Boris Uspensky
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Boris Uspensky has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Kostiantyn V. Avramov
Anatolii Pidhornyi Institute of Power Machines and Systems of the National academy of sciences of Ukraine, Kharkiv, Ukraine
25 shared publications - Maryna Chernobryvko
A. Pidhornyi Institute of Power Machines and Systems, National Academy of Science of Ukraine
8 shared publications A. Pidhornyi Institute of Mechanical Engineering Problems of NASU
6 shared publications- Ihor I. Derevianko
Yuzhnoye State Design Office
6 shared publications - Iryna V. Biblik
Anatolii Pidhornyi Institute of Power Machines and Systems of NAS of Ukraine
5 shared publications - Oleksandr Salenko
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
5 shared publications
Latest Publications
- 30 September 2026
- Published by LLP International Educational Corporation in Bulletin of Kazakh Leading Academy of Architecture and Construction
- Vol. 101 (3) , 153-170
EXPERIMENTAL VERIFICATION OF THE STRAIN-STRESS DISTRIBUTION OF A HINGED VENTILATED FACE SUBSYSTEM UNDER NONSTATIONARY LOADING
Hinged ventilated faces (HVFs) are among the most effective solutions for thermal renovation of buildings in extreme continental climates. A previous study developed a “boundary optimization” methodology for the HVF subsystem topology using the finite-element technique (FET): increasing the bracket spacing from 600 × 600 mm to 1000 × 1000 mm reduces the thermal irregularity coefficient from 8.33% to 3.0% while keeping stresses within 75% of the material’s yield point. However, experimental verification under seismic loading has been lacking, limiting the approach’s direct application in design practice. This study experimentally verifies the finite element model of an HVF subsystem under nonstationary loading, for bracket radiuses of 150 mm and 200 mm at 600 × 600 mm spacing. The novelty lies in the quantitative justification of the FE modeling strategy through direct comparison of calculated and experimental von Mises stresses and displacements, with a physical explanation of their systematic discrepancy. Tests were performed on full-scale (1:1) specimens using a uniaxial electrodynamic vibration bed, with seismic action defined by synthetic accelerograms compatible with design spectra for soil category III at seismicity of 8 and 9 (MSK-64). Deformations were measured with strain gauges and displacements with laser sensors, for four configurations under two seismic directions. The resulting deviation of 12.0-12.6% remained within the ±15% verification threshold, confirming the FE strategy’s adequacy for engineering calculations and providing an experimentally validated basis for extending the “boundary optimization” methodology to larger bracket spacings and other seismically active regions.
- 30 September 2026
- Published by LLP International Educational Corporation in Bulletin of Kazakh Leading Academy of Architecture and Construction
- Vol. 101 (3) , 153-170
EXPERIMENTAL VERIFICATION OF THE STRAIN-STRESS DISTRIBUTION OF A HINGED VENTILATED FACE SUBSYSTEM UNDER NONSTATIONARY LOADING
Hinged ventilated faces (HVFs) are among the most effective solutions for thermal renovation of buildings in extreme continental climates. A previous study developed a “boundary optimization” methodology for the HVF subsystem topology using the finite-element technique (FET): increasing the bracket spacing from 600 × 600 mm to 1000 × 1000 mm reduces the thermal irregularity coefficient from 8.33% to 3.0% while keeping stresses within 75% of the material’s yield point. However, experimental verification under seismic loading has been lacking, limiting the approach’s direct application in design practice. This study experimentally verifies the finite element model of an HVF subsystem under nonstationary loading, for bracket radiuses of 150 mm and 200 mm at 600 × 600 mm spacing. The novelty lies in the quantitative justification of the FE modeling strategy through direct comparison of calculated and experimental von Mises stresses and displacements, with a physical explanation of their systematic discrepancy. Tests were performed on full-scale (1:1) specimens using a uniaxial electrodynamic vibration bed, with seismic action defined by synthetic accelerograms compatible with design spectra for soil category III at seismicity of 8 and 9 (MSK-64). Deformations were measured with strain gauges and displacements with laser sensors, for four configurations under two seismic directions. The resulting deviation of 12.0-12.6% remained within the ±15% verification threshold, confirming the FE strategy’s adequacy for engineering calculations and providing an experimentally validated basis for extending the “boundary optimization” methodology to larger bracket spacings and other seismically active regions.
