Effect of mechanical post-treatment on residual stress gradients intextured wear-resistant α-Al2O3 coatings
Authors:
- Siamak ShojaSSSiamak Shoja
- Olof BäckeOBOlof Bäcke
- Anton DavydokADAnton Davydok
- Mikael KritikosMKMikael Kritikos
- Mats HalvarssonMHMats Halvarsson
- Susanne NorgrenSNSusanne Norgren
- Magnus Hörnqvist CollianderMCMagnus Hörnqvist Colliander
Preprint
- 17 August 2026
- preprint
- Published by Elsevier in SSRN Electronic Journal
Abstract
Wear-resistant Al2O3 coatings deposited by chemical vapour deposition are a key technologyfor improving the lifetime and performance of WC-Co cutting tools during metal machining.Post-deposition processes such as wet blasting are commonly used to introduce compressivestresses, while recent advances in crystallographic texture control have enabled further improvements in coating performance. However, the combined influence of texture and blasting on residual stress development remains poorly understood.Here, synchrotron nano-diffraction is used to resolve through-thickness residual stress anddefect gradients in textured α-Al2O3 coatings with (001), (012), and (110) textures beforeand after wet blasting. In the as-deposited state, all coatings exhibit similar weak tensilestresses. Blasting induces compressive stresses (≈ -1 to -2 GPa) with a strong dependenceon texture.The (001) coating develops a pronounced surface-localized stress gradient reaching ≈-4 GPa, whereas the (110) coating exhibits lower and nearly uniform compressive stressesthroughout the coating thickness. The (012) coating shows intermediate behaviour, withdeeper deformation and partial stress relaxation near the surface. Residual stress gradientscorrelate closely with diffraction peak broadening, indicating a strong link to deformation-induced defects.The observed texture dependence is attributed to differences in the activation of basaland prismatic slip systems, which govern the distribution of deformation and defect generation during particle impact. Elastic anisotropy and strong fiber texture further influencethe magnitude of retained compressive stresses, while grain-size effects may provide an additional contribution to stress retention. The results demonstrate that crystallographic texture governs both the magnitude and spatial distribution of blasting-induced residual stresses, providing new insight for texture-controlled stress-gradient engineering in high performance ceramic coatings.Keywords
This publication has 19 references indexed in Scilit:
- Influence of α-Al2O3 texture on residual stress, cooling cracks and hardness in CVD α-Al2O3/Ti(C,N) coatings on cemented carbideSurface and Coatings Technology, 2026
- Enhanced steel machining performance using texture-controlled CVD alpha-alumina coatings: Fundamental degradation mechanismsInternational Journal of Machine Tools and Manufacture, 2024
- On the influence of varying the crystallographic texture of alumina CVD coatings on cutting performance in steel turningInternational Journal of Machine Tools and Manufacture, 2022
- Calculated and experimental Schmid factors for chip flow deformation of textured CVD α-alumina coatingsSurface and Coatings Technology, 2021
- Microstructure investigation of textured CVD alumina coatingsInternational Journal of Refractory Metals and Hard Materials, 2020
- Thermal crack network on CVD TiCN/α-Al2O3 coated cemented carbide cutting toolsInternational Journal of Refractory Metals and Hard Materials, 2019
- Residual stress gradients in α-Al2O3 hard coatings determined by pencil-beam X-ray nanodiffraction: The influence of blasting mediaSurface and Coatings Technology, 2015
- Scratch-induced deformation in fine- and ultrafine-grained bulk aluminaScripta Materialia, 2010
- Enhanced performance of α-Al2O3 coatings by control of crystal orientationSurface and Coatings Technology, 2008
- Deposition, microstructure and properties of texture-controlled CVD α-Al2O3 coatingsInternational Journal of Refractory Metals and Hard Materials, 2005