Rodrigo de Carvalho Paes Loureiro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rodrigo de Carvalho Paes Loureiro has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Hamilton Ferreira Gomes de Abreu
6 shared publications- Mohammad Masoumi
Centro de Engenharia, Modelagem e Ciências Sociais Aplicadas, Universidade Federal do ABC, Santo André, Brazil
5 shared publications - Hamilton Ferreira Gomes de Abreu
Universidade Federal do Ceará, Brasil
4 shared publications Miloslav Béreš
4 shared publications- Samuel Filgueiras Rodrigues
Mechanical and Thermomechanical Testing Laboratory (LabEnsaios) Graduate Program in Materials Science and Technology (PPGCTM) Federal Institute of Education, Science and Technology of Maranhão, Campus Monte Castelo São Luís Maranhão Brazil
4 shared publications - Marcos Natan da Silva Lima
Mechanical and Thermomechanical Testing Laboratory (LabEnsaios) Graduate Program in Materials Science and Technology (PPGCTM) Federal Institute of Education, Science and Technology of Maranhão, Campus Monte Castelo São Luís Maranhão Brazil
3 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250216
Influence of Microstructure on the Mechanical Properties of Low Carbon UNS S41003 Stainless Steel
UNS S41003 stainless steel is a lean stainless steel with 10.5-11% Cr, low carbon (<0.03%C), and small Ni addition. The composition is such that, depending on the processing route, the microstructure can be ferritic, martensitic, or ferritic-martensitic. Specimens acquired from the steelmaker were produced by hot rolling, with and without batch annealing. Two other sets of specimens were created by heat treating at 1000°C followed by water quenching. The microstructures of the four groups of specimens were characterized by scanning electron microscopy (SEM) with electron backscattered scanning diffraction (EBSD). The mechanical properties were measured by tensile tests, hardness, and impact toughness. This study demonstrates the optimal combination of mechanical resistance and toughness in hot rolling samples, which presented a fine grain size of martensite with fine carbides and 23.3% of elongated δ-ferrite. The hot rolled samples show a yield strength 6.2% higher than the quenched samples, and 152.1% higher than the annealed ones. The hot rolled steel presents a higher impact toughness, 31.7 J, 16.1% superior to the annealed material. The quenching heat treatments decreased the %δ ferrite and increased the grain size. The material annealed has a microstructure of equiaxial α-ferrite grains and intergranular chromium carbides.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20250216
Open AccessInfluence of Microstructure on the Mechanical Properties of Low Carbon UNS S41003 Stainless Steel
UNS S41003 stainless steel is a lean stainless steel with 10.5-11% Cr, low carbon (<0.03%C), and small Ni addition. The composition is such that, depending on the processing route, the microstructure can be ferritic, martensitic, or ferritic-martensitic. Specimens acquired from the steelmaker were produced by hot rolling, with and without batch annealing. Two other sets of specimens were created by heat treating at 1000°C followed by water quenching. The microstructures of the four groups of specimens were characterized by scanning electron microscopy (SEM) with electron backscattered scanning diffraction (EBSD). The mechanical properties were measured by tensile tests, hardness, and impact toughness. This study demonstrates the optimal combination of mechanical resistance and toughness in hot rolling samples, which presented a fine grain size of martensite with fine carbides and 23.3% of elongated δ-ferrite. The hot rolled samples show a yield strength 6.2% higher than the quenched samples, and 152.1% higher than the annealed ones. The hot rolled steel presents a higher impact toughness, 31.7 J, 16.1% superior to the annealed material. The quenching heat treatments decreased the %δ ferrite and increased the grain size. The material annealed has a microstructure of equiaxial α-ferrite grains and intergranular chromium carbides.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20240586
Non-Destructive Investigation of Microstructural Transformations and Mechanical Hardening by Electromagnetic Techniques in Cold-Rolled Ferritic-Pearlitic Steel Wire of Flexible Pipelines
