Volodymyr Tsyganov
Research Subjects
Research Interests
Volodymyr Tsyganov has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Sergiy Sheyko
Zaporizhzhya National University
4 shared publications - Oleksii Hrechanyі
Department of Metallurgical Equipment Zaporizhzhia National University Zaporizhzhia Ukraine
3 shared publications - Tetyana Vasilchenko
Zaporizhzhia National University
3 shared publications - Anastasiia Hrechana
Zaporizhzhya National University
2 shared publications - Mykhaylo Frolov
National University Zaporizhzhia Polytechnic, Zaporizhzhia
2 shared publications - Olha Lazarieva
National University "Zaporizhzhia Polytechnic
2 shared publications
Latest Publications
- Open Access
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
A UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- 30 June 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (2 (56))
Open AccessA UNIFIED ANALYTICAL MODEL FOR DEFORMATION RESISTANCE OF METAL UNDER THERMOPLASTIC PROCESSING CONDITIONS
A unified analytical framework is developed to describe the deformation resistance of metals under thermoplastic processing conditions. The proposed approach is based on the Hansel-Spittel constitutive equation and establishes a direct relationship between yield stress and the key thermomechanical parameters of deformation, including strain, strain rate, and temperature. An analytical solution of the spatial plasticity problem is obtained using harmonic functions, enabling the determination of stress intensity at any point within the deformation zone. The formulation integrates the Huber-Mises plasticity criterion with frictional and geometric factors, resulting in a closed-form expression that links the local stress strain state to process parameters. The model accounts for non-uniform and multi-stage deformation characteristic of rolling and contact loading processes. Its applicability is demonstrated for thermoplastic loading of surface layers in tribological contacts, where deformation resistance plays a decisive role in wear and fatigue damage accumulation. The developed analytical model provides an efficient tool for predicting energy-force parameters and assessing surface layer behavior under complex thermomechanical loading. The proposed framework can be directly applied in engineering calculations, process optimization, and the design of metal forming and tribological systems.
- 9 November 2025
- Published by Springer Nature
- p. 455-460
The Technology of Structural-Energy Adaptation as a Factor in Increasing Operational Characteristics
- 9 November 2025
- Published by Springer Nature
- p. 455-460
The Technology of Structural-Energy Adaptation as a Factor in Increasing Operational Characteristics
- Open Access
- 30 September 2024
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 21 (3(49)) , 63-70
MODELING THE PLASTIC DEFORMATION STATE OF THE CONTACT SURFACE DURING FRICTION
The mechanics of contact destruction of compounds during friction under conditions of complex thermodynamic loading was researched. The possibility of a mathematical description of complex damage to friction units and wear intensity is shown, taking into account the peculiarities of the surface layer formation during contact. A method for calculating the surface strength and durability of tribo-compounds is presented. This allows us to relate the parameters of the stressed state of a point (friction coefficient, shape factor) with the thermomechanical parameters of the process. By assessing changes in the friction coefficient and shape parameters, it becomes possible to determine the yield stress and establish structural transformations corresponding to a given stress state.
- 30 September 2024
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 21 (3(49)) , 63-70
Open AccessMODELING THE PLASTIC DEFORMATION STATE OF THE CONTACT SURFACE DURING FRICTION
The mechanics of contact destruction of compounds during friction under conditions of complex thermodynamic loading was researched. The possibility of a mathematical description of complex damage to friction units and wear intensity is shown, taking into account the peculiarities of the surface layer formation during contact. A method for calculating the surface strength and durability of tribo-compounds is presented. This allows us to relate the parameters of the stressed state of a point (friction coefficient, shape factor) with the thermomechanical parameters of the process. By assessing changes in the friction coefficient and shape parameters, it becomes possible to determine the yield stress and establish structural transformations corresponding to a given stress state.
