Development and Performance Measurement of Oil-Free Turbocharger Supported on Gas Foil Bearings
- 4 January 2012
- journal article
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (3) , 032506
Abstract
This paper present the development of an oil-free turbocharger (TC) supported on gas foil bearings (GFBs) and its performance evaluation in a test rig driven by a diesel vehicle engine (EG). The rotor-bearing system was designed via a rotordynamic analysis with dynamic force coefficients derived from the analysis of the GFBs. The developed oil-free TC was designed using a hollow rotor with a radial turbine at one end and a compressor wheel at the other end, a center housing with journal and thrust GFBs, and turbine and compressor casings. Preliminary tests driven by pressurized shop air at room temperature demonstrated relatively stable operation up to a TC speed of 90,000 rpm, accompanied by a dominant synchronous motion of ∼20 μm and small subsynchronous motions of less than 2 μm at the higher end of the speed range. Under realistic operating conditions with a diesel vehicle engine at a maximum TC speed of 136,000 rpm and a maximum EG speed of 3140 rpm, EG and TC speeds and gas flow properties were measured. The measured time responses of the TC speed and the turbine inlet pressure demonstrated time delays of ∼3.9 and ∼1.3 s from that of the EG speed during consecutive stepwise EG speed changes, implying the GFB friction and rotor inertia led to time delays of ∼2.6 s. The measured pressures and temperatures showed trends following second-order polynomials against EG speed. Regarding TC efficiency, 4.3 kW of mechanical power was supplied by the turbine and 3.3 kW was consumed by the compressor at the top speed of 136,000 rpm, and the power loss reached 22% of the turbine power. Furthermore, the estimated GFB power losses from the GFB analysis were approximately 25% of the total power loss at higher speeds, indicating the remainder of the power loss resulted from heat transfer from the exhaust gas to the surrounding solid structures. Incidentally, as the TC speed was increased from 45,000 to 136,000 rpm, the estimated turbine inlet power increased from 19 to 79 kW, the compressor exit power increased from 7 to 26 kW, and the TC output mass flow rate from the compressor increased from 21 to 74 g/s. The average TC compressor exit power was estimated at ∼34% of the turbine inlet power over this range.Keywords
This publication has 18 references indexed in Scilit:
- A Systems Approach to the Solid Lubrication of Foil Air Bearings for Oil-Free TurbomachineryJournal of Tribology, 2004
- The Role of Radial Clearance on the Performance of Foil Air BearingsTribology Transactions, 2002
- Load Capacity Estimation of Foil Air Journal Bearings for Oil-Free Turbomachinery ApplicationsTribology Transactions, 2000
- Performance and Durability of High Temperature Foil Air Bearings for Oil-Free TurbomachineryTribology Transactions, 2000
- Analysis of Gas Lubricated Foil Thrust Bearings Using Coupled Finite Element and Finite Difference MethodsJournal of Tribology, 1999
- Rotordynamics and Design Methods of an Oil-Free Turbocharger©Tribology Transactions, 1999
- Advancements in the Performance of Aerodynamic Foil Journal Bearings: High Speed and Load CapabilityJournal of Tribology, 1994
- Coulomb Friction Damping Effects in Elastically Supported Gas Foil Bearings©Tribology Transactions, 1994
- Analysis of Gas-Lubricated Foil Journal BearingsJournal of Lubrication Technology, 1983
- Modern Developments in Lubrication MechanicsJournal of Lubrication Technology, 1977