PHYSICAL MODELING OF WEARING PROCESSES OF THE AIRFOIL SHROUD PLATFORMS OF GAS TURBINE ENGINE
Open Access
- 12 March 2024
- journal article
- research article
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 1,p. 69-75
Abstract
Purpose. Development of a methodology for accelerated studies on the wear resistance of tribocombinations operating under complex dynamic contact loading conditions and varying temperatures. Research methods. A methodology and setup have been devised for conducting accelerated studies on the wear resistance of materials under various loading conditions (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions) similar to operational conditions and temperatures. Additionally, the separate influence of each parameter affecting the system load is considered. The variation in load magnitude and displacement amplitudes of specimens is carried out directly during the tests using a control system with stepper motors controlled by the Arduino Uno computing platform. Results. It is demonstrated that the increase in the multicomponent nature of dynamic loading in tribo-coupling contact leads to an escalation in the intensity of wear of heat-resistant alloys. The variation in wear intensity, depending on the test temperature, exhibits a complex nature. Determining the regularities and developing the conditions for the formation of a wear-resistant surface layer of parts of tribocombinations is possible based on the analysis of the amount of wear and the condition of the surface, taking into account the real type of load (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions). Scientific novelty. The physical modeling of the process of wear of the bandage shelves of the blades of the gas turbine under a complex thermodynamic load is considered. Practical value. The setup and methodology for conducting accelerated tests of friction pair models under conditions approximating real tribocombinations operating conditions with various types of loading on flat details are presented. This allows providing technological recommendations for enhancing the wear resistance of gas turbine engines. Conducting accelerated programmable tests will allow to study the condition of the tri-junctions during a load cycle close to the engine duty cycle in flight mode. Мета роботи. Розробка методології прискорених досліджень зносостійкості трибосполучень, які експлуатуються в умовах складного динамічного контактного навантаження та різних температур. Методи дослідження. Розроблено методику та установку для проведення прискорених досліджень матеріалів на зносостійкість з різними умовами навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках) близьких до експлуатаційних та температурах, а також при роздільному впливі кожного з діючих на систему параметрів навантаження. Зміна величини навантаження та амплітуди переміщення зразків проводиться безпосередньо в ході випробувань за рахунок системи керування кроковими двигунами установки обчислювальною платформою Arduino Uno. Отримані результати. Показано, що збільшення багатокомпонентності динамічного навантаження в контакті трибоспряження призводить до збільшення інтенсивності зношування жароміцних сплавів. Зміна інтенсивності зношування, залежно від температури випробувань, має складний характер. Визначення закономірностей та розробка умов формування зносостійкого поверхневого шару деталей трибосполучень можливе на основі аналізу величини зносу та стану поверхні з урахуванням реального виду навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках). Наукова новизна. Розглянуто фізичне моделювання процесу зношування бандажних полиць лопаток турбіни ГТД за складним термодинамічним навантаженням. Практична цінність. Представлено установку та методологію проведення прискорених випробувань моделей фрикційних пар в умовах, наближених до реальних умов експлуатації трибосполучень з різними видами навантаження плоских деталей, що дозволяє дати технологічні рекомендації щодо підвищення зносостійкості газотурбінних двигунів. Проведення прискорених випробувань, що програмуються, дозволить вивчити стан трибоз’єднань у процесі циклу навантаження, наближеного до циклу роботи двигуна в льотному режимі.Keywords
This publication has 5 references indexed in Scilit:
- Features of engineering the wear-resistant surface of parts with the multicomponent dynamic loadWear, 2022
- Increasing Wear Resistance of Steel by Optimizing Structural State of Surface LayerSteel in Translation, 2021
- Application of the Protective Coating for Blade’s Thermal ProtectionEnergies, 2020
- WEAR RESISTANCE AND TRIBOLOGICAL PROPERTIES OF HIGH ENTROPY COATINGS CrNiTiZrCuEurasian Physical Technical Journal, 2020
- Fretting wear of inconel 625 at high temperature and in high vacuumWear, 1985