Offshore oil and gas exploration in deep areas raises the need to develop equipment monitoring techniques to detect possible defects and prevent catastrophic failures. This work sought to analyze the feasibility of using non-destructive electromagnetic techniques - Magnetic Barkhausen Noise (MBN), Magnetic Hysteresis and Electrical Resistivity - in the identification of predominant stresses, microstructural transformations and mechanical behavior of a steel used in the manufacture of flexible Risers. The material was analyzed as received and cold rolled with 5, 10, 20, and 35% reduction rates. The signals were related to data obtained by Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD) and hardness tests. The results show that with increasing strain, the MBN peak amplitude decreases (95.0%), the energy required to reach magnetic saturation increases (23.2%), and the electrical resistivity increases (41.6%). The variation of these signs indicates an increase in structural heterogeneities, such as elongation of cementite lamellae, increase in dislocation density, and non-homogeneous stress field distribution, which increase the area of sites fixation of magnetic domains and decrease the flow of free electrons. The sensitivity in detecting changes of the techniques in question demonstrates their efficiency in inspecting flexible ducts installed in areas of difficult access.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 28 (suppl 1) , e20240586
Open AccessNon-Destructive Investigation of Microstructural Transformations and Mechanical Hardening by Electromagnetic Techniques in Cold-Rolled Ferritic-Pearlitic Steel Wire of Flexible Pipelines
Offshore oil and gas exploration in deep areas raises the need to develop equipment monitoring techniques to detect possible defects and prevent catastrophic failures. This work sought to analyze the feasibility of using non-destructive electromagnetic techniques - Magnetic Barkhausen Noise (MBN), Magnetic Hysteresis and Electrical Resistivity - in the identification of predominant stresses, microstructural transformations and mechanical behavior of a steel used in the manufacture of flexible Risers. The material was analyzed as received and cold rolled with 5, 10, 20, and 35% reduction rates. The signals were related to data obtained by Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD) and hardness tests. The results show that with increasing strain, the MBN peak amplitude decreases (95.0%), the energy required to reach magnetic saturation increases (23.2%), and the electrical resistivity increases (41.6%). The variation of these signs indicates an increase in structural heterogeneities, such as elongation of cementite lamellae, increase in dislocation density, and non-homogeneous stress field distribution, which increase the area of sites fixation of magnetic domains and decrease the flow of free electrons. The sensitivity in detecting changes of the techniques in question demonstrates their efficiency in inspecting flexible ducts installed in areas of difficult access.
- Open Access
- 16 April 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 3675-3689
Evidence of dynamic ferrite transformation during thermomechanical simulation of an X70 microalloyed steel above Ae3 temperature
- 16 April 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 3675-3689
Open AccessEvidence of dynamic ferrite transformation during thermomechanical simulation of an X70 microalloyed steel above Ae3 temperature
- Open Access
- 1 January 2024
- Published by Even3
- Vol. 1, 1
A INFLUÊNCIA DO TRATAMENTO ISOTÉRMICO NA MICROESTRUTURA DE UM AÇO AISI 1070.
Neste estudo, foi investigado os produtos de transformação em aço AISI 1070, juntamente com o processo de decomposição isotérmica da austenita em duas fases distintas. Esses tipos de aços desempenham um papel fundamental como armaduras de tração em diversas aplicações, incluindo as indústrias de petróleo e gás. Um dilatômetro de deformação dilatométrica em um simulador termomecânico para realizar um resfriamento rápido da temperatura de austenitização de 850 °C para temperaturas isotérmicas de 360 °C. Durante esse processo, registramos a cinética de transformação e elaboramos um diagrama de transformação isotérmica, que foi validado por meio de observações de mudanças microestruturais. Os resultados revelaram que a microestrutura inicial, composta por ferrita proeutetóide e perlita, evoluiu para uma combinação de martensita, bainita e austenita retida. Além disso, a análise EBSD destacou as diferenças de deformação entre as diversas microestruturas presentes durante o tratamento térmico, sugerindo a presença de maior energia e densidade de discordâncias na martensita.
- 1 January 2024
- Published by Even3
- Vol. 1, 1
Open AccessA INFLUÊNCIA DO TRATAMENTO ISOTÉRMICO NA MICROESTRUTURA DE UM AÇO AISI 1070.
