Comparative Analysis of the Mechanical and Biofilm Surface Formation of 3D Printed Resins and Milled PMMA Blocks With and Without Inorganic Fillers
Open Access
- 13 August 2026
- journal article
- research article
- Published by Wiley in Clinical and Experimental Dental Research
- Vol. 12 (4) , e70433
Abstract
Objectives: Despite the growing number of studies assessing the performance of temporary restorative materials fabricated through CAD/CAM technologies, comparative analyses among 3D printed resins and milled PMMA blocks with differing compositions remain limited. This study compared mechanical and biofilm surface formation of 3D printed resins PMMA blocks with different compositions, using composite resin as control. Material and Methods: Bar‑shaped (25 × 2 × 2 mm) and disc‑shaped (6 × 2 mm) specimens were fabricated. Flexural strength was evaluated by three‑point bending (ISO 4049), and Vickers microhardness was recorded. Multispecies biofilm formation was quantified using CFU/mL and examined morphologically via SEM. Statistical significance was set at α = 0.05. Results: The 3D printed resins and milled hybrid PMMA showed the lowest flexural strength, with no significant differences between them, while the composite resin achieved the highest and statistically superior values ( p < 0.001). 3D printed resin without inorganic fillers showed the lowest Vickers microhardness values (12.66 ± 0.83 HK) while 3D printed resin with inorganic fillers (15.20 ± 1.94 HK) and milled conventional PMMA (16.03 ± 1.35 HK) exhibited higher values. However, none of them differed statistically from the 3D printed resin without inorganic fillers ( p = 0.064). Conversely, milled hybrid PMMA (16.67 ± 2.10 HK) demonstrated significantly higher Vickers microhardness than 3 d printed resin with inorganic fillers ( p < 0.001). Biofilm formation ranged from 2.26 × 10 7 to 2.82 × 10 7 CFU/mL, with no significant differences among materials ( p > 0.05). Conclusions: Milled and 3D printed materials demonstrated comparable mechanical behavior while composite resin remained the performance benchmark. Material selection for provisional restorations should account for mechanical behavior and biological interactions, as surface treatment and clinical conditions may influence microbial colonization.Keywords
This publication has 23 references indexed in Scilit:
- 3D‐printed denture base resins: Glazing as an alternative to improve surface, mechanical, and microbiological propertiesJournal of Prosthodontics, 2024
- Evaluating mechanical and surface properties of zirconia-containing composites: 3D printing, subtractive, and layering techniquesJournal of the Mechanical Behavior of Biomedical Materials, 2024
- 3D-printed and conventional provisional single crown fabrication on anterior implants: A randomized clinical trialDental Materials, 2023
- In Vitro Dental Plaque Culture Model for Biofilm Structural AnalysesCurrent Protocols, 2023
- Micromechanical interlocking structure at the filler/resin interface for dental composites: a reviewInternational Journal of Oral Science, 2023
- Effect of APTES- or MPTS-Conditioned Nanozirconia Fillers on Mechanical Properties of Bis-GMA-Based Resin CompositesACS Omega, 2020
- Biofilms: an emergent form of bacterial lifeNature Reviews Microbiology, 2016
- Poly(methyl-methacrylate) nanocomposites with low silica additionThe Journal of Prosthetic Dentistry, 2014
- Interface effects on mechanical properties of particle-reinforced compositesDental Materials, 2004
- Comparison of surface roughness of oral hard materials to the threshold surface roughness for bacterial plaque retention: A review of the literatureDental Materials, 1997