for the 30- G -0 condition (∼9 J), and the lowest for the 30- R -90 condition (∼5 J). The findings indicate that LPBF processing parameters have a decisive effect on the impact strength and fracture morphology of AlSi10Mg alloy. These results provide insight into parameter optimization and a better understanding of microstructure mechanical property relationships in components manufactured with LPBF.Keywords
This publication has 40 references indexed in Scilit:
- Fatigue Behavior of Additively Manufactured AlSi10Mg Alloy Under Extreme Environment for Space ApplicationsJournal of Materials Engineering and Performance, 2025
- Recent Progress in the Development of Aluminum Alloys to Prevent Defects in Additive ManufacturingJOM, 2025
- Additive layer-by-layer simulation and process parameter optimization for dynamic performance by additive manufacturing using selective laser melting (AM-SLM) of AlSi10Mg alloyThe International Journal of Advanced Manufacturing Technology, 2025
- Progress in additive manufacturing of nickel‐based superalloys: materials, processing, microstructures, properties and alloy designRare Metals, 2025
- Titanium alloys for biomedical applications: a review on additive manufacturing process and surface modification technologyThe International Journal of Advanced Manufacturing Technology, 2025
- Recent advances in the AlSi10Mg materials fabrication by selective laser melting: process parameters, optimization, low-velocity and ballistic impact responsesProgress in Additive Manufacturing, 2024
- High-Rate Characterization of L-PBF AlSi10Mg under Impact ConditionsJournal of Dynamic Behavior of Materials, 2024
- Influence of post-heat treatment on microstructure, texture, and mechanical properties of 18Ni-300 maraging steel fabricated by using LPBF techniqueProgress in Additive Manufacturing, 2023
- Additive manufacturing of metalsActa Materialia, 2016
- Microstructure and Mechanical Properties of AlSi10Mg Parts Produced by the Laser Beam Additive Manufacturing (AM) TechnologyMetallography, Microstructure, and Analysis, 2014