- 26 May 2026
- Published by Springer Nature
- p. 253-263
Impact on Nanocomposite Conical Shell with Isotropic Ring
- 26 May 2026
- Published by Springer Nature
- p. 253-263
Impact on Nanocomposite Conical Shell with Isotropic Ring
- Open Access
- 30 March 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 29 (1) , 6-15
Linear Vibrations of Nanotube-Reinforced Composite Conical Shell with Ring Stiffener
Linear vibrations of thin-walled structure, which consists of nanotube-reinforced conical shell and ring stiffeners, are analyzed. Ring is attached at the end of truncated conical shell. Such shell structure describes adapter of rocket. Dynamic of such structure is actual problem of aerospace engineering. Material of this shell is nanocomposite, and ring is manufactured from isotropic material. Higher order shear deformation theory for the shell and Euler-Bernoulli theory for ring stiffeners are applied. The Rayleigh-Ritz method is used to derive the equations of the structure vibrations. The potential energy of the thin-walled structure is used. This potential energy consists of potential energy of the conical shell and potential energy of the ring. It is assumed that the ring vibrates in two perpendicular planes, performs vibrations in circumference directions, and torsional vibrations occur. The least action variational principle is used. As a result, the generalized eigenvalue problem is derived. The data of eigenfrequencies calculations is verified by finite element calculations in ANSYS software.
- 30 March 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 29 (1) , 6-15
Open AccessLinear Vibrations of Nanotube-Reinforced Composite Conical Shell with Ring Stiffener
Linear vibrations of thin-walled structure, which consists of nanotube-reinforced conical shell and ring stiffeners, are analyzed. Ring is attached at the end of truncated conical shell. Such shell structure describes adapter of rocket. Dynamic of such structure is actual problem of aerospace engineering. Material of this shell is nanocomposite, and ring is manufactured from isotropic material. Higher order shear deformation theory for the shell and Euler-Bernoulli theory for ring stiffeners are applied. The Rayleigh-Ritz method is used to derive the equations of the structure vibrations. The potential energy of the thin-walled structure is used. This potential energy consists of potential energy of the conical shell and potential energy of the ring. It is assumed that the ring vibrates in two perpendicular planes, performs vibrations in circumference directions, and torsional vibrations occur. The least action variational principle is used. As a result, the generalized eigenvalue problem is derived. The data of eigenfrequencies calculations is verified by finite element calculations in ANSYS software.
- 1 October 2025
- Published by Springer Nature
- p. 140-150
Linear Vibrations of Sandwich Cylindrical Shells with Nanocomposite Layers
- 1 October 2025
- Published by Springer Nature
- p. 140-150
Linear Vibrations of Sandwich Cylindrical Shells with Nanocomposite Layers
- 20 July 2025
- Published by Springer Nature
- p. 455-466
Self-sustained Vibrations of Conical Sandwich Shell Interacting with Supersonic Gas Stream
- 20 July 2025
- Published by Springer Nature
- p. 455-466
Self-sustained Vibrations of Conical Sandwich Shell Interacting with Supersonic Gas Stream
- Open Access
- 30 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 28 (2) , 27-35
Linear Vibrations Analysis of a Composite Sandwich Conical Shell Manufactured by Additive Technologies
The sandwich conical shell with elastic honeycomb structure, which is studied in this paper, is manufactured by additive technologies and has three layers. The honeycomb structure is made of ULTEM material, and the upper and lower face layers of the structures are made of carbon fiber. Each layer of the structures is an orthotropic material and satisfies Hooke's law. Thanks to the homogenization procedure using the finite element method, we will obtain an equivalent orthotropic medium instead of the honeycomb structure. The elastic properties of this medium satisfy Hooke's law. The modified high-order shear theory is used to model the deformation of the structures. The deformations of each layer of the structures are described by five variables, which include three projections of the displacements of the median surface and two angles of rotation of the normal to the median surface. To calculate the displacements of the layers, boundary conditions for stresses and boundary conditions that describe the continuity of displacements at the layers’ boundaries are used. The vibrations of a three-layer sandwich shell are expanded into basis functions that satisfy the kinematic boundary conditions. The Rayleigh-Ritz method is used to study the vibrations. The vibration parameters of structures are calculated from the eigenvalue problem. To verify the obtained results, the natural frequencies are compared with the data of finite element modeling. As follows from the calculations, the natural frequencies obtained by the Rayleigh-Ritz method and the finite element method are close. The spectrum of natural frequencies is very dense. The minimum natural frequency of vibrations is observed when the number of waves in the circular direction is equal to one.
