Mehmet Emin Çetin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mehmet Emin Çetin has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Meram
KTO Karatay University
3 shared publications - Hasan Sofuoglu
Department of Mechanical Engineering, Karadeniz Technical University, Trabzon, Turkey
3 shared publications Ahmet Meram
Department of Mechatronics Engineering , Faculty of Engineering and Natural Sciences , KTO Karatay University , Konya , Türkiye
2 shared publicationsHasan Sofuoglu
2 shared publications- Hasan Ulus
Selcuk University
2 shared publications - Muhammed Yasin Peker
Faculty of Engineering and Architecture, Aeronautical Engineering Department Eskisehir Osmangazi University Eskisehir Turkey
2 shared publications
Latest Publications
- 26 October 2026
- Published by Walter de Gruyter GmbH in Materials Testing
Effect of boron nitride nanoplatelet loading on the thermomechanical performance, thermal stability and X-band electromagnetic interference shielding of carbon-fiber/epoxy laminates
Woven carbon-fiber/epoxy laminates containing 0, 0.5, and 2 wt.% boron nitride nanoplatelets (BNNPs), relative to the epoxy resin mass, were fabricated using the same processing route. Their thermomechanical behavior, thermal stability, and X-band electromagnetic interference (EMI) shielding were evaluated using dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and shielding effectiveness (SE) measurements over 8–12 GHz. At 0.5 wt.% BNNP, the glassy storage modulus ( E ′) increased from 9.3 to 11.2 GPa, and the rubbery plateau modulus increased from 0.33 to 2.1 GPa. The loss factor (tan δ) peak temperature shifted from 95.84 to 105.23 °C, while the temperature at 5 % mass loss (Td5) increased from 305.95 to 314.04 °C. The residual mass at 900 °C increased from 68.53 % for the neat laminate to 72.38–72.93 % for the BNNP-containing laminates. The band-averaged total SE values were approximately 50, 46, and 43 dB for the laminates containing 0, 0.5, and 2 wt.% BNNP, respectively. Although the SE curves crossed at several frequencies, the band-averaged values decreased with increasing BNNP content. Among the formulations tested, the 0.5 wt.% BNNP laminate showed the most favorable thermomechanical response, with a reduction in band-averaged EMI shielding relative to the neat laminate.
- 26 October 2026
- Published by Walter de Gruyter GmbH in Materials Testing
Effect of boron nitride nanoplatelet loading on the thermomechanical performance, thermal stability and X-band electromagnetic interference shielding of carbon-fiber/epoxy laminates
Woven carbon-fiber/epoxy laminates containing 0, 0.5, and 2 wt.% boron nitride nanoplatelets (BNNPs), relative to the epoxy resin mass, were fabricated using the same processing route. Their thermomechanical behavior, thermal stability, and X-band electromagnetic interference (EMI) shielding were evaluated using dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and shielding effectiveness (SE) measurements over 8–12 GHz. At 0.5 wt.% BNNP, the glassy storage modulus ( E ′) increased from 9.3 to 11.2 GPa, and the rubbery plateau modulus increased from 0.33 to 2.1 GPa. The loss factor (tan δ) peak temperature shifted from 95.84 to 105.23 °C, while the temperature at 5 % mass loss (Td5) increased from 305.95 to 314.04 °C. The residual mass at 900 °C increased from 68.53 % for the neat laminate to 72.38–72.93 % for the BNNP-containing laminates. The band-averaged total SE values were approximately 50, 46, and 43 dB for the laminates containing 0, 0.5, and 2 wt.% BNNP, respectively. Although the SE curves crossed at several frequencies, the band-averaged values decreased with increasing BNNP content. Among the formulations tested, the 0.5 wt.% BNNP laminate showed the most favorable thermomechanical response, with a reduction in band-averaged EMI shielding relative to the neat laminate.
