Kyuho Sim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kyuho Sim has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Tae Ho Kim
Energy Mechanics Research Center, Korea Institute of Science and Technology, 39-1 Hawolgok-dong, Songbuk-gu, Seoul 136-791, Korea
2 shared publications - Yong-Bok Lee
Korea Institute of Science and Technology
2 shared publications - Dong-Jin Park
Korea Institute of Science and Technology, Energy Mechanics Center, Seoul, Republic of Korea
1 shared publication - Jin Woo Song
Energy Mechanics Center, Korea Institute of Science and Technology, 39-1 Hawolgok-dong, Songbuk-gu, 136-791 Seoul, South Korea
1 shared publication
Latest Publications
- 4 January 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (3) , 032506
Development and Performance Measurement of Oil-Free Turbocharger Supported on Gas Foil Bearings
This paper present the development of an oil-free turbocharger (TC) supported on gas foil bearings (GFBs) and its performance evaluation in a test rig driven by a diesel vehicle engine (EG). The rotor-bearing system was designed via a rotordynamic analysis with dynamic force coefficients derived from the analysis of the GFBs. The developed oil-free TC was designed using a hollow rotor with a radial turbine at one end and a compressor wheel at the other end, a center housing with journal and thrust GFBs, and turbine and compressor casings. Preliminary tests driven by pressurized shop air at room temperature demonstrated relatively stable operation up to a TC speed of 90,000 rpm, accompanied by a dominant synchronous motion of ∼20 μm and small subsynchronous motions of less than 2 μm at the higher end of the speed range. Under realistic operating conditions with a diesel vehicle engine at a maximum TC speed of 136,000 rpm and a maximum EG speed of 3140 rpm, EG and TC speeds and gas flow properties were measured. The measured time responses of the TC speed and the turbine inlet pressure demonstrated time delays of ∼3.9 and ∼1.3 s from that of the EG speed during consecutive stepwise EG speed changes, implying the GFB friction and rotor inertia led to time delays of ∼2.6 s. The measured pressures and temperatures showed trends following second-order polynomials against EG speed. Regarding TC efficiency, 4.3 kW of mechanical power was supplied by the turbine and 3.3 kW was consumed by the compressor at the top speed of 136,000 rpm, and the power loss reached 22% of the turbine power. Furthermore, the estimated GFB power losses from the GFB analysis were approximately 25% of the total power loss at higher speeds, indicating the remainder of the power loss resulted from heat transfer from the exhaust gas to the surrounding solid structures. Incidentally, as the TC speed was increased from 45,000 to 136,000 rpm, the estimated turbine inlet power increased from 19 to 79 kW, the compressor exit power increased from 7 to 26 kW, and the TC output mass flow rate from the compressor increased from 21 to 74 g/s. The average TC compressor exit power was estimated at ∼34% of the turbine inlet power over this range.
- 4 January 2012
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (3) , 032506
Development and Performance Measurement of Oil-Free Turbocharger Supported on Gas Foil Bearings
This paper present the development of an oil-free turbocharger (TC) supported on gas foil bearings (GFBs) and its performance evaluation in a test rig driven by a diesel vehicle engine (EG). The rotor-bearing system was designed via a rotordynamic analysis with dynamic force coefficients derived from the analysis of the GFBs. The developed oil-free TC was designed using a hollow rotor with a radial turbine at one end and a compressor wheel at the other end, a center housing with journal and thrust GFBs, and turbine and compressor casings. Preliminary tests driven by pressurized shop air at room temperature demonstrated relatively stable operation up to a TC speed of 90,000 rpm, accompanied by a dominant synchronous motion of ∼20 μm and small subsynchronous motions of less than 2 μm at the higher end of the speed range. Under realistic operating conditions with a diesel vehicle engine at a maximum TC speed of 136,000 rpm and a maximum EG speed of 3140 rpm, EG and TC speeds and gas flow properties were measured. The measured time responses of the TC speed and the turbine inlet pressure demonstrated time delays of ∼3.9 and ∼1.3 s from that of the EG speed during consecutive stepwise EG speed changes, implying the GFB friction and rotor inertia led to time delays of ∼2.6 s. The measured pressures and temperatures showed trends following second-order polynomials against EG speed. Regarding TC efficiency, 4.3 kW of mechanical power was supplied by the turbine and 3.3 kW was consumed by the compressor at the top speed of 136,000 rpm, and the power loss reached 22% of the turbine power. Furthermore, the estimated GFB power losses from the GFB analysis were approximately 25% of the total power loss at higher speeds, indicating the remainder of the power loss resulted from heat transfer from the exhaust gas to the surrounding solid structures. Incidentally, as the TC speed was increased from 45,000 to 136,000 rpm, the estimated turbine inlet power increased from 19 to 79 kW, the compressor exit power increased from 7 to 26 kW, and the TC output mass flow rate from the compressor increased from 21 to 74 g/s. The average TC compressor exit power was estimated at ∼34% of the turbine inlet power over this range.