- 30 June 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 28 (2) , 27-35
Open AccessLinear Vibrations Analysis of a Composite Sandwich Conical Shell Manufactured by Additive Technologies
The sandwich conical shell with elastic honeycomb structure, which is studied in this paper, is manufactured by additive technologies and has three layers. The honeycomb structure is made of ULTEM material, and the upper and lower face layers of the structures are made of carbon fiber. Each layer of the structures is an orthotropic material and satisfies Hooke's law. Thanks to the homogenization procedure using the finite element method, we will obtain an equivalent orthotropic medium instead of the honeycomb structure. The elastic properties of this medium satisfy Hooke's law. The modified high-order shear theory is used to model the deformation of the structures. The deformations of each layer of the structures are described by five variables, which include three projections of the displacements of the median surface and two angles of rotation of the normal to the median surface. To calculate the displacements of the layers, boundary conditions for stresses and boundary conditions that describe the continuity of displacements at the layers’ boundaries are used. The vibrations of a three-layer sandwich shell are expanded into basis functions that satisfy the kinematic boundary conditions. The Rayleigh-Ritz method is used to study the vibrations. The vibration parameters of structures are calculated from the eigenvalue problem. To verify the obtained results, the natural frequencies are compared with the data of finite element modeling. As follows from the calculations, the natural frequencies obtained by the Rayleigh-Ritz method and the finite element method are close. The spectrum of natural frequencies is very dense. The minimum natural frequency of vibrations is observed when the number of waves in the circular direction is equal to one.
- 24 December 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 239 (8) , 774-791
Influence of cell breakings on the buckling of composite sandwich shells with FDM additively manufactured honeycomb cores
A methodology for the buckling analysis of composite cylindrical sandwich panels with cell breakings is proposed, based on finite element modeling and analysis using the commercial software ANSYS. The core of the thin-walled structure is a honeycomb made from polylactide (PLA) material and manufactured by fused deposition modeling (FDM) additive technology, and the inner and outer layers of the sandwich panels are made from carbon fiber-reinforced materials with brittle properties. The elasto-plastic properties of the honeycomb structure are obtained experimentally and taken into account. The novelty of the present article is the following. The influence of cell breakings on buckling of sandwich panels is analyzed. The longitudinal pressures of global buckling and global buckling modes of defected sandwich panels are analyzed numerically. Moreover, the local buckling of defected sandwich panels under the action of radial pressure is analyzed numerically too. The buckling pressures of the thin-walled structures with elasto-plastic honeycombs are analyzed computationally. Eight types of cell breakings with different cell breaking locations are considered.