- Open Access
- 1 October 2026
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 147 (10) , 105008
Influence of screw diameter on the pull-out resistance of additively manufactured auxetic bone screws in cancellous and cortical bone
This study investigates the effect of screw diameter on the pull-out strength of a bone screw with a loosening-resistant auxetic structure manufactured using additive manufacturing. The variation in mechanical performance depending on screw diameter was examined experimentally and through finite element analysis in cancellous and cortical bone structures. First, screw designs with different diameters incorporating an auxetic cell structure were created in SolidWorks. The designed screws were analyzed using ANSYS Workbench finite element software, confirming that the structures exhibit a negative Poisson's ratio (NPR). The screws were manufactured from Ti6Al4V alloy using the direct metal laser sintering additive manufacturing process. The fabricated auxetic screws were inserted into synthetic cancellous and cortical bone (L4-L5 vertebral bone). The pull-out tests were performed under conditions conforming to the ASTM F543 standard. Force-displacement curves were obtained from the experiments, and tensile tests were also conducted to determine the mechanical strength of the screws. To evaluate the performance of the auxetic screws, identical pull-out tests were carried out on conventional bone screws. After the tests, SEM images were obtained to examine the damage mechanisms in detail. The results showed that auxetic bone screws exhibited approximately 4%-15% higher pull-out strength compared to conventional screws. This improvement is attributed to increased surface roughness and radial expansion under tensile loading, which enhance mechanical interlocking at the bone-screw interface. Finite element analyses further indicated that the magnitude of the NPR increased with increasing screw diameter, suggesting more effective mechanical behavior at larger diameters. In addition, the porous structure of the auxetic screw is expected to facilitate bone ingrowth, thereby supporting bone healing and reducing the risk of loosening. Finally, the developed auxetic bone screw has the potential to increase resistance to loosening. In addition, it may enhance biological integration with bone, which could contribute to improved surgical outcomes and greater patient comfort.
- 1 October 2026
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 147 (10) , 105008
Open AccessInfluence of screw diameter on the pull-out resistance of additively manufactured auxetic bone screws in cancellous and cortical bone
This study investigates the effect of screw diameter on the pull-out strength of a bone screw with a loosening-resistant auxetic structure manufactured using additive manufacturing. The variation in mechanical performance depending on screw diameter was examined experimentally and through finite element analysis in cancellous and cortical bone structures. First, screw designs with different diameters incorporating an auxetic cell structure were created in SolidWorks. The designed screws were analyzed using ANSYS Workbench finite element software, confirming that the structures exhibit a negative Poisson's ratio (NPR). The screws were manufactured from Ti6Al4V alloy using the direct metal laser sintering additive manufacturing process. The fabricated auxetic screws were inserted into synthetic cancellous and cortical bone (L4-L5 vertebral bone). The pull-out tests were performed under conditions conforming to the ASTM F543 standard. Force-displacement curves were obtained from the experiments, and tensile tests were also conducted to determine the mechanical strength of the screws. To evaluate the performance of the auxetic screws, identical pull-out tests were carried out on conventional bone screws. After the tests, SEM images were obtained to examine the damage mechanisms in detail. The results showed that auxetic bone screws exhibited approximately 4%-15% higher pull-out strength compared to conventional screws. This improvement is attributed to increased surface roughness and radial expansion under tensile loading, which enhance mechanical interlocking at the bone-screw interface. Finite element analyses further indicated that the magnitude of the NPR increased with increasing screw diameter, suggesting more effective mechanical behavior at larger diameters. In addition, the porous structure of the auxetic screw is expected to facilitate bone ingrowth, thereby supporting bone healing and reducing the risk of loosening. Finally, the developed auxetic bone screw has the potential to increase resistance to loosening. In addition, it may enhance biological integration with bone, which could contribute to improved surgical outcomes and greater patient comfort.
- 2 September 2026
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 14 (3) , 1667-1679
INVESTIGATION OF THE MECHANICAL PROPERTIES OF ADHESIVE MORTARS USED IN CERAMIC-BRICK JOINTS FOR THE RESTORATION OF THE HISTORICAL KUBBE-I HADRA IN THE MEVLANA MUSEUM
In order to perform restoration works, which are widely carried out for the protection of historical heritage, it is necessary to ensure that the structures can withstand various natural conditions. In this study, the mechanical properties of 2 different ridge mounting mortars ceramic tile adhesive mortars, which are frequently used in the market and planned to be used for bonding ceramic tiles on bricks in the restoration of the Kubbe-i Hadra in Konya Mevlana Museum, were investigated. The samples prepared by applying the mounting mortar between the ceramic and brick surfaces were exposed to various conditions in accordance with the standards, and their behavior under harsh conditions was also examined. The conditionings were carried out in 4 different environments to mimic the natural conditions: room temperature, 70°C temperature, water conditioning, and freeze-thaw cycle after water conditioning. The conditioned specimens were subjected to axial tensile tests, and the test data were compared and interpreted together with macro photographs of the fracture surfaces. The results were evaluated, and the usability of both mounting mortars was investigated. According to TS EN 12004-2 standard requirements, both mortars exhibited tensile strengths higher than 0.5 MPa, confirming sufficient bonding performance. Furthermore, the freeze–thaw effect was quantitatively demonstrated through shear test energy values: the absorbed energy decreased from 1.73 J to 0.34 J for H30 (80.3% loss) and from 0.72 J to 0.30 J for MKM (58.3% loss) after freeze–thaw cycling following water conditioning. The findings indicate that the selection of bonding mortars used in restoration works plays a crucial role in the overall performance and durability of the repaired structures. Therefore, choosing an appropriate mortar type can provide important guidance for achieving more reliable and long-lasting restoration applications.
