Biomechanical Response of MOD Class II Restorations Considering Polymerization Shrinkage and Transient Occlusal Loading: A Finite Element Study
Authors:
- Alex Benites-AliagaABAlex Benites-Aliaga
- Marcos Robles-LoraMRMarcos Robles-Lora
- Aldo Castillo-ChungACAldo Castillo-Chung
- Elmer Tello-De la CruzECElmer Tello-De la Cruz
- Claudia Torres-RuizCTClaudia Torres-Ruiz
- Anderson Soplin-InfantesASAnderson Soplin-Infantes
- Alexander Vega-AnticonaAVAlexander Vega-Anticona
Open Access
- 29 October 2026
- journal article
- research article
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10713
Abstract
Class II mesio-occluso-distal (MOD) restorations are routinely used to rehabilitate molars with extensive structural loss, where cavity bases are often employed to protect dentin and modulate stress transfer. However, polymer-based restorative materials undergo polymerization shrinkage during curing, generating residual stresses that are subsequently superimposed on functional occlusal loads during mastication. The interaction between these two stress fields is rarely considered explicitly in finite element studies of MOD restorations. This study evaluates the biomechanical influence of cavity base type and the absence of a cavity base in Class II MOD restorations by means of three-dimensional finite element analysis (3D-FEA). A three-dimensional human molar model was reconstructed from cone-beam computed tomography (CBCT) data. A transient occlusal loading cycle from 0 to 0.25 s was simulated, with a maximum load of 600 N applied at 0.15 s. Restorations with cavity bases were modeled using combinations of ceramic and glass–ceramic restorative materials with different base materials, whereas restorations without cavity bases were modeled using reinforced composite resins with different silica contents. Mechanical behavior was assessed through von Mises stress and maximum principal stress. The results show that stress distribution and stress magnitude depend on the interaction among restorative material properties, cavity base configuration, and the overall stiffness of the system. In particular, certain reinforced composite configurations without cavity bases exhibited a more homogeneous stress distribution and a narrower stress range than some multilayer configurations. However, this behavior should not be generalized to all cavity-base-free restorations, as it depends on the specific mechanical properties of the evaluated materials and the structural configuration of the restorative system. These findings highlight the importance of jointly considering polymerization shrinkage and transient occlusal loading in the biomechanical assessment of MOD restorations, and suggest that, under specific conditions, optimization of restorative material properties may be as relevant as the incorporation of intermediate layers.Keywords
All Related Versions
Funding Information
- Vice-Rectorate for Research of César Vallejo University, Trujillo campus (P-2025-205-VI-UCV)
This publication has 31 references indexed in Scilit:
- Stress distribution in zirconia-reinforced glass ionomer restorations in molar incisor hypomineralization: A finite element analysisDental Materials, 2025
- Optimising dental restorative composites: Numerical and statistical analysis of polymerization shrinkage and elastic modulus effectsJournal of the Mechanical Behavior of Biomedical Materials, 2025
- Comparison of the stress distribution in base materials and thicknesses in composite resin restorationsHeliyon, 2024
- Borosilicate glass as a surface finishing alternative for improving the mechanical properties of third-generation zirconiaDental Materials, 2023
- Enhancing the mechanical stability of restored teeth with interfacial cracks: Finite element analysisJournal of the Mechanical Behavior of Biomedical Materials, 2023
- Effect of polymerization mode on shrinkage kinetics and degree of conversion of dual-curing bulk-fill resin compositesClinical Oral Investigations, 2023
- Effect of thickness and CAD‐CAM material on fatigue resistance of endodontically treated molars restored with occlusal veneersJournal of Prosthodontics, 2022
- Polymerization shrinkage and shrinkage stress of bulk-fill and non-bulk-fill resin-based compositesJournal of Dental Sciences, 2021
- The use of different adhesive filling material and mass combinations to restore class II cavities under loading and shrinkage effects: a 3D-FEAComputer Methods in Biomechanics and Biomedical Engineering, 2020
- Resin based restorative dental materials: characteristics and future perspectivesJapanese Dental Science Review, 2019