- 8 December 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (2) , 024501
Thermal Performance Measurement of a Bump Type Gas Foil Bearing Floating on a Hollow Shaft for Increasing Rotating Speed and Static Load
Identifying thermal characteristics of gas foil bearings (GFBs) provides an insight for successful implementation into high speed oil-free turbomachinery. The paper presents temperature measurements of a bump type GFB floating on a hollow shaft for various operating conditions. Two angular ball bearings support the hollow shaft at one end (right), and the other end (left) is free. Test GFB has the outer diameter of 100 mm and the axial length of 45 mm, and the hollow shaft has the outer and inner diameters of 60 mm and 40 mm, respectively. An electric motor drives the hollow shaft using a spline coupling connection. A mechanical loading device provides static loads on test GFB upward via a metal wire, and a strain gauge type load cell placed in the middle of the wire indicates the applied loads. During experiments for shaft speeds of 5 krpm, 10 krpm, and 15 krpm and with static loads of 58.9 N (6 kgf), 78.5 N (8 kgf), and 98.1 N (10 kgf), twelve thermocouples measure the outer surface temperatures of test GFB at four angular locations of 45 deg, 135 deg, 215 deg, and 315 deg, with an origin at the top foil free end, and three axial locations of bearing centerline and both side edges at each angle. Two infrared thermometers measure the outer surface temperature of the hollow shaft at free and supported ends close to test GFB. Test results show that GFB temperatures increase as the shaft speed increases and as the static load increases, with higher temperatures in the loaded zone (135 deg and 215 deg) than those in the unloaded zone (45 deg and 315 deg). In general, the recorded temperatures are highest at 225 deg where a highest hydrodynamic pressure is expected to build up. Measured temperatures at the bearing centerline are higher than those at the side edges, as expected. In addition, large thermal gradients are recorded in the hollow shaft along the axial direction with higher temperatures at the supported end. The axial thermal gradient of the shaft is thought to cause higher temperatures at the bearing right edge facing the ball bearing support than those at the left edge. The paper presents test data along with detailed test GFB/shaft geometries and material properties.
- 8 December 2011
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 134 (2) , 024501
Thermal Performance Measurement of a Bump Type Gas Foil Bearing Floating on a Hollow Shaft for Increasing Rotating Speed and Static Load
Identifying thermal characteristics of gas foil bearings (GFBs) provides an insight for successful implementation into high speed oil-free turbomachinery. The paper presents temperature measurements of a bump type GFB floating on a hollow shaft for various operating conditions. Two angular ball bearings support the hollow shaft at one end (right), and the other end (left) is free. Test GFB has the outer diameter of 100 mm and the axial length of 45 mm, and the hollow shaft has the outer and inner diameters of 60 mm and 40 mm, respectively. An electric motor drives the hollow shaft using a spline coupling connection. A mechanical loading device provides static loads on test GFB upward via a metal wire, and a strain gauge type load cell placed in the middle of the wire indicates the applied loads. During experiments for shaft speeds of 5 krpm, 10 krpm, and 15 krpm and with static loads of 58.9 N (6 kgf), 78.5 N (8 kgf), and 98.1 N (10 kgf), twelve thermocouples measure the outer surface temperatures of test GFB at four angular locations of 45 deg, 135 deg, 215 deg, and 315 deg, with an origin at the top foil free end, and three axial locations of bearing centerline and both side edges at each angle. Two infrared thermometers measure the outer surface temperature of the hollow shaft at free and supported ends close to test GFB. Test results show that GFB temperatures increase as the shaft speed increases and as the static load increases, with higher temperatures in the loaded zone (135 deg and 215 deg) than those in the unloaded zone (45 deg and 315 deg). In general, the recorded temperatures are highest at 225 deg where a highest hydrodynamic pressure is expected to build up. Measured temperatures at the bearing centerline are higher than those at the side edges, as expected. In addition, large thermal gradients are recorded in the hollow shaft along the axial direction with higher temperatures at the supported end. The axial thermal gradient of the shaft is thought to cause higher temperatures at the bearing right edge facing the ball bearing support than those at the left edge. The paper presents test data along with detailed test GFB/shaft geometries and material properties.