- 2 September 2026
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 14 (3) , 1667-1679
INVESTIGATION OF THE MECHANICAL PROPERTIES OF ADHESIVE MORTARS USED IN CERAMIC-BRICK JOINTS FOR THE RESTORATION OF THE HISTORICAL KUBBE-I HADRA IN THE MEVLANA MUSEUM
In order to perform restoration works, which are widely carried out for the protection of historical heritage, it is necessary to ensure that the structures can withstand various natural conditions. In this study, the mechanical properties of 2 different ridge mounting mortars ceramic tile adhesive mortars, which are frequently used in the market and planned to be used for bonding ceramic tiles on bricks in the restoration of the Kubbe-i Hadra in Konya Mevlana Museum, were investigated. The samples prepared by applying the mounting mortar between the ceramic and brick surfaces were exposed to various conditions in accordance with the standards, and their behavior under harsh conditions was also examined. The conditionings were carried out in 4 different environments to mimic the natural conditions: room temperature, 70°C temperature, water conditioning, and freeze-thaw cycle after water conditioning. The conditioned specimens were subjected to axial tensile tests, and the test data were compared and interpreted together with macro photographs of the fracture surfaces. The results were evaluated, and the usability of both mounting mortars was investigated. According to TS EN 12004-2 standard requirements, both mortars exhibited tensile strengths higher than 0.5 MPa, confirming sufficient bonding performance. Furthermore, the freeze–thaw effect was quantitatively demonstrated through shear test energy values: the absorbed energy decreased from 1.73 J to 0.34 J for H30 (80.3% loss) and from 0.72 J to 0.30 J for MKM (58.3% loss) after freeze–thaw cycling following water conditioning. The findings indicate that the selection of bonding mortars used in restoration works plays a crucial role in the overall performance and durability of the repaired structures. Therefore, choosing an appropriate mortar type can provide important guidance for achieving more reliable and long-lasting restoration applications.
- Top Cited PapersOpen Access
- 21 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (18) , 16193-16211
Recycled Polyacrylonitrile Nanofiber Interleaves With Graphene Nanoplatelets for Adhesively Bonded Composite Joints: Lap‐Shear and Opening‐Mode Fracture Performance
This study presents a sustainable toughening strategy for adhesively bonded CFRP joints by using electrospun polyacrylonitrile (PAN) nanofiber interleaves produced from virgin PAN (vPAN) and recycled PAN (rPAN) recovered from textile‐waste Orlon. Graphene nanoplatelet (GNP)‐hybridized vPAN and rPAN interleaves were also examined to clarify the combined effect of nanofiber bridging and GNP‐assisted crack resistance. Single‐lap joint tests showed that the lap‐shear strength increased from 10.34 MPa for neat epoxy to 11.80 MPa for vPAN/Ep and 12.40 MPa for rPAN/Ep. The highest strength was obtained for GNP–rPAN/Ep, reaching 13.24 MPa, which corresponds to a 28.08% improvement over neat epoxy. Under Mode‐I DCB loading, the crack‐initiation load increased from 49.39 N for neat epoxy to 77.68 N for GNP–rPAN/Ep, while the critical fracture energy increased from 230.16 to 376.31 J/m 2 . Fracture surface observations indicated that nanofiber interleaving changed the damage response from a more interface‐dominated appearance toward a more heterogeneous mixed‐fracture character. SEM observations further supported the activation of nanofiber bridging, pull‐out, crack‐path deviation, and GNP‐assisted pinning/deflection mechanisms. The results show that rPAN nanofiber interleaves have the potential to improve joint strength and fracture resistance and promote the use of circular materials in composite bonding applications.
