Anton Davydok
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Anton Davydok has a total of 148 co-authors. Here are the top co-authors by number of shared publications:
Christina Krywka
Institute of Materials Physics Helmholtz‐Zentrum Hereon Outstation at DESY Hamburg Germany
3 shared publications- Helmut Riedl
Christian Doppler Laboratory for Surface Engineering of high-performance Components, TU Wien, Vienna, Austria
2 shared publications Mats Halvarsson
2 shared publicationsP. Polcik
2 shared publicationsPeter Hedström
2 shared publications- Rainer Hahn
Christian Doppler Laboratory for Surface Engineering of high-performance Components, TU Wien, Wien, Austria
2 shared publications
Latest Publications
- Open Access
Visualizing and Quantifying Indentation‐Induced Densification and Cracking in Vitreous Silica
The practical strength of oxide glasses is greatly reduced by surface flaws that form during processing and use. Instrumented indentation can mimic such real‐life damage events and allows for systematic examination of the deformation and structural changes in the regions of the glass being indented. However, structural probing is nearly always performed after rather than during the sharp contact event, limiting our understanding of the indentation process. To overcome this, here we develop and apply an in situ nanofocus X‑ray scattering method for visualizing and quantifying indentation‐induced densification and cracking in glass materials. We demonstrate its feasibility in a proof‐of‐concept experiment by probing the local mechanical and structural response of vitreous silica during indentation. Two‐dimensional mapping of the scattering pattern in the zone below a sharp diamond wedge indenter reveals local changes in the atomic structure and density as well as cracking behavior. These in situ measurements during indentation reveal the formation and evolution of the densification zone and cracking, probing features down to the nanoscale. Although the developed experimental approach can be further improved (especially beam‐sample‐indenter alignment), we believe it will allow for a deeper understanding of the interplay between structural densification and cracking behavior in glasses.
Open AccessVisualizing and Quantifying Indentation‐Induced Densification and Cracking in Vitreous Silica
The practical strength of oxide glasses is greatly reduced by surface flaws that form during processing and use. Instrumented indentation can mimic such real‐life damage events and allows for systematic examination of the deformation and structural changes in the regions of the glass being indented. However, structural probing is nearly always performed after rather than during the sharp contact event, limiting our understanding of the indentation process. To overcome this, here we develop and apply an in situ nanofocus X‑ray scattering method for visualizing and quantifying indentation‐induced densification and cracking in glass materials. We demonstrate its feasibility in a proof‐of‐concept experiment by probing the local mechanical and structural response of vitreous silica during indentation. Two‐dimensional mapping of the scattering pattern in the zone below a sharp diamond wedge indenter reveals local changes in the atomic structure and density as well as cracking behavior. These in situ measurements during indentation reveal the formation and evolution of the densification zone and cracking, probing features down to the nanoscale. Although the developed experimental approach can be further improved (especially beam‐sample‐indenter alignment), we believe it will allow for a deeper understanding of the interplay between structural densification and cracking behavior in glasses.
- Open Access
- 17 August 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of mechanical post-treatment on residual stress gradients intextured wear-resistant α-Al2O3 coatings
Wear-resistant Al2O3 coatings deposited by chemical vapour deposition are a key technologyfor improving the lifetime and performance of WC-Co cutting tools during metal machining.Post-deposition processes such as wet blasting are commonly used to introduce compressivestresses, while recent advances in crystallographic texture control have enabled further improvements in coating performance. However, the combined influence of texture and blasting on residual stress development remains poorly understood.Here, synchrotron nano-diffraction is used to resolve through-thickness residual stress anddefect gradients in textured α-Al2O3 coatings with (001), (012), and (110) textures beforeand after wet blasting. In the as-deposited state, all coatings exhibit similar weak tensilestresses. Blasting induces compressive stresses (≈ -1 to -2 GPa) with a strong dependenceon texture.The (001) coating develops a pronounced surface-localized stress gradient reaching ≈-4 GPa, whereas the (110) coating exhibits lower and nearly uniform compressive stressesthroughout the coating thickness. The (012) coating shows intermediate behaviour, withdeeper deformation and partial stress relaxation near the surface. Residual stress gradientscorrelate closely with diffraction peak broadening, indicating a strong link to deformation-induced defects.The observed texture dependence is attributed to differences in the activation of basaland prismatic slip systems, which govern the distribution of deformation and defect generation during particle impact. Elastic anisotropy and strong fiber texture further influencethe magnitude of retained compressive stresses, while grain-size effects may provide an additional contribution to stress retention. The results demonstrate that crystallographic texture governs both the magnitude and spatial distribution of blasting-induced residual stresses, providing new insight for texture-controlled stress-gradient engineering in high performance ceramic coatings.