- 24 December 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 239 (8) , 774-791
Influence of cell breakings on the buckling of composite sandwich shells with FDM additively manufactured honeycomb cores
A methodology for the buckling analysis of composite cylindrical sandwich panels with cell breakings is proposed, based on finite element modeling and analysis using the commercial software ANSYS. The core of the thin-walled structure is a honeycomb made from polylactide (PLA) material and manufactured by fused deposition modeling (FDM) additive technology, and the inner and outer layers of the sandwich panels are made from carbon fiber-reinforced materials with brittle properties. The elasto-plastic properties of the honeycomb structure are obtained experimentally and taken into account. The novelty of the present article is the following. The influence of cell breakings on buckling of sandwich panels is analyzed. The longitudinal pressures of global buckling and global buckling modes of defected sandwich panels are analyzed numerically. Moreover, the local buckling of defected sandwich panels under the action of radial pressure is analyzed numerically too. The buckling pressures of the thin-walled structures with elasto-plastic honeycombs are analyzed computationally. Eight types of cell breakings with different cell breaking locations are considered.
- Open Access
- 30 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 27 (3) , 25-33
Manufacturing Technology, Experimental and Numerical Analysis of Static Bending of Three-Layer Composite Plate with Honeycomb Structure
The use of thin-walled constructions with honeycomb structure manufactured using additive technologies has several advantages compared to the constructions manufactured using traditional technologies. First of all, this is explained by the fact that additive technologies greatly simplify the production of honeycomb structures. A technology for manufacturing a three-layer composite plate with a honeycomb structure obtained using additive technologies is proposed in the paper. PLA plastic was chosen as the material for the honeycomb structure production. Printing was carried out using a "Delta" printer with parallel kinematic chains using FDM technologies. The printing temperature was 215 °C, table temperature – 60 °C. A fundamentally new scheme of an experimental plant for studying the bending of a three-layer plate is proposed. The aim of the research is to conduct tests of samples of a three-layer honeycomb panel for static bending when one edge of the sample is rigidly pinched. For the tests, a certified TiraTest 2300 universal testing machine (UTM), which allows to perform tensile and compression tests at a given traverse speed and measure the load with a relative error of 1%, was used. The UTM allows to load the sample and measure the load and displacement of the traverse. A sixteen-channel strain gauge station is used to measure the surface deformations of the housings. Transverse displacements of a three-layer plate were obtained as experimental data. The bending of the three-layer plate is modeled in the commercial package ANSYS. The results of experimental and numerical analysis coincide well.
- 30 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Journal of Mechanical Engineering
- Vol. 27 (3) , 25-33
Open AccessManufacturing Technology, Experimental and Numerical Analysis of Static Bending of Three-Layer Composite Plate with Honeycomb Structure
The use of thin-walled constructions with honeycomb structure manufactured using additive technologies has several advantages compared to the constructions manufactured using traditional technologies. First of all, this is explained by the fact that additive technologies greatly simplify the production of honeycomb structures. A technology for manufacturing a three-layer composite plate with a honeycomb structure obtained using additive technologies is proposed in the paper. PLA plastic was chosen as the material for the honeycomb structure production. Printing was carried out using a "Delta" printer with parallel kinematic chains using FDM technologies. The printing temperature was 215 °C, table temperature – 60 °C. A fundamentally new scheme of an experimental plant for studying the bending of a three-layer plate is proposed. The aim of the research is to conduct tests of samples of a three-layer honeycomb panel for static bending when one edge of the sample is rigidly pinched. For the tests, a certified TiraTest 2300 universal testing machine (UTM), which allows to perform tensile and compression tests at a given traverse speed and measure the load with a relative error of 1%, was used. The UTM allows to load the sample and measure the load and displacement of the traverse. A sixteen-channel strain gauge station is used to measure the surface deformations of the housings. Transverse displacements of a three-layer plate were obtained as experimental data. The bending of the three-layer plate is modeled in the commercial package ANSYS. The results of experimental and numerical analysis coincide well.