- 21 June 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (18) , 16193-16211
Top Cited PapersOpen AccessRecycled Polyacrylonitrile Nanofiber Interleaves With Graphene Nanoplatelets for Adhesively Bonded Composite Joints: Lap‐Shear and Opening‐Mode Fracture Performance
This study presents a sustainable toughening strategy for adhesively bonded CFRP joints by using electrospun polyacrylonitrile (PAN) nanofiber interleaves produced from virgin PAN (vPAN) and recycled PAN (rPAN) recovered from textile‐waste Orlon. Graphene nanoplatelet (GNP)‐hybridized vPAN and rPAN interleaves were also examined to clarify the combined effect of nanofiber bridging and GNP‐assisted crack resistance. Single‐lap joint tests showed that the lap‐shear strength increased from 10.34 MPa for neat epoxy to 11.80 MPa for vPAN/Ep and 12.40 MPa for rPAN/Ep. The highest strength was obtained for GNP–rPAN/Ep, reaching 13.24 MPa, which corresponds to a 28.08% improvement over neat epoxy. Under Mode‐I DCB loading, the crack‐initiation load increased from 49.39 N for neat epoxy to 77.68 N for GNP–rPAN/Ep, while the critical fracture energy increased from 230.16 to 376.31 J/m 2 . Fracture surface observations indicated that nanofiber interleaving changed the damage response from a more interface‐dominated appearance toward a more heterogeneous mixed‐fracture character. SEM observations further supported the activation of nanofiber bridging, pull‐out, crack‐path deviation, and GNP‐assisted pinning/deflection mechanisms. The results show that rPAN nanofiber interleaves have the potential to improve joint strength and fracture resistance and promote the use of circular materials in composite bonding applications.
- Open Access
- 22 May 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (10) , 106508
Charpy impact testing of direct metal laser sintering of AlSi10Mg alloy: process parameters and microstructural investigation
This study investigates the effect of manufacturing parameters on the impact behavior of Charpy test specimens produced from AlSi10Mg alloy using laser powder bed fusion (LPBF) process. For this purpose, specimens were produced using two layer thicknesses (30 µ m and 60 µ m), two infill patterns (grid and rectilinear), and three scanning angles (0°, 45°, and 90°). The effects of these parameters on impact toughness were experimentally evaluated. V-notched Charpy impact tests were performed, and the absorbed fracture energy (J) and fracture angle (°) were determined. Fracture surfaces were further examined with scanning electron microscopy (SEM) to evaluate pore morphology, dimple formation, and fusion quality. The results show that absorbed fracture energy decreases as the scan angle increases. Ductile fracture was predominantly observed at 0°, while brittle fracture behavior became dominant at 45° and 90°. Increasing layer thickness reduced interlayer bonding quality, leading to lack-of-fusion defects. Accordingly, the 30 µ m specimens generally exhibited a denser microstructure and higher absorbed energy (∼9 J). The grid ( G ) infill pattern provided more stable energy absorption compared to the rectilinear ( R ) pattern. SEM observations clearly demonstrated the effect of processing parameters. In particular, the 30 µ m specimens with rectilinear infill, exhibited homogeneous melt pools and distinct dimple formation, indicating ductile fracture. In contrast, the 60 µ m specimens showed larger pores, interlayer fusion defects, and directional tearing characteristics. At a scan angle of 90°, fracture surfaces exhibited a more multidirectional character, while at 0° crack propagation was predominantly uniaxial. The highest impact toughness was obtained for the 30- G -0 condition (∼9 J), and the lowest for the 30- R -90 condition (∼5 J). The findings indicate that LPBF processing parameters have a decisive effect on the impact strength and fracture morphology of AlSi10Mg alloy. These results provide insight into parameter optimization and a better understanding of microstructure mechanical property relationships in components manufactured with LPBF.
