Shengming Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shengming Zhou has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Gaofeng Hu
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
4 shared publications - Min Zhang
School of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
3 shared publications - Yanjie Lu
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
3 shared publications - Fenghui Zhang
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
2 shared publications - Guangjun Chen
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
2 shared publications - Junti Lu
School of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
2 shared publications
Latest Publications
- Open Access
- 14 August 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (8) , 936
Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy
Titanium alloys (Ti-6Al-4V) are widely used in the aerospace field. However, as a typical difficult-to-machine material, titanium alloys have a low thermal conductivity, a high chemical activity, and a significant adiabatic shear effect. In conventional milling (CM), the temperature in the cutting zone rises sharply, leading to tool adhesion, rapid wear, and damage to the workpiece surface. This article systematically investigated the influence of process parameters on the surface roughness, cutting force, and cutting temperature in the ultrasonic-vibration-assisted milling (UAM) process of titanium alloys, based on which multi-objective optimization process of the milling process parameters was conducted, by utilizing the grey relational analysis method. An orthogonal experiment with four factors and four levels was conducted. The effects of various process parameters on the surface roughness, cutting force, and cutting temperature were systematically analyzed for both UAM and CM. The grey relational analysis method was employed to transform the optimization problem of multiple process target parameters into a single-objective grey relational degree optimization problem. The optimized parameter combination was as follows: an ultrasonic amplitude of 6 μm, a spindle speed of 6000 rpm, a cutting depth of 0.20 mm, and a feed rate of 200 mm/min. The experimental results indicated that the surface roughness Sa was 0.268 μm, the cutting temperature was 255.39 °C, the cutting force in the X direction (FX) was 5.2 N, the cutting force in the Y direction (FY) was 7.9 N, and the cutting force in the Z direction (FZ) was 6.4 N. The optimization scheme significantly improved the machining quality and reduced both the cutting forces and the cutting temperature.
- 14 August 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (8) , 936
Open AccessMulti-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy
Titanium alloys (Ti-6Al-4V) are widely used in the aerospace field. However, as a typical difficult-to-machine material, titanium alloys have a low thermal conductivity, a high chemical activity, and a significant adiabatic shear effect. In conventional milling (CM), the temperature in the cutting zone rises sharply, leading to tool adhesion, rapid wear, and damage to the workpiece surface. This article systematically investigated the influence of process parameters on the surface roughness, cutting force, and cutting temperature in the ultrasonic-vibration-assisted milling (UAM) process of titanium alloys, based on which multi-objective optimization process of the milling process parameters was conducted, by utilizing the grey relational analysis method. An orthogonal experiment with four factors and four levels was conducted. The effects of various process parameters on the surface roughness, cutting force, and cutting temperature were systematically analyzed for both UAM and CM. The grey relational analysis method was employed to transform the optimization problem of multiple process target parameters into a single-objective grey relational degree optimization problem. The optimized parameter combination was as follows: an ultrasonic amplitude of 6 μm, a spindle speed of 6000 rpm, a cutting depth of 0.20 mm, and a feed rate of 200 mm/min. The experimental results indicated that the surface roughness Sa was 0.268 μm, the cutting temperature was 255.39 °C, the cutting force in the X direction (FX) was 5.2 N, the cutting force in the Y direction (FY) was 7.9 N, and the cutting force in the Z direction (FZ) was 6.4 N. The optimization scheme significantly improved the machining quality and reduced both the cutting forces and the cutting temperature.
