Relationship between machining accuracy and optical properties of convex blazed grating in ultra-precision cutting
- 17 October 2023
- journal article
- research article
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (22) , 36845-36858
Abstract
For ultra-precision machining of convex blazed grating elements there are inevitable machining errors, surface defects, and surface roughness, all of which can have an impact on their diffraction efficiency. In this paper, we use PCGrate software based on the integration method to establish the machining error model, surface defect model, and surface roughness model of convex spherical blazed grating with a curvature radius of 41.104 mm, a substrate diameter of 14 mm, a grating density of 53.97 line/mm and a blazed angle of 3.86° as the basic specification. To investigate the effect of base curvature radius error, grating period error, blazed angle error, grating ridge and valley passivation radius, Poisson burr height, and blaze surface roughness on their -1 order diffraction efficiency in the 0.95-2.5 µm spectral range. The results show that when the curvature radius error of the spherical base is less than ±80µm, the influence on diffraction efficiency can be ignored. Among the three groups of grating microstructure parameters, the influence of blazed angle on grating diffraction efficiency is the largest, followed by a grating period, and the influence of grating apex angle is the smallest, among which when the error of blazed angle is less than ±0.1° and the error of grating period is less than ±0.1µm, the influence on diffraction efficiency can be ignored. The effect of the passivation radius of the grating valley on the diffraction efficiency is smaller than that of the passivation radius of the grating ridge, and the maximum reduction of diffraction efficiency is 0.096 and 0.144 when the grating ridge and valley passivation radius are 50nm∼650 nm, respectively. The diffraction efficiency decreases significantly in the wavelength range of 1.9-2.5 µm with the increase of Poisson burr height and blaze surface roughness, and its effect on the diffraction efficiency can be neglected when the Poisson burr height is less than 0.5 µm and the blaze surface roughness value is less than RMS 1 nm. The machining error, surface defect, and surface roughness models of the convex blazed grating are optimized to provide a comprehensive machining accuracy basis for ultra-precision cutting of convex grating components.Keywords
Funding Information
- National Key Research and Development Program of China (2019YF0708903)
- National Natural Science Foundation of China (No.51835013, No.51991372, No.52205505, No.52293404, No.52375473)
- National University of Defense Technology (ZK22-12)
- State Key Laboratory of High Performance Complex Manufacturing (No.Kfkt2021-07)
This publication has 25 references indexed in Scilit:
- Tolerance analysis of multilayer diffractive optics based on polychromatic integral diffraction efficiencyApplied Optics, 2015
- Accurate near-field calculation in the rigorous coupled-wave analysis methodJournal of Optics, 2015
- Multi-Ray Channel Modeling and Wideband Characterization for Wireless Communications in the Terahertz BandIEEE Transactions on Wireless Communications, 2014
- Negative and Positive Impact of Roughness and Loss on Subwavelength Imaging for Superlens StructuresPlasmonics, 2013
- Optimization of the Two Parameters of Classical Blaze Grating in Littrow MountAdvanced Materials Research, 2012
- Effects of manufacturing errors on diffraction efficiency for multilayer diffractive optical elementsApplied Optics, 2011
- Diffraction analysis of blazed transmission gratings with a modified extended scalar theoryJournal of the Optical Society of America A, 2008
- Coupling of surface roughness to the performance of computer-generated hologramsApplied Optics, 2007
- Thin element approximation for the analysis of blazed gratings: simplified model and validity limitsOptics Communications, 2004
- Analysis of binary diffraction gratings: Comparison of different approachesJournal of Modern Optics, 1998