- 22 May 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (10) , 106508
Open AccessCharpy impact testing of direct metal laser sintering of AlSi10Mg alloy: process parameters and microstructural investigation
This study investigates the effect of manufacturing parameters on the impact behavior of Charpy test specimens produced from AlSi10Mg alloy using laser powder bed fusion (LPBF) process. For this purpose, specimens were produced using two layer thicknesses (30 µ m and 60 µ m), two infill patterns (grid and rectilinear), and three scanning angles (0°, 45°, and 90°). The effects of these parameters on impact toughness were experimentally evaluated. V-notched Charpy impact tests were performed, and the absorbed fracture energy (J) and fracture angle (°) were determined. Fracture surfaces were further examined with scanning electron microscopy (SEM) to evaluate pore morphology, dimple formation, and fusion quality. The results show that absorbed fracture energy decreases as the scan angle increases. Ductile fracture was predominantly observed at 0°, while brittle fracture behavior became dominant at 45° and 90°. Increasing layer thickness reduced interlayer bonding quality, leading to lack-of-fusion defects. Accordingly, the 30 µ m specimens generally exhibited a denser microstructure and higher absorbed energy (∼9 J). The grid ( G ) infill pattern provided more stable energy absorption compared to the rectilinear ( R ) pattern. SEM observations clearly demonstrated the effect of processing parameters. In particular, the 30 µ m specimens with rectilinear infill, exhibited homogeneous melt pools and distinct dimple formation, indicating ductile fracture. In contrast, the 60 µ m specimens showed larger pores, interlayer fusion defects, and directional tearing characteristics. At a scan angle of 90°, fracture surfaces exhibited a more multidirectional character, while at 0° crack propagation was predominantly uniaxial. The highest impact toughness was obtained for the 30- G -0 condition (∼9 J), and the lowest for the 30- R -90 condition (∼5 J). The findings indicate that LPBF processing parameters have a decisive effect on the impact strength and fracture morphology of AlSi10Mg alloy. These results provide insight into parameter optimization and a better understanding of microstructure mechanical property relationships in components manufactured with LPBF.
- Top Cited PapersOpen Access
Fracture and Fatigue Assessment of Bonded Composite Patch Repairs in Notched and Cracked Plates
This study presents a unified mechanics-based framework for evaluating bonded composite patch repairs. Discrete fracture, fatigue, and adhesive responses are transformed into continuous master equations over the design space. Low-order polynomial surfaces model stress intensity and concentration responses, enabling continuous prediction of repair performance without repeated finite-element analyses. A fracture-based repair efficiency index is derived from the analytical master surface. This index quantifies the average reduction in crack-driving force across the domain. Combined with adhesive stiffness and strength, it defines an adhesive-based repair efficiency index (A-REI), providing a direct link between structural response and material properties. The results show that repair effectiveness is strongly influenced by both geometric severity and adhesive properties. Fatigue performance decreases significantly with increasing notch ratio in single-sided repairs. Double-sided configurations maintain consistently higher efficiency. Symmetric reinforcement more effectively reduces stress concentration, with improvements exceeding 40% at intermediate notch ratios. Adhesive selection is governed by stiffness and strength. Structural adhesives achieve significantly higher A-REI values, whereas compliant adhesives contribute negligibly. Overall, repair symmetry controls the magnitude of improvement, while adhesive properties determine performance ranking. This framework provides a clear, practical basis for design and material selection.
Top Cited PapersOpen AccessFracture and Fatigue Assessment of Bonded Composite Patch Repairs in Notched and Cracked Plates
This study presents a unified mechanics-based framework for evaluating bonded composite patch repairs. Discrete fracture, fatigue, and adhesive responses are transformed into continuous master equations over the design space. Low-order polynomial surfaces model stress intensity and concentration responses, enabling continuous prediction of repair performance without repeated finite-element analyses. A fracture-based repair efficiency index is derived from the analytical master surface. This index quantifies the average reduction in crack-driving force across the domain. Combined with adhesive stiffness and strength, it defines an adhesive-based repair efficiency index (A-REI), providing a direct link between structural response and material properties. The results show that repair effectiveness is strongly influenced by both geometric severity and adhesive properties. Fatigue performance decreases significantly with increasing notch ratio in single-sided repairs. Double-sided configurations maintain consistently higher efficiency. Symmetric reinforcement more effectively reduces stress concentration, with improvements exceeding 40% at intermediate notch ratios. Adhesive selection is governed by stiffness and strength. Structural adhesives achieve significantly higher A-REI values, whereas compliant adhesives contribute negligibly. Overall, repair symmetry controls the magnitude of improvement, while adhesive properties determine performance ranking. This framework provides a clear, practical basis for design and material selection.