Neste estudo, foi investigado os produtos de transformação em aço AISI 1070, juntamente com o processo de decomposição isotérmica da austenita em duas fases distintas. Esses tipos de aços desempenham um papel fundamental como armaduras de tração em diversas aplicações, incluindo as indústrias de petróleo e gás. Um dilatômetro de deformação dilatométrica em um simulador termomecânico para realizar um resfriamento rápido da temperatura de austenitização de 850 °C para temperaturas isotérmicas de 360 °C. Durante esse processo, registramos a cinética de transformação e elaboramos um diagrama de transformação isotérmica, que foi validado por meio de observações de mudanças microestruturais. Os resultados revelaram que a microestrutura inicial, composta por ferrita proeutetóide e perlita, evoluiu para uma combinação de martensita, bainita e austenita retida. Além disso, a análise EBSD destacou as diferenças de deformação entre as diversas microestruturas presentes durante o tratamento térmico, sugerindo a presença de maior energia e densidade de discordâncias na martensita.
- Open Access
- 22 September 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 9406-9418
Effect of combined cold deformation and subsequent heat treatment on the microstructure, texture, mechanical properties and cementite spheroidization in AISI 1070 steel
- 22 September 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 26, 9406-9418
Open AccessEffect of combined cold deformation and subsequent heat treatment on the microstructure, texture, mechanical properties and cementite spheroidization in AISI 1070 steel
- Open Access
- 14 January 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 845-858
Improvement of tensile properties by controlling the microstructure and crystallographic data in commercial pearlitic carbon-silicon steel via quenching and partitioning (Q&P) process
- 14 January 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 845-858
Open AccessImprovement of tensile properties by controlling the microstructure and crystallographic data in commercial pearlitic carbon-silicon steel via quenching and partitioning (Q&P) process
- Open Access
Optimization of Thermomechanical Processing under Double-Pass Hot Compression Tests of a High Nb and N-Bearing Austenitic Stainless-Steel Biomaterial Using Artificial Neural Networks
Physical simulation is a useful tool for examining the events that occur during the multiple stages of thermomechanical processing, since it requires no industrial equipment. Instead, it involves hot deformation testing in the laboratory, similar to industrial-scale processes, such as controlled hot rolling and forging, but under different conditions of friction and heat transfer. Our purpose in this work was to develop an artificial neural network (ANN) to optimize the thermomechanical behavior of stainless-steel biomaterial in a double-pass hot compression test, adapted to the Arrhenius–Avrami constitutive model. The method consists of calculating the static softening fraction (Xs) and mean recrystallized grain size (ds), implementing an ANN based on data obtained from hot compression tests, using a vacuum chamber in a DIL 805A/D quenching dilatometer at temperatures of 1000, 1050, 1100 and 1200 °C, in passes (ε1 = ε2) of 0.15 and 0.30, a strain rate of 1.0 s−1 and time between passes (tp) of 1, 10, 100, 400, 800 and 1000 s. The constitutive analysis and the experimental and ANN-simulated results were in good agreement, indicating that ASTM F-1586 austenitic stainless steel used as a biomaterial undergoes up to Xs = 40% of softening due solely to static recovery (SRV) in less than 1.0 s interval between passes (tp), followed by metadynamic recrystallization (MDRX) at strains greater than 0.30. At T > 1050 °C, the behavior of the softening curves Xs vs. tp showed the formation of plateaus for long times between passes (tp), delaying the softening kinetics and modifying the profile of the curves produced by the moderate stacking fault energy, γsfe = 69 mJ/m2 and the strain-induced interaction between recrystallization and precipitation (Z-phase). Thus, the use of this ANN allows one to optimize the ideal thermomechanical parameters for distribution and refinement of grains with better mechanical properties.
Open AccessOptimization of Thermomechanical Processing under Double-Pass Hot Compression Tests of a High Nb and N-Bearing Austenitic Stainless-Steel Biomaterial Using Artificial Neural Networks
Physical simulation is a useful tool for examining the events that occur during the multiple stages of thermomechanical processing, since it requires no industrial equipment. Instead, it involves hot deformation testing in the laboratory, similar to industrial-scale processes, such as controlled hot rolling and forging, but under different conditions of friction and heat transfer. Our purpose in this work was to develop an artificial neural network (ANN) to optimize the thermomechanical behavior of stainless-steel biomaterial in a double-pass hot compression test, adapted to the Arrhenius–Avrami constitutive model. The method consists of calculating the static softening fraction (Xs) and mean recrystallized grain size (ds), implementing an ANN based on data obtained from hot compression tests, using a vacuum chamber in a DIL 805A/D quenching dilatometer at temperatures of 1000, 1050, 1100 and 1200 °C, in passes (ε1 = ε2) of 0.15 and 0.30, a strain rate of 1.0 s−1 and time between passes (tp) of 1, 10, 100, 400, 800 and 1000 s. The constitutive analysis and the experimental and ANN-simulated results were in good agreement, indicating that ASTM F-1586 austenitic stainless steel used as a biomaterial undergoes up to Xs = 40% of softening due solely to static recovery (SRV) in less than 1.0 s interval between passes (tp), followed by metadynamic recrystallization (MDRX) at strains greater than 0.30. At T > 1050 °C, the behavior of the softening curves Xs vs. tp showed the formation of plateaus for long times between passes (tp), delaying the softening kinetics and modifying the profile of the curves produced by the moderate stacking fault energy, γsfe = 69 mJ/m2 and the strain-induced interaction between recrystallization and precipitation (Z-phase). Thus, the use of this ANN allows one to optimize the ideal thermomechanical parameters for distribution and refinement of grains with better mechanical properties.
