HLHuang Li

Huang Li

*This is an algorithmically generated author record based on publicly available information.

Huang Li has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Functional microstructured surface polishing: mechanism and applications

    by Huang Li, Wenwen Lu, Junfeng Liu, Yifan Dai, Xiaoqiang Peng, Hao Hu, Chaoliang Guan, Chao Xu, Tao Lai, Fei Dong


  • Relationship between machining accuracy and optical properties of convex blazed grating in ultra-precision cutting

    by Huang Li, Xiaoqiang Peng, Yueming Wang, Chaoliang Guan, Hao Hu, Chao Xu, Tao Lai, Hao Liu, Junfeng Liu

    For ultra-precision machining of convex blazed grating elements there are inevitable machining errors, surface defects, and surface roughness, all of which can have an impact on their diffraction efficiency. In this paper, we use PCGrate software based on the integration method to establish the machining error model, surface defect model, and surface roughness model of convex spherical blazed grating with a curvature radius of 41.104 mm, a substrate diameter of 14 mm, a grating density of 53.97 line/mm and a blazed angle of 3.86° as the basic specification. To investigate the effect of base curvature radius error, grating period error, blazed angle error, grating ridge and valley passivation radius, Poisson burr height, and blaze surface roughness on their -1 order diffraction efficiency in the 0.95-2.5 µm spectral range. The results show that when the curvature radius error of the spherical base is less than ±80µm, the influence on diffraction efficiency can be ignored. Among the three groups of grating microstructure parameters, the influence of blazed angle on grating diffraction efficiency is the largest, followed by a grating period, and the influence of grating apex angle is the smallest, among which when the error of blazed angle is less than ±0.1° and the error of grating period is less than ±0.1µm, the influence on diffraction efficiency can be ignored. The effect of the passivation radius of the grating valley on the diffraction efficiency is smaller than that of the passivation radius of the grating ridge, and the maximum reduction of diffraction efficiency is 0.096 and 0.144 when the grating ridge and valley passivation radius are 50nm∼650 nm, respectively. The diffraction efficiency decreases significantly in the wavelength range of 1.9-2.5 µm with the increase of Poisson burr height and blaze surface roughness, and its effect on the diffraction efficiency can be neglected when the Poisson burr height is less than 0.5 µm and the blaze surface roughness value is less than RMS 1 nm. The machining error, surface defect, and surface roughness models of the convex blazed grating are optimized to provide a comprehensive machining accuracy basis for ultra-precision cutting of convex grating components.


  • Micro-burrs in machining original molds of an optical functional film with a triangular pyramidal texture

    by Huang Li, Zhilong Xu

    During the cutting process of the original molds, the micro-burrs produced by the machining process will affect the optical properties of the optical functional textured film. According to the forming planing method for the triangular pyramid texture, the formation characteristics of burrs are analyzed from the cut-in edge and the cut-out edge. And the influence of burrs on the triangular pyramid edge is analyzed in combination with the changes of cutting section, to obtain the prediction model of edge burr distribution. The cutting simulation of triangular pyramid texture shows that the main flow direction of the chips will be inclined along the side where the cutting edge is separated from the workpiece first, resulting in a larger exit burr size on this side. In the cut-out stage, as the contact length between the cutting edge of the tool and the workpiece decreases gradually, the maximum cutting stress gradually transfers to the tool tip so that the positive burrs form at the bottom of the cut-out edges of the triangular pyramid. The forming processing experiment for the triangular pyramid texture shows that there are both positive and negative exit burrs on the cut-out edges. Compared with the forming processing method, the V-shaped section of the cutting layer is changed to the trapezoidal section of the free chips when the original molds with triangular pyramid texture are cut by the single-edge cutting method. As the chips flow more smoothly, the size of burrs can be reduced. Besides, the ratio of the effective optical functional area K s can increase 10.1%.