- 3 July 2024
- Published by Springer Nature
- p. 200-211
Empirical Data-Based Failure Rate Assessment Methodology for Metal-Cutting Tools
- 3 July 2024
- Published by Springer Nature
- p. 200-211
Empirical Data-Based Failure Rate Assessment Methodology for Metal-Cutting Tools
- Open Access
- 7 May 2024
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 59 (3) , 713-720
FEATURES OF THE FORMATION OF THE NANOSTRUCTURAL STATE OF THE SURFACE LAYER OF STEEL PARTS DURING PROCESSING AND OPERATION
Considered patterns of formation of the nanostructural state of the surface layer of machine parts during friction under conditions of complex dynamic loading. The results of the complex assessment of the state of the surface layer of samples after friction continuous indentation and scanning methods indenter, an analysis of changes in the work function of the electron from the surface of the samples. Shown that during the friction of steel surfaces, an increase in transverse slippage contributes to the formation of a more uniform surface layer. This decreases its strength, wear resistance, and a more uniform surface microgeometry. This is accompanied by a decrease in the magnitude and spread of the electron work function over the surface. The relationship between the nanostructural state of a polished surface and roughness and reflectivity is presented.
- 7 May 2024
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 59 (3) , 713-720
Open AccessFEATURES OF THE FORMATION OF THE NANOSTRUCTURAL STATE OF THE SURFACE LAYER OF STEEL PARTS DURING PROCESSING AND OPERATION
Considered patterns of formation of the nanostructural state of the surface layer of machine parts during friction under conditions of complex dynamic loading. The results of the complex assessment of the state of the surface layer of samples after friction continuous indentation and scanning methods indenter, an analysis of changes in the work function of the electron from the surface of the samples. Shown that during the friction of steel surfaces, an increase in transverse slippage contributes to the formation of a more uniform surface layer. This decreases its strength, wear resistance, and a more uniform surface microgeometry. This is accompanied by a decrease in the magnitude and spread of the electron work function over the surface. The relationship between the nanostructural state of a polished surface and roughness and reflectivity is presented.
- Open Access
- 12 March 2024
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 1,p. 69-75
PHYSICAL MODELING OF WEARING PROCESSES OF THE AIRFOIL SHROUD PLATFORMS OF GAS TURBINE ENGINE
Purpose. Development of a methodology for accelerated studies on the wear resistance of tribocombinations operating under complex dynamic contact loading conditions and varying temperatures. Research methods. A methodology and setup have been devised for conducting accelerated studies on the wear resistance of materials under various loading conditions (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions) similar to operational conditions and temperatures. Additionally, the separate influence of each parameter affecting the system load is considered. The variation in load magnitude and displacement amplitudes of specimens is carried out directly during the tests using a control system with stepper motors controlled by the Arduino Uno computing platform. Results. It is demonstrated that the increase in the multicomponent nature of dynamic loading in tribo-coupling contact leads to an escalation in the intensity of wear of heat-resistant alloys. The variation in wear intensity, depending on the test temperature, exhibits a complex nature. Determining the regularities and developing the conditions for the formation of a wear-resistant surface layer of parts of tribocombinations is possible based on the analysis of the amount of wear and the condition of the surface, taking into account the real type of load (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions). Scientific novelty. The physical modeling of the process of wear of the bandage shelves of the blades of the gas turbine under a complex thermodynamic load is considered. Practical value. The setup and methodology for conducting accelerated tests of friction pair models under conditions approximating real tribocombinations operating conditions with various types of loading on flat details are presented. This allows providing technological recommendations for enhancing the wear resistance of gas turbine engines. Conducting accelerated programmable tests will allow to study the condition of the tri-junctions during a load cycle close to the engine duty cycle in flight mode. Мета роботи. Розробка методології прискорених досліджень зносостійкості трибосполучень, які експлуатуються в умовах складного динамічного контактного навантаження та різних температур. Методи дослідження. Розроблено методику та установку для проведення прискорених досліджень матеріалів на зносостійкість з різними умовами навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках) близьких до експлуатаційних та температурах, а також при роздільному впливі кожного з діючих на систему параметрів навантаження. Зміна величини навантаження та амплітуди переміщення зразків проводиться безпосередньо в ході випробувань за рахунок системи керування кроковими двигунами установки обчислювальною платформою Arduino Uno. Отримані результати. Показано, що збільшення багатокомпонентності динамічного навантаження в контакті трибоспряження призводить до збільшення інтенсивності зношування жароміцних сплавів. Зміна інтенсивності зношування, залежно від температури випробувань, має складний характер. Визначення закономірностей та розробка умов формування зносостійкого поверхневого шару деталей трибосполучень можливе на основі аналізу величини зносу та стану поверхні з урахуванням реального виду навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках). Наукова новизна. Розглянуто фізичне моделювання процесу зношування бандажних полиць лопаток турбіни ГТД за складним термодинамічним навантаженням. Практична цінність. Представлено установку та методологію проведення прискорених випробувань моделей фрикційних пар в умовах, наближених до реальних умов експлуатації трибосполучень з різними видами навантаження плоских деталей, що дозволяє дати технологічні рекомендації щодо підвищення зносостійкості газотурбінних двигунів. Проведення прискорених випробувань, що програмуються, дозволить вивчити стан трибоз’єднань у процесі циклу навантаження, наближеного до циклу роботи двигуна в льотному режимі.
