Effect of Nail Size, Insertion, and Δ Canal-Nail on the Development of a Nonunion After Intramedullary Nailing of Femoral Shaft Fractures
- 1 November 2019
- journal article
- research article
- Published by Wolters Kluwer Health in Journal of Orthopaedic Trauma
- Vol. 33 (11) , 559-563
Abstract
Objective: To determine whether intramedullary nail (IMN) diameter, antegrade versus retrograde insertion, or the difference between the canal and IMN diameter affect femoral shaft fracture healing. Design: Retrospective analysis of a prospective database. Setting: Level One Regional Trauma Center. Patients/Participants: Seven hundred thirty-three femoral shaft fractures (OTA/AO 32) treated with an IMN between 1999 and 2017. After exclusion criteria, 484 fractures remained in the final analysis. Intervention: Closed section, cannulated, interlocked, titanium alloy IMN using a reamed insertion technique. Main Outcome Measurements: Nonunion, IMN size (10, 11.5, and 13 mm), antegrade versus retrograde insertion, Δ canal-nail diameter (ΔD) after reaming (2 mm). Results: IMN diameters used were as follows: 314/10 mm (64%), 137/11.5 mm (28%), and 33/13 mm (8%). Forty-five percent were placed in antegrade versus 55% retrograde. Four hundred fifty-six fractures (94.2%) healed uneventfully. There were no IMN failures. 10/484 IMNs (2%) had broken interlocking screws; only 4 were associated with a NU. Average time to union was 23 weeks (12–119). Twenty-eight (5.8%) developed NU. There was no statistical correlation between (1) the NU rate and IMN diameter: 10 mm, 6.3%; 11.5 mm, 5.1%; 13 mm, 3% (P = 0.8, power = 0.85), (2) the NU rate and ΔD: 7.1% 2 mm (P = 0.36), (3) the NU rate and fracture location: Prox = 11%, Mid = 5%, Dist = 3% (P = 0.13), or (4) the NU rate and antegrade (7.2%) versus retrograde (4.2%) insertion (P = 0.24). Conclusion: Similar healing rates occurred regardless of IMN diameter, Δ canal-nail diameter after reaming, or insertion site. This indicates that a closed section, cannulated, interlocked, titanium alloy IMN with a diameter of 10 mm can be considered the standard diameter for the treatment of acute femoral shaft fractures, regardless of entry point. This should be associated with less reaming and therefore shorter operative times, and possibly less hospital implant inventories as well. Larger diameter IMN should be reserved for revision surgery. Level of Evidence: Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.Keywords
This publication has 27 references indexed in Scilit:
- A Prospective Functional Outcome and Motion Analysis Evaluation of the Hip Abductors After Femur Fracture and Antegrade NailingJournal of Orthopaedic Trauma, 2008
- Reamed Versus Unreamed Intramedullary Nailing of the Femur: Comparison of the Rate of ARDS in Multiple Injured PatientsJournal of Orthopaedic Trauma, 2006
- The Classic: Early versus Delayed Stabilization of Femoral FracturesClinical Orthopaedics and Related Research, 2004
- Orthopaedic Trauma Association Edwin G. Bovill, Jr., M.D. AwardJournal of Orthopaedic Trauma, 2000
- The Treatment of Femoral Shaft Fractures Using Intramedullary Interlocked Nails with and without Intramedullary Reaming: A Preliminary ReportJournal of Orthopaedic Trauma, 1997
- Small Versus Large Diameter Closed-Section Femoral Nails for the Treatment of Femoral Shaft FracturesThe Journal of Trauma: Injury, Infection, and Critical Care, 1996
- Does the Reamer Type Influence the Degree of Lung Dysfunction After Femoral Nailing Following Severe Trauma? An Animal StudyJournal of Orthopaedic Trauma, 1994
- Initial Experience with the Treatment of Supracondylar Femoral Fractures Using the Supracondylar Intramedullary Nail: A Preliminary ReportJournal of Orthopaedic Trauma, 1994
- PRIMARY INTRAMEDULLARY FEMUR FIXATION IN MULTIPLE TRAUMA PATIENTS WITH ASSOCIATED LUNG CONTUSION—A CAUSE OF POSTTRAUMATIC ARDS?1993
- Mechanical Characterization of Femoral Interlocking Intramedullary Nailing SystemsJournal of Orthopaedic Trauma, 1991