- Open Access
- 22 June 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (7) , 728
Experimental Study on Surface Integrity of Nickel-Based Superalloy in Ultrasonic Elliptical Vibration Cutting
Nickel-based superalloys, renowned for their exceptional high-temperature strength, oxidation resistance, and corrosion resistance, have become essential materials in the aerospace, defense, and nuclear industries. However, due to their poor machinability, common cutting processes often result in poor surface quality, difficulties in chip breaking, and significant tool wear. This study investigates the surface integrity of nickel-based superalloys during ultrasonic elliptical vibration cutting. The effects of various process parameters on the surface roughness, residual stress, and microhardness are systematically analyzed. The results indicate that under ultrasonic elliptical vibration cutting conditions, the surface roughness of the workpiece increases with the ultrasonic amplitude, cutting depth, and feed rate. It initially decreases and then increases with cutting speed, and decreases with an increase in the tool tip radius. The post-cutting residual stress in the nickel-based superalloy decreases with higher cutting speed and ultrasonic amplitude, but increases with greater cutting depth and tool tip radius. The surface microhardness increases with the cutting speed up to a point, after which it decreases, while it significantly increases with a higher ultrasonic amplitude, feed rate, and cutting depth. A comparative experiment was conducted between ultrasonic elliptical vibration and conventional cutting. The research results showed that when the cutting depth was 2 µm, the surface roughness and wear decreased by 19% and 53%, respectively, and the residual compressive stress and microhardness increased by 44% and 21%, respectively. This further verified the significant advantages of ultrasonic elliptical vibration cutting in optimizing machining performance.
- 22 June 2025
- Published by MDPI AG in Micromachines
- Vol. 16 (7) , 728
Open AccessExperimental Study on Surface Integrity of Nickel-Based Superalloy in Ultrasonic Elliptical Vibration Cutting
Nickel-based superalloys, renowned for their exceptional high-temperature strength, oxidation resistance, and corrosion resistance, have become essential materials in the aerospace, defense, and nuclear industries. However, due to their poor machinability, common cutting processes often result in poor surface quality, difficulties in chip breaking, and significant tool wear. This study investigates the surface integrity of nickel-based superalloys during ultrasonic elliptical vibration cutting. The effects of various process parameters on the surface roughness, residual stress, and microhardness are systematically analyzed. The results indicate that under ultrasonic elliptical vibration cutting conditions, the surface roughness of the workpiece increases with the ultrasonic amplitude, cutting depth, and feed rate. It initially decreases and then increases with cutting speed, and decreases with an increase in the tool tip radius. The post-cutting residual stress in the nickel-based superalloy decreases with higher cutting speed and ultrasonic amplitude, but increases with greater cutting depth and tool tip radius. The surface microhardness increases with the cutting speed up to a point, after which it decreases, while it significantly increases with a higher ultrasonic amplitude, feed rate, and cutting depth. A comparative experiment was conducted between ultrasonic elliptical vibration and conventional cutting. The research results showed that when the cutting depth was 2 µm, the surface roughness and wear decreased by 19% and 53%, respectively, and the residual compressive stress and microhardness increased by 44% and 21%, respectively. This further verified the significant advantages of ultrasonic elliptical vibration cutting in optimizing machining performance.
- Open Access
- 25 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5515
An Experiment Study on Surface Topography of GH4169 Assisted by Ultrasonic Elliptical Vibration Ultra-Precision Turning
Nickel-based superalloys (GH4169) are a typical difficult-to-machine material with poor thermal conductivity and severe work hardening. They are also prone to poor surface quality, severe tool wear, and poor machinability, which affect their performance. In this paper, an experimental study of GH4169 ultrasonic elliptical vibratory ultra-precision cutting was carried out. The experimental results show that ultrasonic elliptical vibratory cutting (UEVC) significantly reduces surface roughness and improves surface quality compared to conventional cutting (CC). The effects of cutting parameters such as cutting speed, feed rate, cutting depth, ultrasonic amplitude, and tool nose radius on the surface roughness of GH4169 workpieces were further investigated in UEVC. Based on the analysis of the experimental data, the optimal combination of parameters for GH4169 ultrasonic elliptical vibration ultra-precision cutting was determined: cutting speed of 3 m/min, feed rate of 16 μm/rev, cutting depth of 2 μm, ultrasonic amplitude of Ay = 3.0 μm, Az = 0.8 μm, and a tool nose radius of 0.8 mm. This parameter combination improves the machining quality of GH4169 and provides a valuable reference for the subsequent development of ultrasonic elliptical vibratory cutting for other difficult-to-machine materials.