- 17 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of mechanical post-treatment on residual stress gradients intextured wear-resistant α-Al2O3 coatings
Wear-resistant Al2O3 coatings deposited by chemical vapour deposition are a key technologyfor improving the lifetime and performance of WC-Co cutting tools during metal machining.Post-deposition processes such as wet blasting are commonly used to introduce compressivestresses, while recent advances in crystallographic texture control have enabled further improvements in coating performance. However, the combined influence of texture and blasting on residual stress development remains poorly understood.Here, synchrotron nano-diffraction is used to resolve through-thickness residual stress anddefect gradients in textured α-Al2O3 coatings with (001), (012), and (110) textures beforeand after wet blasting. In the as-deposited state, all coatings exhibit similar weak tensilestresses. Blasting induces compressive stresses (≈ -1 to -2 GPa) with a strong dependenceon texture.The (001) coating develops a pronounced surface-localized stress gradient reaching ≈-4 GPa, whereas the (110) coating exhibits lower and nearly uniform compressive stressesthroughout the coating thickness. The (012) coating shows intermediate behaviour, withdeeper deformation and partial stress relaxation near the surface. Residual stress gradientscorrelate closely with diffraction peak broadening, indicating a strong link to deformation-induced defects.The observed texture dependence is attributed to differences in the activation of basaland prismatic slip systems, which govern the distribution of deformation and defect generation during particle impact. Elastic anisotropy and strong fiber texture further influencethe magnitude of retained compressive stresses, while grain-size effects may provide an additional contribution to stress retention. The results demonstrate that crystallographic texture governs both the magnitude and spatial distribution of blasting-induced residual stresses, providing new insight for texture-controlled stress-gradient engineering in high performance ceramic coatings.
- Open Access
- 6 May 2026
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 33 (4) , 953-960
Integrated control of a nanoindenter and X-ray nanodiffraction for automated in situ nanomechanical studies
X-ray diffraction (XRD) combined with in situ mechanical testing is a powerful, non-destructive technique that provides valuable information on structural evolution and defect formation during deformation. Unlike many other characterization methods, XRD does not impose constraints on sample dimensions, does not require a vacuum environment, and can be applied to a wide range of materials with periodic structures. However, such experiments present significant challenges due to the need for precise synchronization between independently controlled systems: one managing mechanical loading and the other handling X-ray measurements. In this work, we report on the successful software-level integration of a nanoindenter control system directly into the beamline control system. This integration enables full control of both mechanical and diffraction measurements from a single user interface, allowing real-time synchronization and automation of complex in situ experiments. We demonstrate the capabilities of this setup through uniaxial compression tests on α-Ti micropillars. Mechanical data from the nanoindenter and XRD patterns were collected simultaneously in an automated mode. Raster scans were performed on the micropillar in its pristine state, at two intermediate deformation stages, and post-mortem. This approach enabled detailed analysis of mechanical behavior and structural evolution under load, illustrating the effectiveness of the integrated system for advanced in situ studies.
- 6 May 2026
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 33 (4) , 953-960
Open AccessIntegrated control of a nanoindenter and X-ray nanodiffraction for automated in situ nanomechanical studies
X-ray diffraction (XRD) combined with in situ mechanical testing is a powerful, non-destructive technique that provides valuable information on structural evolution and defect formation during deformation. Unlike many other characterization methods, XRD does not impose constraints on sample dimensions, does not require a vacuum environment, and can be applied to a wide range of materials with periodic structures. However, such experiments present significant challenges due to the need for precise synchronization between independently controlled systems: one managing mechanical loading and the other handling X-ray measurements. In this work, we report on the successful software-level integration of a nanoindenter control system directly into the beamline control system. This integration enables full control of both mechanical and diffraction measurements from a single user interface, allowing real-time synchronization and automation of complex in situ experiments. We demonstrate the capabilities of this setup through uniaxial compression tests on α-Ti micropillars. Mechanical data from the nanoindenter and XRD patterns were collected simultaneously in an automated mode. Raster scans were performed on the micropillar in its pristine state, at two intermediate deformation stages, and post-mortem. This approach enabled detailed analysis of mechanical behavior and structural evolution under load, illustrating the effectiveness of the integrated system for advanced in situ studies.