- Open Access
Dynamic Ferrite Formation and Evolution above the Ae3 Temperature during Plate Rolling Simulation of an API X80 Steel
Thermo-mechanically controlled rolling is a technique used to produce steel strips and plates. One of the steels widely used in the production of heavy plates for application in oil and gas pipelines is API X80. The hot rolling process of this family of steels consists of applying deformation passes at high temperatures, mainly above Ae3, inside the austenite phase field. It has been shown that during deformation, the phenomenon of dynamic transformation (DT) of austenite into ferrite leads to lower hot deformation resistance within the stable austenite region. In this investigation, hot torsion simulations of an industrial rolling process under continuous cooling conditions were used to monitor the formation of ferrite by DT. Stress–strain flow curves and equivalent mean flow stresses followed by sample characterization via optical and electron microscopy showed the inevitable formation of ferrite above the Ae3. The employed 10-pass deformation schedule was divided into 5 roughing and 5 finishing passes, thereby promoting an increased volume fraction of ferrite and decreased critical strain for the onset of DT and dynamic recrystallization (DRX). A microstructural analysis confirmed the formation of ferrite from the first roughing strain until the last finishing pass. The volume fraction of DT ferrite increased due to strain accumulation, an increased number of deformation passes and as the temperature approached the Ae3, leading to a characteristic torsion texture at the end of the simulation.
Open AccessDynamic Ferrite Formation and Evolution above the Ae3 Temperature during Plate Rolling Simulation of an API X80 Steel
Thermo-mechanically controlled rolling is a technique used to produce steel strips and plates. One of the steels widely used in the production of heavy plates for application in oil and gas pipelines is API X80. The hot rolling process of this family of steels consists of applying deformation passes at high temperatures, mainly above Ae3, inside the austenite phase field. It has been shown that during deformation, the phenomenon of dynamic transformation (DT) of austenite into ferrite leads to lower hot deformation resistance within the stable austenite region. In this investigation, hot torsion simulations of an industrial rolling process under continuous cooling conditions were used to monitor the formation of ferrite by DT. Stress–strain flow curves and equivalent mean flow stresses followed by sample characterization via optical and electron microscopy showed the inevitable formation of ferrite above the Ae3. The employed 10-pass deformation schedule was divided into 5 roughing and 5 finishing passes, thereby promoting an increased volume fraction of ferrite and decreased critical strain for the onset of DT and dynamic recrystallization (DRX). A microstructural analysis confirmed the formation of ferrite from the first roughing strain until the last finishing pass. The volume fraction of DT ferrite increased due to strain accumulation, an increased number of deformation passes and as the temperature approached the Ae3, leading to a characteristic torsion texture at the end of the simulation.
- Open Access
- 11 May 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 19, 7-19
Influence of cold deformation on microstructure, crystallographic orientation and tensile properties of an experimental austenitic Fe–26Mn-0.4C steel
- 11 May 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 19, 7-19
Open AccessInfluence of cold deformation on microstructure, crystallographic orientation and tensile properties of an experimental austenitic Fe–26Mn-0.4C steel
- 27 January 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (6) , 4642-4654
Effect of Pre-strain on Microstructure, Texture, and Strengthening of Fully Pearlitic Steel
- 27 January 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (6) , 4642-4654
Effect of Pre-strain on Microstructure, Texture, and Strengthening of Fully Pearlitic Steel