- 25 February 2026
- Published by Springer Nature
- p. 447-452
Composite Materials for Space Radiation Shielding: A Review
- 25 February 2026
- Published by Springer Nature
- p. 447-452
Composite Materials for Space Radiation Shielding: A Review
- Open Access
- 30 June 2025
- Published by Selcuk University in International Journal of Aeronautics and Astronautics
- Vol. 6 (1) , 34-43
Analysis of a UAV propeller produced by various materials
Recently, Unmanned Aerial Vehicle (UAV) systems have started to attract great interest worldwide. With the orientation of the technology sector to this field, studies on UAV systems have gained momentum. Propellers, which are an important part of UAV systems, are of great importance to the propulsion system of the aircraft. Deformations that may occur, especially in propellers that are expected to have high strength, greatly affect flight safety. In this study, a two-bladed propeller model measuring 12 inches was created. The deformations caused by applying force to the created propeller model were examined. In this study, CFRP (Carbon Fiber Reinforced Polymer) and PLA (Polylactide Acid) materials were preferred. The mechanical properties of materials are defined in the ANSYS program. As a result of the force applied to the propeller model, the amounts of deformation occurring in CFRP and PLA materials have been obtained. At the end of the study, the difference between the properties of the two materials was discussed.
- 30 June 2025
- Published by Selcuk University in International Journal of Aeronautics and Astronautics
- Vol. 6 (1) , 34-43
Open AccessAnalysis of a UAV propeller produced by various materials
Recently, Unmanned Aerial Vehicle (UAV) systems have started to attract great interest worldwide. With the orientation of the technology sector to this field, studies on UAV systems have gained momentum. Propellers, which are an important part of UAV systems, are of great importance to the propulsion system of the aircraft. Deformations that may occur, especially in propellers that are expected to have high strength, greatly affect flight safety. In this study, a two-bladed propeller model measuring 12 inches was created. The deformations caused by applying force to the created propeller model were examined. In this study, CFRP (Carbon Fiber Reinforced Polymer) and PLA (Polylactide Acid) materials were preferred. The mechanical properties of materials are defined in the ANSYS program. As a result of the force applied to the propeller model, the amounts of deformation occurring in CFRP and PLA materials have been obtained. At the end of the study, the difference between the properties of the two materials was discussed.
- Open Access
- 7 March 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (5) , 811-820
Manufacturing parameters’ effects on the flexural properties of 3D-printed PLA
In this study, the effects of infill ratio, layer thickness, nozzle temperature, and raster angle on the flexural strength of polylactic acid material were investigated through microstructural analysis. A total of 10 different sample groups were produced, changing the parameters of the filling ratio (20, 40, 60, 80 %), layer thickness (0.15, 0.20, 0.25, 0.30 mm), nozzle temperature (210, 220, 230 °C), and raster angle (±45°, 0/90°). Three-point bending tests were conducted using the Shimadzu bending machine, and the results were used to calculate maximum bending stress, modulus of elasticity, and strain values. The results showed that the values of maximum bending stress and modulus of elasticity vary significantly with changes in layer thickness, filling ratio, nozzle temperature, and raster angle. The Scanning Electron Microscopy (SEM) images were obtained from the longitudinal cross-section of the samples in the failure area. The obtained images were used to identify the gaps between beads, voids, porosity, filament rapture, pull-out breakage, elongation, and necking patterns on the samples. The variations in flexural properties were verified by using SEM micrographs in the failure area.
- 7 March 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (5) , 811-820
Open AccessManufacturing parameters’ effects on the flexural properties of 3D-printed PLA
In this study, the effects of infill ratio, layer thickness, nozzle temperature, and raster angle on the flexural strength of polylactic acid material were investigated through microstructural analysis. A total of 10 different sample groups were produced, changing the parameters of the filling ratio (20, 40, 60, 80 %), layer thickness (0.15, 0.20, 0.25, 0.30 mm), nozzle temperature (210, 220, 230 °C), and raster angle (±45°, 0/90°). Three-point bending tests were conducted using the Shimadzu bending machine, and the results were used to calculate maximum bending stress, modulus of elasticity, and strain values. The results showed that the values of maximum bending stress and modulus of elasticity vary significantly with changes in layer thickness, filling ratio, nozzle temperature, and raster angle. The Scanning Electron Microscopy (SEM) images were obtained from the longitudinal cross-section of the samples in the failure area. The obtained images were used to identify the gaps between beads, voids, porosity, filament rapture, pull-out breakage, elongation, and necking patterns on the samples. The variations in flexural properties were verified by using SEM micrographs in the failure area.
