Micro‐Raman analysis and finite‐element modeling of 3 C‐SiC microstructures
Authors:
- N. PilusoNPN. Piluso
- R. AnzaloneRAR. Anzalone
- M. CamardaMCM. Camarda
- A. SeverinoASA. Severino
- A. La MagnaAMA. La Magna
- G. D'ARrigoGDG. D'ARrigo
- F. La ViaF. La Via
- 1 September 2012
- journal article
- research article
- Published by Wiley in Journal of Raman Spectroscopy
- Vol. 44 (2) , 299-306
Abstract
Micro‐ and nano‐electromechanical systems (MEMS and NEMS) fabricated in 3 C‐SiC are receiving particular attention thanks to the material physical properties: its wide band gap (2.3 eV), its ability to operate at high temperatures, its mechanical strength and its inertness to the exposure in corrosive environments. However, high residual stress (which is normally generated during the hetero‐epitaxial growth process) makes the use of 3 C‐SiC in Si‐based MEMS fabrication techniques very limited leading to a failure of micro‐machined/sensor structures.In this paper, micro‐Raman characterizations and finite‐element modeling (FEM) of microstructures realized on poly and single‐crystal (100) 3 C‐SiC/Si films are performed. Transverse optical (TO) Raman mode analysis reveals the stress relaxation on the free standing structure (796.5 cm−1) respect to the stressed unreleased region (795.7 cm−1). Also, microstructures as cantilever, bridge and planar rotating probe show an intense stress field located around the undercut region. Here, the TO Raman mode undergoes an intense shift, up to 2 cm−1, ascribed to the modification of the Raman stress tensor. Indeed, the generalized axial regime, described by diagonal components of the Raman stress tensor, cannot be applied in this region. Raman maps analysis and FEM simulations show the ‘activation’ of the shear stress, i.e. non‐diagonal components of the stress tensor. The stress‐Raman modes shift correlation, in the case of fully non‐diagonal stress tensors, has been investigated. The aim of future works will be to minimize the stress field generation and the defects density within the epitaxial layer. Copyright © 2012 John Wiley & Sons, Ltd.Keywords
This publication has 30 references indexed in Scilit:
- Strain Field Analysis of 3C-SiC Free-Standing Microstructures by Micro-Raman and Theoretical ModellingMaterials Science Forum, 2012
- Wafer Cut Effect on Hetero-Epitaxial 3C-SiC Film for MEMS ApplicationElectrochemical and Solid-State Letters, 2012
- Complete Determination of the Local Stress Field in Epitaxial Thin Films Using Single MicrostructureMaterials Science Forum, 2011
- Raman Stress Characterization of Hetero-Epitaxial 3C-SiC Free Standing StructuresMaterials Science Forum, 2011
- Defect Influence on Heteroepitaxial 3C-SiC Young’s ModulusElectrochemical and Solid-State Letters, 2011
- Residual Stress Measurement and Simulation of 3C-SiC Single and Poly Crystal CantileversMaterials Science Forum, 2010
- Development of a high-growth rate 3C-SiC on Si CVD processMRS Proceedings, 2006
- Determination of the elastic modulus of thin film materials using self-deformed micromachined cantileversJournal of Micromechanics and Microengineering, 1999
- Resonance Raman scattering in Si at elevated temperaturesPhysical Review B, 1984
- Pressure dependence of the optical phonons and transverse effective charge in-SiCPhysical Review B, 1982