Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy
Open Access
- 14 August 2025
- journal article
- research article
- Published by MDPI AG in Micromachines
- Vol. 16 (8) , 936
Abstract
Titanium alloys (Ti-6Al-4V) are widely used in the aerospace field. However, as a typical difficult-to-machine material, titanium alloys have a low thermal conductivity, a high chemical activity, and a significant adiabatic shear effect. In conventional milling (CM), the temperature in the cutting zone rises sharply, leading to tool adhesion, rapid wear, and damage to the workpiece surface. This article systematically investigated the influence of process parameters on the surface roughness, cutting force, and cutting temperature in the ultrasonic-vibration-assisted milling (UAM) process of titanium alloys, based on which multi-objective optimization process of the milling process parameters was conducted, by utilizing the grey relational analysis method. An orthogonal experiment with four factors and four levels was conducted. The effects of various process parameters on the surface roughness, cutting force, and cutting temperature were systematically analyzed for both UAM and CM. The grey relational analysis method was employed to transform the optimization problem of multiple process target parameters into a single-objective grey relational degree optimization problem. The optimized parameter combination was as follows: an ultrasonic amplitude of 6 μm, a spindle speed of 6000 rpm, a cutting depth of 0.20 mm, and a feed rate of 200 mm/min. The experimental results indicated that the surface roughness Sa was 0.268 μm, the cutting temperature was 255.39 °C, the cutting force in the X direction (FX) was 5.2 N, the cutting force in the Y direction (FY) was 7.9 N, and the cutting force in the Z direction (FZ) was 6.4 N. The optimization scheme significantly improved the machining quality and reduced both the cutting forces and the cutting temperature.Keywords
Funding Information
- Tianjin Science and Technology Plan Project (24PTLYHZ00030, KLHCMT202407)
- Open Project of Key Laboratory of High-end CNC Machine Tool of Genertec (24PTLYHZ00030, KLHCMT202407)
This publication has 23 references indexed in Scilit:
- Study on Fretting Wear Behavior of Titanium Alloys Sliding Against Various Friction Pair Materials at Room Temperature for Aero-Engine ApplicationsJournal of Bio- and Tribo-Corrosion, 2025
- Unraveling the influence of vibrations on material removal and surface quality in longitudinal ultrasonic vibration–assisted milling of Ti2AlNb intermetallic alloyThe International Journal of Advanced Manufacturing Technology, 2025
- A grey relational-Taguchi analysis on high-speed milling of duplex and super duplex stainless steels used in chemical tankersInternational Journal on Interactive Design and Manufacturing (IJIDeM), 2024
- Machinability of elliptical ultrasonic vibration milling γ-TiAl: Chip formation, edge breakage, and subsurface layer deformationChinese Journal of Aeronautics, 2024
- Design and surface analysis in large-amplitude longitudinal ultrasonic vibration-assisted milling of TC4 titanium alloy under dry conditionsThe International Journal of Advanced Manufacturing Technology, 2024
- Optimization of process parameters for minimizing the temperature field of high-speed milling of titanium alloy thin-walled partsInternational Journal on Interactive Design and Manufacturing (IJIDeM), 2024
- Research on the machining mechanism of AISI 304 ultrasonic vibration assisted grindingApplied Acoustics, 2023
- Effects of rotary ultrasonic elliptical machining for side milling on the surface integrity of Ti-6Al-4VThe International Journal of Advanced Manufacturing Technology, 2018
- Effects of Ultrasonics-Assisted Face Milling on Surface Integrity and Fatigue Life of Ni-Alloy 718Journal of Materials Engineering and Performance, 2016
- Using two-dimensional vibration cutting for micro-millingInternational Journal of Machine Tools and Manufacture, 2006