- 24 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (8) , 6983-6997
Gamma‐ray and neutron attenuation of carbon fiber/epoxy composites with carbon nanotubes and boron nitride nanoparticles for passive shielding applications in space
Composite materials have made far‐reaching changes in the space industry since they have been adopted into the structural and thermal control subsystems of space vehicles because of their several multi‐functions, including being lightweight as well as having advanced mechanical and thermal properties. The use of composites as space radiation shielding materials is also one of the most crucial applications because space radiation is a major impediment for current and future deep‐space missions. Investigation of carbon fiber composites with a diverse array of element and nanoparticle reinforcements has revealed their potential as an alternative to conventional radiation shielding materials in space. This study focused on the alleviation of gamma‐ray and neutron radiation by carbon fiber/epoxy composites incorporated with various weight ratios of carbon nanotube (CNT) and boron nitride (BN) nanoparticles. A narrow beam geometry setup was used for gamma radiation tests with a Cs‐137 gamma‐ray source, while neutron radiation experiments were conducted in a neutron howitzer with a 239Pu‐Be neutron source. Six groups of specimens, namely, pure carbon fiber/epoxy, 0.5 wt% CNT, 0.5 wt% BN, 0.5 wt% CNT + 0.5 wt% BN, 1 wt% CNT + 1 wt% BN, and 2 wt% BN, were examined against these two types of radiation. Results have indicated that the 2 wt% BN specimen showed the best attenuation properties against both gamma‐ray and neutron radiation among all tested specimens; furthermore, it was almost three times more effective against neutron radiation than against gamma‐ray radiation.Highlights: Varying weight ratios of CNT and BN nanoparticles used for radiation shielding. A Cs‐137 gamma‐ray source used in narrow beam geometry. Neutron radiation studies were conducted in a 239Pu‐Be neutron howitzer. The 2 wt% BN sample showed the best attenuation against gamma‐ray and neutron radiation. It resulted in an HVL of 6.86 cm for gamma‐ray radiation and 2.13 cm for neutron radiation.
- 24 December 2024
- Published by Wiley in Polymer Composites
- Vol. 46 (8) , 6983-6997
Gamma‐ray and neutron attenuation of carbon fiber/epoxy composites with carbon nanotubes and boron nitride nanoparticles for passive shielding applications in space
Composite materials have made far‐reaching changes in the space industry since they have been adopted into the structural and thermal control subsystems of space vehicles because of their several multi‐functions, including being lightweight as well as having advanced mechanical and thermal properties. The use of composites as space radiation shielding materials is also one of the most crucial applications because space radiation is a major impediment for current and future deep‐space missions. Investigation of carbon fiber composites with a diverse array of element and nanoparticle reinforcements has revealed their potential as an alternative to conventional radiation shielding materials in space. This study focused on the alleviation of gamma‐ray and neutron radiation by carbon fiber/epoxy composites incorporated with various weight ratios of carbon nanotube (CNT) and boron nitride (BN) nanoparticles. A narrow beam geometry setup was used for gamma radiation tests with a Cs‐137 gamma‐ray source, while neutron radiation experiments were conducted in a neutron howitzer with a 239Pu‐Be neutron source. Six groups of specimens, namely, pure carbon fiber/epoxy, 0.5 wt% CNT, 0.5 wt% BN, 0.5 wt% CNT + 0.5 wt% BN, 1 wt% CNT + 1 wt% BN, and 2 wt% BN, were examined against these two types of radiation. Results have indicated that the 2 wt% BN specimen showed the best attenuation properties against both gamma‐ray and neutron radiation among all tested specimens; furthermore, it was almost three times more effective against neutron radiation than against gamma‐ray radiation.Highlights: Varying weight ratios of CNT and BN nanoparticles used for radiation shielding. A Cs‐137 gamma‐ray source used in narrow beam geometry. Neutron radiation studies were conducted in a 239Pu‐Be neutron howitzer. The 2 wt% BN sample showed the best attenuation against gamma‐ray and neutron radiation. It resulted in an HVL of 6.86 cm for gamma‐ray radiation and 2.13 cm for neutron radiation.