- Open Access
- 17 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Anisotropic hardness in TiB2±z thin films via depth-resolved crystallographic texture engineering
- 17 November 2025
- Published by Elsevier in Materials & Design
- Vol. 260
Open AccessAnisotropic hardness in TiB2±z thin films via depth-resolved crystallographic texture engineering
- Open Access
- 8 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-10
Local crystallization inside the polymer electrolyte for lithium metal batteries observed by operando nanofocus WAXS
The development of next-generation lithium-based batteries is accompanied by the intention to suppress the formation of dendritic lithium on the electrode, and is dominated by the picture that dendrites start to grow at the electrodes. Shifting from liquid to solid-state electrolytes, a high transference number is a quantity that promises the restraint of such parasitic side reactions. In this study, nanofocus X-ray wide-angle scattering is used to detect possible lithium-based crystallites in the polymer-based electrolyte. We perform operando scanning nanofocus wide-angle X-ray scattering on a composite gel-type polymer consisting of poly(vinylidene fluoride-co-hexafluoropropylene) and the single-ion conducting polymer poly((trifluoromethane) sulfonimide lithium styrene) in a lithium symmetric cell. We observe the occurrence and kinetics of lithium carbonate crystallites inside the electrolyte over a depth of 16 µm during three half-cycles. Furthermore, we prove the existence of lithium hydroxide crystallites near the lithium electrode and their absence in the bulk. Importantly, we identify the growth of pure metallic lithium inside the electrolyte as a sign of lithium dendrite growth happening inside the polymer-based electrolyte and not at the electrodes. Thus, nanofocus wide-angle X-ray scattering visualizes local structure changes such as dendrite formation inside the polymer-based electrolyte despite an unchanged electrochemical performance.
- 8 October 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-10
Open AccessLocal crystallization inside the polymer electrolyte for lithium metal batteries observed by operando nanofocus WAXS
The development of next-generation lithium-based batteries is accompanied by the intention to suppress the formation of dendritic lithium on the electrode, and is dominated by the picture that dendrites start to grow at the electrodes. Shifting from liquid to solid-state electrolytes, a high transference number is a quantity that promises the restraint of such parasitic side reactions. In this study, nanofocus X-ray wide-angle scattering is used to detect possible lithium-based crystallites in the polymer-based electrolyte. We perform operando scanning nanofocus wide-angle X-ray scattering on a composite gel-type polymer consisting of poly(vinylidene fluoride-co-hexafluoropropylene) and the single-ion conducting polymer poly((trifluoromethane) sulfonimide lithium styrene) in a lithium symmetric cell. We observe the occurrence and kinetics of lithium carbonate crystallites inside the electrolyte over a depth of 16 µm during three half-cycles. Furthermore, we prove the existence of lithium hydroxide crystallites near the lithium electrode and their absence in the bulk. Importantly, we identify the growth of pure metallic lithium inside the electrolyte as a sign of lithium dendrite growth happening inside the polymer-based electrolyte and not at the electrodes. Thus, nanofocus wide-angle X-ray scattering visualizes local structure changes such as dendrite formation inside the polymer-based electrolyte despite an unchanged electrochemical performance.
- Open Access
- 23 July 2025
- Published by Elsevier in Materials & Design
- Vol. 257
Enhancing the high-cycle fatigue strength of Ti-Al-N coated Ti-6Al-4V by residual stress design
- 23 July 2025
- Published by Elsevier in Materials & Design
- Vol. 257
Open AccessEnhancing the high-cycle fatigue strength of Ti-Al-N coated Ti-6Al-4V by residual stress design
- 3 June 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 201, 385-399
Gradients in lacunar morphology and cartilage mineralization reflect the mechanical function of the mouse femoral head epiphysis
- 3 June 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 201, 385-399
Gradients in lacunar morphology and cartilage mineralization reflect the mechanical function of the mouse femoral head epiphysis
- Open Access
- 28 May 2025
- Published by Elsevier in Materials Today Communications
- Vol. 47
Micro-focused X-ray diffraction imaging analysis of Fe nitrides and carbides in the compound layer of nitrocarburized and gas nitrided steel surfaces
- 28 May 2025
- Published by Elsevier in Materials Today Communications
- Vol. 47
Open AccessMicro-focused X-ray diffraction imaging analysis of Fe nitrides and carbides in the compound layer of nitrocarburized and gas nitrided steel surfaces
- Top Cited Papers
- 7 November 2024
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 363
Engineering multiple nano-twinned high entropy alloy electrocatalysts toward efficient water electrolysis
- 7 November 2024
- Published by Elsevier in Applied Catalysis B: Environment and Energy
- Vol. 363
Top Cited PapersEngineering multiple nano-twinned high entropy alloy electrocatalysts toward efficient water electrolysis
- Open Access
- 9 July 2024
- Published by Elsevier in Applied Surface Science
- Vol. 670
Chelating agent stimulated LDH post-treatment of PEO coated AA2024
- 9 July 2024
- Published by Elsevier in Applied Surface Science
- Vol. 670
Open AccessChelating agent stimulated LDH post-treatment of PEO coated AA2024