- 12 March 2024
- Published by National University "Zaporizhzhia Polytechnic" in New Materials and Technologies in Metallurgy and Mechanical Engineering
- No. 1,p. 69-75
Open AccessPHYSICAL MODELING OF WEARING PROCESSES OF THE AIRFOIL SHROUD PLATFORMS OF GAS TURBINE ENGINE
Purpose. Development of a methodology for accelerated studies on the wear resistance of tribocombinations operating under complex dynamic contact loading conditions and varying temperatures. Research methods. A methodology and setup have been devised for conducting accelerated studies on the wear resistance of materials under various loading conditions (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions) similar to operational conditions and temperatures. Additionally, the separate influence of each parameter affecting the system load is considered. The variation in load magnitude and displacement amplitudes of specimens is carried out directly during the tests using a control system with stepper motors controlled by the Arduino Uno computing platform. Results. It is demonstrated that the increase in the multicomponent nature of dynamic loading in tribo-coupling contact leads to an escalation in the intensity of wear of heat-resistant alloys. The variation in wear intensity, depending on the test temperature, exhibits a complex nature. Determining the regularities and developing the conditions for the formation of a wear-resistant surface layer of parts of tribocombinations is possible based on the analysis of the amount of wear and the condition of the surface, taking into account the real type of load (unidirectional sliding, impact with sliding, impact with sliding in two mutually perpendicular directions). Scientific novelty. The physical modeling of the process of wear of the bandage shelves of the blades of the gas turbine under a complex thermodynamic load is considered. Practical value. The setup and methodology for conducting accelerated tests of friction pair models under conditions approximating real tribocombinations operating conditions with various types of loading on flat details are presented. This allows providing technological recommendations for enhancing the wear resistance of gas turbine engines. Conducting accelerated programmable tests will allow to study the condition of the tri-junctions during a load cycle close to the engine duty cycle in flight mode. Мета роботи. Розробка методології прискорених досліджень зносостійкості трибосполучень, які експлуатуються в умовах складного динамічного контактного навантаження та різних температур. Методи дослідження. Розроблено методику та установку для проведення прискорених досліджень матеріалів на зносостійкість з різними умовами навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках) близьких до експлуатаційних та температурах, а також при роздільному впливі кожного з діючих на систему параметрів навантаження. Зміна величини навантаження та амплітуди переміщення зразків проводиться безпосередньо в ході випробувань за рахунок системи керування кроковими двигунами установки обчислювальною платформою Arduino Uno. Отримані результати. Показано, що збільшення багатокомпонентності динамічного навантаження в контакті трибоспряження призводить до збільшення інтенсивності зношування жароміцних сплавів. Зміна інтенсивності зношування, залежно від температури випробувань, має складний характер. Визначення закономірностей та розробка умов формування зносостійкого поверхневого шару деталей трибосполучень можливе на основі аналізу величини зносу та стану поверхні з урахуванням реального виду навантаження (односпрямоване ковзання, удар з проковзуванням, удар з проковзуванням у двох взаємно перпендикулярних напрямках). Наукова новизна. Розглянуто фізичне моделювання процесу зношування бандажних полиць лопаток турбіни ГТД за складним термодинамічним навантаженням. Практична цінність. Представлено установку та методологію проведення прискорених випробувань моделей фрикційних пар в умовах, наближених до реальних умов експлуатації трибосполучень з різними видами навантаження плоских деталей, що дозволяє дати технологічні рекомендації щодо підвищення зносостійкості газотурбінних двигунів. Проведення прискорених випробувань, що програмуються, дозволить вивчити стан трибоз’єднань у процесі циклу навантаження, наближеного до циклу роботи двигуна в льотному режимі.
