N. Piluso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
N. Piluso has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Francesco La Via
CNR-IMM
3 shared publications A. Severino
2 shared publications- Massimo Camarda
STLab srl, Via Anapo 53, 95126 Catania, Italy
2 shared publications A. Auditore
ST-Microelectronics, 95121 Catania, Italy
1 shared publicationA. La Magna
1 shared publication- Antonino La Magna
Istituto per la Microelettronica e Microsistemi, National Research Council of Italy, 95121 Catania, Italy
1 shared publication
Latest Publications
- 1 September 2012
- Published by Wiley in Journal of Raman Spectroscopy
- Vol. 44 (2) , 299-306
Micro‐Raman analysis and finite‐element modeling of 3 C‐SiC microstructures
Micro‐ and nano‐electromechanical systems (MEMS and NEMS) fabricated in 3 C‐SiC are receiving particular attention thanks to the material physical properties: its wide band gap (2.3 eV), its ability to operate at high temperatures, its mechanical strength and its inertness to the exposure in corrosive environments. However, high residual stress (which is normally generated during the hetero‐epitaxial growth process) makes the use of 3 C‐SiC in Si‐based MEMS fabrication techniques very limited leading to a failure of micro‐machined/sensor structures.In this paper, micro‐Raman characterizations and finite‐element modeling (FEM) of microstructures realized on poly and single‐crystal (100) 3 C‐SiC/Si films are performed. Transverse optical (TO) Raman mode analysis reveals the stress relaxation on the free standing structure (796.5 cm−1) respect to the stressed unreleased region (795.7 cm−1). Also, microstructures as cantilever, bridge and planar rotating probe show an intense stress field located around the undercut region. Here, the TO Raman mode undergoes an intense shift, up to 2 cm−1, ascribed to the modification of the Raman stress tensor. Indeed, the generalized axial regime, described by diagonal components of the Raman stress tensor, cannot be applied in this region. Raman maps analysis and FEM simulations show the ‘activation’ of the shear stress, i.e. non‐diagonal components of the stress tensor. The stress‐Raman modes shift correlation, in the case of fully non‐diagonal stress tensors, has been investigated. The aim of future works will be to minimize the stress field generation and the defects density within the epitaxial layer. Copyright © 2012 John Wiley & Sons, Ltd.
- 1 September 2012
- Published by Wiley in Journal of Raman Spectroscopy
- Vol. 44 (2) , 299-306
Micro‐Raman analysis and finite‐element modeling of 3 C‐SiC microstructures
Micro‐ and nano‐electromechanical systems (MEMS and NEMS) fabricated in 3 C‐SiC are receiving particular attention thanks to the material physical properties: its wide band gap (2.3 eV), its ability to operate at high temperatures, its mechanical strength and its inertness to the exposure in corrosive environments. However, high residual stress (which is normally generated during the hetero‐epitaxial growth process) makes the use of 3 C‐SiC in Si‐based MEMS fabrication techniques very limited leading to a failure of micro‐machined/sensor structures.In this paper, micro‐Raman characterizations and finite‐element modeling (FEM) of microstructures realized on poly and single‐crystal (100) 3 C‐SiC/Si films are performed. Transverse optical (TO) Raman mode analysis reveals the stress relaxation on the free standing structure (796.5 cm−1) respect to the stressed unreleased region (795.7 cm−1). Also, microstructures as cantilever, bridge and planar rotating probe show an intense stress field located around the undercut region. Here, the TO Raman mode undergoes an intense shift, up to 2 cm−1, ascribed to the modification of the Raman stress tensor. Indeed, the generalized axial regime, described by diagonal components of the Raman stress tensor, cannot be applied in this region. Raman maps analysis and FEM simulations show the ‘activation’ of the shear stress, i.e. non‐diagonal components of the stress tensor. The stress‐Raman modes shift correlation, in the case of fully non‐diagonal stress tensors, has been investigated. The aim of future works will be to minimize the stress field generation and the defects density within the epitaxial layer. Copyright © 2012 John Wiley & Sons, Ltd.
- 1 March 2012
- Published by Elsevier in Physica E: Low-dimensional Systems and Nanostructures
- Vol. 44 (6) , 1005-1008
Morphology and distribution of carbon nanostructures in a deposit produced by arc discharge in liquid nitrogen
- 1 March 2012
- Published by Elsevier in Physica E: Low-dimensional Systems and Nanostructures
- Vol. 44 (6) , 1005-1008
Morphology and distribution of carbon nanostructures in a deposit produced by arc discharge in liquid nitrogen
- 1 January 2012
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 15 (6) , H182-H184
Wafer Cut Effect on Hetero-Epitaxial 3C-SiC Film for MEMS Application
In this paper we study the influence of post-growth wafer cutting of hetero-epitaxial 3C-SiC on Si substrate for 6 and 8 inches wafers. We find an increase of wafer curvature after each cut process and a correspondent variation of the Raman shift. This result, confirmed by FEM, can be explained in term of the wafer symmetry breaking and the related relaxation under modified constrains due to the cutting. The FEM analysis of the deformation state reveals a modification of the residual stress tensor which changes from a pure biaxial form to a more complicated one containing diagonal and off-diagonal components.
- 1 January 2012
- Published by The Electrochemical Society in Electrochemical and Solid-State Letters
- Vol. 15 (6) , H182-H184
Wafer Cut Effect on Hetero-Epitaxial 3C-SiC Film for MEMS Application
In this paper we study the influence of post-growth wafer cutting of hetero-epitaxial 3C-SiC on Si substrate for 6 and 8 inches wafers. We find an increase of wafer curvature after each cut process and a correspondent variation of the Raman shift. This result, confirmed by FEM, can be explained in term of the wafer symmetry breaking and the related relaxation under modified constrains due to the cutting. The FEM analysis of the deformation state reveals a modification of the residual stress tensor which changes from a pure biaxial form to a more complicated one containing diagonal and off-diagonal components.