Influence of Microstructure on the Mechanical Properties of Low Carbon UNS S41003 Stainless Steel
Open Access
- 1 January 2025
- journal article
- research article
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250216
Abstract
UNS S41003 stainless steel is a lean stainless steel with 10.5-11% Cr, low carbon (<0.03%C), and small Ni addition. The composition is such that, depending on the processing route, the microstructure can be ferritic, martensitic, or ferritic-martensitic. Specimens acquired from the steelmaker were produced by hot rolling, with and without batch annealing. Two other sets of specimens were created by heat treating at 1000°C followed by water quenching. The microstructures of the four groups of specimens were characterized by scanning electron microscopy (SEM) with electron backscattered scanning diffraction (EBSD). The mechanical properties were measured by tensile tests, hardness, and impact toughness. This study demonstrates the optimal combination of mechanical resistance and toughness in hot rolling samples, which presented a fine grain size of martensite with fine carbides and 23.3% of elongated δ-ferrite. The hot rolled samples show a yield strength 6.2% higher than the quenched samples, and 152.1% higher than the annealed ones. The hot rolled steel presents a higher impact toughness, 31.7 J, 16.1% superior to the annealed material. The quenching heat treatments decreased the %δ ferrite and increased the grain size. The material annealed has a microstructure of equiaxial α-ferrite grains and intergranular chromium carbides.Keywords
Funding Information
- CNPq (308244/2022-2)
- CNPq (E-26/211.412/2021)
- CNPq (E-26/200.525/2025)
- CNPq (E-26/200.423/2023)
- FAPERJ (308244/2022-2)
- FAPERJ (E-26/211.412/2021)
- FAPERJ (E-26/200.525/2025)
- FAPERJ (E-26/200.423/2023)
This publication has 30 references indexed in Scilit:
- In situ evaluation of sensitization in the heat affected zone of supermartensitic stainless steel welded with superduplex filler metalEngineering Failure Analysis, 2024
- Microstructural Characterization of Dual-Phase Low-Carbon Steel as Function of Inter-critical AnnealingMetallography, Microstructure, and Analysis, 2024
- Microstructural Characterization of Low Carbon UNS S41003 Stainless Steel with Different Processing Routes (Hot Rolling and Annealing)Metallography, Microstructure, and Analysis, 2024
- Quantification of grain boundary effects on the geometrically necessary dislocation density evolution and strain hardening of polycrystalline Mg 4Al using in situ tensile testing in scanning electron microscope and HR-EBSDJournal of Magnesium and Alloys, 2024
- Effects of post-weld heat treatments in microstructure, mechanical properties, and corrosion resistance of simulated heat-affected zone of supermartensitic steel UNS S41426The International Journal of Advanced Manufacturing Technology, 2024
- Microstructure, mechanical properties, and corrosion resistance of supermartensitic steel UNS S41426: comparison between forged and hot-rolled seamless pipeThe International Journal of Advanced Manufacturing Technology, 2022
- Microstructure and Corrosion Properties of S400E Sorbite Stainless SteelMetallography, Microstructure, and Analysis, 2022
- Effect of Aging on Transformation Behavior of Reverted Austenite and Toughness in Co-Free Maraging Stainless SteelJournal of Materials Engineering and Performance, 2022
- Mechanical performance of welds using ASTM A709 grade 50CR steel as base metalJournal of Constructional Steel Research, 2020
- The role of microstructure and grain orientations on intergranular cracking susceptibility of UNS 17400 martensitic stainless steelEngineering Failure Analysis, 2017