Effect of Multiple Extrusion Cycles on Particle and Chemical Emissions and Mechanical and Thermal Properties of High-Density Polyethylene 3D Printing Filaments Made from Virgin and Post-Consumer Waste Plastics
Authors:
- Aleksandr B. StefaniakASAleksandr B. Stefaniak
- Lauren N. BowersLBLauren N. Bowers
- Callee M. WalshCWCallee M. Walsh
- Sonette Du PreezSPSonette Du Preez
- Elizabeth D. BrusakEBElizabeth D. Brusak
- Jason E. HamJHJason E. Ham
- Ryan F. LeBoufRLRyan F. LeBouf
- M. Abbas VirjiM. Abbas Virji
- Johan L. Du PlessisJPJohan L. Du Plessis
Open Access
Abstract
Distributed recycling of high-density polyethylene (HDPE) into filament for use in material extrusion 3D printing has been proposed as part of a circular economy. There is a gap in the understanding of the potential for HDPE to release contaminants that are potentially hazardous to human health during reuse. Herein, HDPE from post-consumer packaging waste was sorted into food and non-food (NF) streams and virgin HDPE was taken as a benchmark material. All materials were extruded into filaments and recycled multiple times while monitoring emissions. In general, particle and organic chemical emissions decreased by 93 to 99% and 73 to 99%, respectively, with increased reprocessing cycle without appreciable decline in mechanical (Young’s modulus decreased by 5 to 16%), processability (melt flow index stable from 0.2 to 0.7 g/10 min for waste plastics), and thermal properties (crystallinity ranged from a 6% decrease to a 9% increase) of plastics. An exception was a sub-stream of NF plastic that had increased particle emissions (up to 3100%) with reprocessing cycle. Reductions in emissions during filament extrusion appeared to be more influenced by reprocessing cycle than by any specific process step (grinding, etc.). The progressive decline in emissions without appreciable loss of polymer integrity could be exploited to pre-condition HDPE to reduce potential hazardous emissions prior to extruding into filament. This work helps fill the knowledge gap on approaches to recycling plastics in distributed settings such as home-based businesses, which is critical for developing effective recommendations for controls to enable safe work practices such as the use of ventilation to minimize exposures.Keywords
This publication has 52 references indexed in Scilit:
- FDM-based additive manufacturing of recycled thermoplastics and associated compositesJournal of Material Cycles and Waste Management, 2023
- The impact of thermal reprocessing of 3D printable polymers on their mechanical performance and airborne pollutant profilesJournal of Polymer Research, 2021
- Optimized workflow for unknown screening using gas chromatography high‐resolution mass spectrometry expands identification of contaminants in silicone personal passive samplersRapid Communications in Mass Spectrometry, 2021
- The impact of impurities on the mechanical properties of recycled polyethylenePackaging Technology and Science, 2020
- Perspectives on additives for polymers. Part 2. Aspects of photostabilization and role of fillers and pigmentsJournal of Vinyl and Additive Technology, 2020
- Perspectives on additives for polymers. 1. Aspects of stabilizationJournal of Vinyl and Additive Technology, 2020
- Mechanical Recycling of Packaging Plastics: A ReviewMacromolecular Rapid Communications, 2020
- Physical Characterization and Pre-assessment of Recycled High-Density Polyethylene as 3D Printing MaterialJournal of Polymers and the Environment, 2016
- Detergent impurity effect on recycled HDPE: Properties after repetitive processingJournal of Applied Polymer Science, 2016
- Degradation of polyethylene during extrusion. II. Degradation of low‐density polyethylene, linear low‐density polyethylene, and high‐density polyethylene in film extrusionJournal of Applied Polymer Science, 2003