Ultrafast thin-disk multipass laser amplifier scheme avoiding misalignment induced by natural convection of the ambient air
Open Access
- 11 September 2019
- journal article
- research article
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 58 (09) , 096102-8
Abstract
Laser material processing with ultrashort laser pulses has been a rapidly growing field in recent years. Several promising applications demand high average power in order to increase productivity as well as for high pulse energies to allow for multispot parallel processing.1 In particular, processing at low repetition rates in the range of several tens of kilohertz is promising since thermal damage induced by heat accumulation caused by consecutive pulses can be effectively avoided.2,3 By now, several laser architectures are suited to deliver average power in the kW range.4–8 Due to the completely passive approach, the low number of transmissive optics, and the possibility to scale the beam diameter to reduce nonlinear effects, the thin-disk based multipass amplifier (TDMPA) scheme is a promising architecture to reach very high output power and energy.9–12 However, due to the deflection of the laser beam, which is caused by the heated ambient air in front of the surface of the pumped laser crystal by natural convection (referred to as “air-wedge” in the following), the output power that can be achieved in the TDMPA architecture is limited to a few hundreds of watts, if no compensating element is used, such as introduced in Ref. 11. In contrast to thin-disk based regenerative amplifiers, which are based on a cavity and therefore can be realigned with the end mirror to compensate for pump power-dependent misalignment, the realignment of a TDMPA during high power operation is particularly critical due to the long propagation length of the signal beam in the amplifier. To maintain the alignment of the beam path, the TDMPA architecture, therefore, relies on passive compensation strategies. For this reason, state-of-the-art TDMPAs require a retroreflecting mirror pair (RMP) in order to minimize the deflection of the laser beam caused by the air-wedge effect.11 But even with the RMP, residual pump power-dependent air-wedge induced misalignment is usually observed. Other approaches, such as the operation in vacuum or a helium atmosphere, demonstrated to reduce thermo-optical wavefront aberrations in an oscillator and should also be applicable to TDMPAs but increase the complexity of the overall system.13,14 For laser resonators operating in continuous wave, a passive compensation based on a grating end mirror in Littrow configuration has been successfully demonstrated.15 But as this concept requires the feedback of a resonator to allow for a shift in the oscillating wavelength to correct for an air-wedge induced change of the angle of incidence on the grating, this approach cannot be applied to TDMPAs. Another common approach to reduce the pump power-dependent misalignment caused by the air-wedge effect is the reduction of the temperature of the laser crystal by reducing the heat generated during the pumping process of the laser active medium. This is accomplished by a reduction of the quantum defect by pumping directly in the upper laser level, which is usually referred to as “zero phonon line pumping (ZPL).”11,14,16–19 For Yb:YAG-based systems, the pump spectrum, in this case, needs to be locked to 969 nm (∼3 nm FWHM) instead of 940 nm (∼15 nm FWHM).17 Although ZPL significantly reduces the heat load, it can neither completely avoid heating of the laser crystal nor the resulting thermally induced effects.Keywords
Funding Information
- European Union (687613)
This publication has 18 references indexed in Scilit:
- Highly stable, 54mJ Yb-InnoSlab laser platform at 05kW average powerOptics Express, 2017
- 1 kW, 200 mJ picosecond thin-disk laser systemOptics Letters, 2017
- Processing constraints resulting from heat accumulation during pulsed and repetitive laser materials processingOptics Express, 2017
- 1 kW 1 mJ eight-channel ultrafast fiber laserOptics Letters, 2016
- Second Generation Thin-Disk Multipass Amplifier Delivering Picosecond Pulses with 2 kW of Average Output Power2016
- Ultrafast thin-disk multipass laser amplifier delivering 14 kW (47 mJ, 1030 nm) average power converted to 820 W at 515 nm and 234 W at 343 nmOptics Express, 2015
- High-quality processing of CFRP with a 1.1-kW picosecond laserApplied Physics A, 2015
- Heat accumulation during pulsed laser materials processingOptics Express, 2014
- Compact diode-pumped 11 kW Yb:YAG Innoslab femtosecond amplifierOptics Letters, 2010
- Femtosecond fiber CPA system emitting 830 W average output powerOptics Letters, 2010