- Open Access
- 31 December 2023
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 20 (4(46)) , 61-66
ACCELERATED TESTING OF MECHANICAL AND CHEMICAL EFFECT OF THE ENVIRONMENT ON WEAR RESISTANCE OF PARTS OF TRIBOCOUPLES UNDER COMPLEX DYNAMIC LOADING
The wear of tribocouplings parts under complex dynamic loading conditions is considered. A methodology for accelerated testing of friction pairs under multi-component dynamic loading is offered. The designs stand for modeling the processes of contact interaction, and studies of the wear resistance of tribocouplings, which operate under complex dynamic loading conditions with various lubricating and cooling media, are presented. The results of the impact assessment of mechanic and chemical transformations in the contact zone of tribological interfaces for wear resistance according to the developed method are presented. The variable effectiveness evaluation of the degradation influence products of macromolecular compounds in the composition of cutting fluid on wear resistance of metals in the contact zone of tribocouplings are analysed. The use of the presented materials allows rationally selecting friction pair materials for given operating conditions, developing new wear-resistant materials and coatings, lubricant composition and cooling mediums.
- 31 December 2023
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 20 (4(46)) , 61-66
Open AccessACCELERATED TESTING OF MECHANICAL AND CHEMICAL EFFECT OF THE ENVIRONMENT ON WEAR RESISTANCE OF PARTS OF TRIBOCOUPLES UNDER COMPLEX DYNAMIC LOADING
The wear of tribocouplings parts under complex dynamic loading conditions is considered. A methodology for accelerated testing of friction pairs under multi-component dynamic loading is offered. The designs stand for modeling the processes of contact interaction, and studies of the wear resistance of tribocouplings, which operate under complex dynamic loading conditions with various lubricating and cooling media, are presented. The results of the impact assessment of mechanic and chemical transformations in the contact zone of tribological interfaces for wear resistance according to the developed method are presented. The variable effectiveness evaluation of the degradation influence products of macromolecular compounds in the composition of cutting fluid on wear resistance of metals in the contact zone of tribocouplings are analysed. The use of the presented materials allows rationally selecting friction pair materials for given operating conditions, developing new wear-resistant materials and coatings, lubricant composition and cooling mediums.
- Open Access
- 20 October 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (5) , 140-152
Tribology Characteristics of Heatproof Alloys at a Dynamic Pin Ladening in the Variable Temperature Field
An analysis of the operating conditions of gas turbine engines, their components, and the destruction causes was carried out. The designer problems of tribo-joints operating under difficult conditions of force and temperature loads are singled out. The study aimed at obtaining the comparable...
- 20 October 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (5) , 140-152
Open AccessTribology Characteristics of Heatproof Alloys at a Dynamic Pin Ladening in the Variable Temperature Field
An analysis of the operating conditions of gas turbine engines, their components, and the destruction causes was carried out. The designer problems of tribo-joints operating under difficult conditions of force and temperature loads are singled out. The study aimed at obtaining the comparable...
- Open Access
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
- 1 January 2023
- Published by MIM Research Group in Research on Engineering Structures and Materials
Open AccessDetermination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels
Determination of the optimal temperature regime of plastic deformation of micro alloyed automobile wheel steels