Experimental and Numerical Analysis of the Shear Properties of Honeycomb Cores Produced Using Additive Technologies
Authors:
- Yuzhnoye State Design OfficeYOYuzhnoye State Design Office
- Ihor I. DereviankoIDIhor I. Derevianko
- A. Pidhornyi Institute of Mechanical Engineering Problems of NASUANA. Pidhornyi Institute of Mechanical Engineering Problems of NASU
- Borys V. UspenskyiBUBorys V. Uspenskyi
- Kostiantyn V. AvramovKAKostiantyn V. Avramov
- Kharkiv National University of Radio ElectronicsKEKharkiv National University of Radio Electronics
- Oleksandr F. SalenkoOSOleksandr F. Salenko
- National Technical University of Ukraine Igor Sikorsky Kyiv Polytechnic InstituteNINational Technical University of Ukraine Igor Sikorsky Kyiv Polytechnic Institute
- Iryna V. BiblikIBIryna V. Biblik
Open Access
- 30 December 2021
- journal article
- research article
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 24 (4) , 71-76
Abstract
An approach to the experimental and computational study of the shear properties of honeycomb cores (HC) produced using Fused Deposition Modeling (FDM) technology is proposed. The experimental approach is based on a new sample type for testing HCs for shear. This sample contains two HCs and three steel plates. Shear tests are carried out in the TiraTest 2300 universal tensile testing machine. The HCs are made of ULTEM 9085 and PLA with FDM technology, which is implemented in the 3D Fortus 900 system. The tests resulted in obtaining the shear properties of the HCs by averaging the stress-strain curves of five samples. As follows from the analysis of the experimental results, brittle destruction of an HC is observed. Before its destruction, the value of shear deformation for samples made of PLA was 0.0134, and for samples made of ULTEM, 0.0257. The experimental analysis was accompanied by numerical finite element (FE) modeling of shear experiments, taking into account the deformation of the equipment. With the FE modeling of the experiments, to describe the behavior of the samples, it is necessary to take into account the influence, on the measurements of the shear properties, of the equipment and the deformation of each honeycomb cell. The deformation of three plates was taken into account; the elastic properties of the adhesive joint were not taken into account. A computer model of the deformation of the HCs with equipment was built using ANSYS Design Modeler. With FE modeling, only the elastic behavior of the HCs was considered.Keywords
This publication has 13 references indexed in Scilit:
- 3D printed hierarchical honeycombs with shape integrity under large compressive deformationsMaterials & Design, 2018
- A multi-scale approach for the optimum design of sandwich plates with honeycomb core. Part I: homogenisation of core propertiesComposite Structures, 2014
- Interaction of elastic system with snap-through vibration absorberInternational Journal of Non-Linear Mechanics, 2009
- The effect of honeycomb relative density on its effective in-plane elastic moduli: An experimental studyComposite Structures, 2008
- Mechanical properties of Nomex material and Nomex honeycomb structureComposite Structures, 2007
- Effective stress-strain relations for two-dimensional cellular sandwich cores: Homogenization, material models, and propertiesApplied Mechanics Reviews, 2001
- Prediction of Elastic Properties of Sandwich Panels Using a Homogenization Computational Model1998
- Models for the elastic deformation of honeycombsComposite Structures, 1996
- A finite element study of the transverse shear in honeycomb coresInternational Journal of Solids and Structures, 1993
- The mechanics of two-dimensional cellular materialsProceedings of the Royal Society of London. A. Mathematical and Physical Sciences, 1982