Case Study of a 20 T-$\phi$400 mm Room Temperature Bore Superconducting Outsert for a 45 T Hybrid Magnet
Authors:
- S. AwajiSAS. Awaji
- G. NishijimaGNG. Nishijima
- T. HamajimaTHT. Hamajima
- T. KiyoshiTKT. Kiyoshi
- H. KumakuraHKH. Kumakura
- S. HanaiSHS. Hanai
- M. OnoMOM. Ono
- 6 June 2008
- journal article
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 18 (2) , 552-555
Abstract
The High Field Laboratory for Superconducting Materials (HFLSM) and the Tsukuba Magnet Laboratory (TML) conducted in collaboration a case study on development of a 50 T-class hybrid magnet. To construct a high magnetic field magnet with compact and energy-saving design as well as with easy operation and maintenance, one has to develop high-strength NbSn strand cables, with maximized superconducting characteristics and which can withstand a large electromagnetic force over 500 MPa. For this purpose, the HFLSM has proposed and investigated the effect of repeated bending treatment (pre bending) on NbSn strands internally reinforced with CuNb stabilizer leading to significant enhancement of the critical current density. In this report we present our results on application of the pre bending effect to the development of high-strength strand cables. The designed prebent-strand cables are composed of three CuNb/Nb3Sn strands (3 times Phi =1.73 mm) and four stainless steel strands ( 4 times Phi =1.73 mm). High-strength CuNb/Nb3Sn strand cables have shown a stress limit of 552 MPa at 0.4% strain, and a critical current of Ic =1000 A at 18.5 T and 2.0 K. For such high-strength strand cables, a 20 T superconducting magnet with a room temperature bore (Phi =400 mm) consisting of five layers made of CuNb/NbSn and two layers of NbTi was designed. The coil parameters are: inner diameter Phi = 440 mm, outer diameter Phi = 1332 mm, coil height 1321 mm, inductance 350 H and magnetic stored energy 144 MJ at 908 A of the operation current. Winding of the coil was experimentally successfully simulated using dummy 3 + 4 strands cable composed of three Cu strands and 4 stainless steel strands with a similar design to the 3 + 4 strands superconducting cable presented above. The 20 T superconducting coil will be used as a 20 T outsert for a 25 T water-cooled resistive insert to obtain a 45 T hybrid magnet.Keywords
This publication has 7 references indexed in Scilit:
- Room and low temperature direct three-dimensional-strain measurements by neutron diffraction on as-reacted and prebent CuNb∕Nb3Sn wireJournal of Applied Physics, 2007
- Cryocooled superconducting magnets for high magnetic fields at the HFLSM and future collaboration with the TMLJournal of Physics: Conference Series, 2006
- Large$rm T_rm c$,$rm B_rm c2$and$rm I_rm c$Enhancement Effect Due to the Prebending Treatment for Bronze Route$rm Nb_3rm Sn$WiresIEEE Transactions on Applied Superconductivity, 2005
- The 45T hybrid insert: recent achievementsPhysica B: Condensed Matter, 2001
- The new 20MW high magnetic field installation at the University of NijmegenPhysica B: Condensed Matter, 2001
- The 20 MW-50 mm bore diameter magnet of the Grenoble High Magnetic Field LaboratoryIEEE Transactions on Applied Superconductivity, 2000
- Advanced (Nb,Ti)3Sn Superconducting Wire with Highly Strengthened and Good Conductive CuNb Composite StabilizerMaterials Science Forum, 1999