- 25 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5515
Open AccessAn Experiment Study on Surface Topography of GH4169 Assisted by Ultrasonic Elliptical Vibration Ultra-Precision Turning
Nickel-based superalloys (GH4169) are a typical difficult-to-machine material with poor thermal conductivity and severe work hardening. They are also prone to poor surface quality, severe tool wear, and poor machinability, which affect their performance. In this paper, an experimental study of GH4169 ultrasonic elliptical vibratory ultra-precision cutting was carried out. The experimental results show that ultrasonic elliptical vibratory cutting (UEVC) significantly reduces surface roughness and improves surface quality compared to conventional cutting (CC). The effects of cutting parameters such as cutting speed, feed rate, cutting depth, ultrasonic amplitude, and tool nose radius on the surface roughness of GH4169 workpieces were further investigated in UEVC. Based on the analysis of the experimental data, the optimal combination of parameters for GH4169 ultrasonic elliptical vibration ultra-precision cutting was determined: cutting speed of 3 m/min, feed rate of 16 μm/rev, cutting depth of 2 μm, ultrasonic amplitude of Ay = 3.0 μm, Az = 0.8 μm, and a tool nose radius of 0.8 mm. This parameter combination improves the machining quality of GH4169 and provides a valuable reference for the subsequent development of ultrasonic elliptical vibratory cutting for other difficult-to-machine materials.
- Open Access
Developmental and Experimental Study on a Double-Excitation Ultrasonic Elliptical Vibration-Assisted Cutting Device
Ultrasonic elliptical vibration-assisted cutting (UEVC) has been successfully applied in the precision and ultra-precision machining of hard and brittle materials due to its advantages of a low cutting force and minimal tool wear. This study developed a novel double-excitation ultrasonic elliptic vibration-assisted cutting (D-UEVC) device by coupling ultrasonic vibrations in orthogonal dual paths. A two-degree-of-freedom vibration system of the D-UEVC was modeled, form which the elliptical trajectory of the end under different phase angle φ values was derived. The initial dimensions of the D-UEVC device were obtained through theoretical calculations. Subsequently, with the aid of finite element analysis methods, structural dynamic analysis of the device was conducted to obtain the elliptical vibration trajectory under different phase differences of the excitation source. In order to verify the cutting trajectory and cutting performance of the D-UEVC device, a prototype of the device was developed, and a series of vibration performance tests as well as the Inconel 718 cutting experiment were conducted. The experimental results illustrated that the D-UEVC device can achieve the elliptical vibration trajectory at the tool tip with a resonant frequency of 36.5 KHz. The adjustable elliptical vibration trajectories covered a range of ±4 μm in the axial and radial directions. Compared with the surface roughness Ra = 0.36 μm under the conventional cutting, the surface roughness of Inconel 718 under D-UEVC was Ra = 0.215 μm. Thus, the surface quality can be significant improved by utilizing the D-UEVC device.
Open AccessDevelopmental and Experimental Study on a Double-Excitation Ultrasonic Elliptical Vibration-Assisted Cutting Device
Ultrasonic elliptical vibration-assisted cutting (UEVC) has been successfully applied in the precision and ultra-precision machining of hard and brittle materials due to its advantages of a low cutting force and minimal tool wear. This study developed a novel double-excitation ultrasonic elliptic vibration-assisted cutting (D-UEVC) device by coupling ultrasonic vibrations in orthogonal dual paths. A two-degree-of-freedom vibration system of the D-UEVC was modeled, form which the elliptical trajectory of the end under different phase angle φ values was derived. The initial dimensions of the D-UEVC device were obtained through theoretical calculations. Subsequently, with the aid of finite element analysis methods, structural dynamic analysis of the device was conducted to obtain the elliptical vibration trajectory under different phase differences of the excitation source. In order to verify the cutting trajectory and cutting performance of the D-UEVC device, a prototype of the device was developed, and a series of vibration performance tests as well as the Inconel 718 cutting experiment were conducted. The experimental results illustrated that the D-UEVC device can achieve the elliptical vibration trajectory at the tool tip with a resonant frequency of 36.5 KHz. The adjustable elliptical vibration trajectories covered a range of ±4 μm in the axial and radial directions. Compared with the surface roughness Ra = 0.36 μm under the conventional cutting, the surface roughness of Inconel 718 under D-UEVC was Ra = 0.215 μm. Thus, the surface quality can be significant improved by utilizing the D-UEVC device.