- Open Access
- 22 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (5) , 1790
Finite-Element Modeling of the Dynamic Behavior of a Crack-like Defect in an Internally Pressurized Thin-Walled Steel Cylinder
This article presents one part of a study on the dynamic deformation and fracture of sections of steel gas pipelines with an external crack-like defect under the action of internal pressure. This work was performed on the basis of finite-element simulations using a cylindrical shell model executed by ANSYS-19.2 on the example of the section of the steel gas pipeline “Beineu–Bozoy–Shymkent” in the Republic of Kazakhstan. The propagation of the incipient crack-like defect along the pipeline and the resulting dynamic fracture in its tip area were investigated. The options of pipeline loading by working and critical internal pressure were both considered. It was found that, within the time of 1.0 ms, the formed crack expanded in the circumferential direction up to the maximum value, which depended on the value of the internal pressure. A further growth of cracks occurred along the longitudinal direction. At the operating pressure, the initial length of the crack increased by a factor of 5.6, while the equivalent stresses increased by a factor of 1.53 within 3.5 ms. Within the time of 3.75 ms, the equivalent stresses stopped growing due to the gas decompression. Specifically, there was a stop to the crack growth along the longitudinal direction. Vice versa, at the maximum pressure, the pipeline fracture did not change qualitatively, while at the time of the process, it decreased up to 3.5 ms. The finite-element results of the stress–strain state and pipeline fracture in the crack tip area at the working pressure showed that, within the time of 1.0 ms, the distance between the crack walls reached 23 mm at the free edge. Conversely, within the time periods of 2.25 and 3.5 ms, it increased two and three times, respectively. The crack elongation in the longitudinal direction occurred 5.8 times with time. Together, within the time of 3.5 ms, the equivalent stresses increased twice, after which the growth of the crack stopped due to the gas decompression. Moreover, studies on the growth of the crack-like defect in its tip area at the maximum pressure showed that additional considerations on the pressure on the crack edges led to an increment of 3.6% of the crack length. The results of this work can be used for the development of measurements for operating gas pipelines in the field of structural reinforcement.
- 22 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (5) , 1790
Open AccessFinite-Element Modeling of the Dynamic Behavior of a Crack-like Defect in an Internally Pressurized Thin-Walled Steel Cylinder
This article presents one part of a study on the dynamic deformation and fracture of sections of steel gas pipelines with an external crack-like defect under the action of internal pressure. This work was performed on the basis of finite-element simulations using a cylindrical shell model executed by ANSYS-19.2 on the example of the section of the steel gas pipeline “Beineu–Bozoy–Shymkent” in the Republic of Kazakhstan. The propagation of the incipient crack-like defect along the pipeline and the resulting dynamic fracture in its tip area were investigated. The options of pipeline loading by working and critical internal pressure were both considered. It was found that, within the time of 1.0 ms, the formed crack expanded in the circumferential direction up to the maximum value, which depended on the value of the internal pressure. A further growth of cracks occurred along the longitudinal direction. At the operating pressure, the initial length of the crack increased by a factor of 5.6, while the equivalent stresses increased by a factor of 1.53 within 3.5 ms. Within the time of 3.75 ms, the equivalent stresses stopped growing due to the gas decompression. Specifically, there was a stop to the crack growth along the longitudinal direction. Vice versa, at the maximum pressure, the pipeline fracture did not change qualitatively, while at the time of the process, it decreased up to 3.5 ms. The finite-element results of the stress–strain state and pipeline fracture in the crack tip area at the working pressure showed that, within the time of 1.0 ms, the distance between the crack walls reached 23 mm at the free edge. Conversely, within the time periods of 2.25 and 3.5 ms, it increased two and three times, respectively. The crack elongation in the longitudinal direction occurred 5.8 times with time. Together, within the time of 3.5 ms, the equivalent stresses increased twice, after which the growth of the crack stopped due to the gas decompression. Moreover, studies on the growth of the crack-like defect in its tip area at the maximum pressure showed that additional considerations on the pressure on the crack edges led to an increment of 3.6% of the crack length. The results of this work can be used for the development of measurements for operating gas pipelines in the field of structural reinforcement.