Long-Lasting Electret Melt-Blown Nonwoven Functional Filters Made of Organic/Inorganixc Macromolecular Micron Materials: Manufacturing Techniques and Property Evaluations
Open Access
Abstract
Melt-blown nonwoven fabrics for filtration are usually manufactured using polypropylene, but after a certain time period the middle layer of the mask may have a reduced effect on adsorbing particles and may not be easily stored. Adding electret materials not only increases storage time, but also shows in this study that the addition of electret can improve filtration efficiency. Therefore, this experiment uses a melt-blown method to prepare a nonwoven layer, and adds MMT, CNT, and TiO2 electret materials to it for experiments. Polypropylene (PP) chip, montmorillonite (MMT) and titanium dioxide (TiO2) powders, and carbon nanotube (CNT) are blended and made into compound masterbatch pellets using a single-screw extruder. The resulting compound pellets thus contain different combinations of PP, MMT, TiO2, and CNT. Next, a hot pressor is used to make the compound chips into a high-poly film, which is then measured with differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The optimal parameters are yielded and employed to form the PP/MMT/TiO2 nonwoven fabrics and PP/MMT/CNT nonwoven fabrics. The basis weight, thickness, diameter, pore size, fiber covering ratio, air permeability, and tensile property of different nonwoven fabrics are evaluated in order to have the optimal group of PP-based melt-blown nonwoven fabrics. According to the results of DSC and FTIR measurements, PP and MMT, CNT, and TiO2 are completely mixed, and the melting temperature (Tm), crystallization temperature (Tc) and endotherm area are changed accordingly. The difference in enthalpy of melting changes the crystallization of PP pellets, which in turn changes the fibers. Moreover, the Fourier transform infrared (FTIR) spectroscopy results substantiate that PP pellets are well blended with CNT and MMT, according to the comparisons of characteristic peaks. Finally, the scanning electron microscopy (SEM) observation suggests that with a spinning die temperature of 240 °C and a spinning die pressure lower than 0.01 MPa, the compound pellets can be successfully formed into melt-blown nonwoven fabrics with a 10-micrometer diameter. The proposed melt-blown nonwoven fabrics can be processed with electret to form long-lasting electret melt-blown nonwoven filters.Keywords
Funding Information
- National Science and Technology Council in Taiwan (109-2221-E-468-001-, CMU108-MF-87)
- China Medical University (109-2221-E-468-001-, CMU108-MF-87)
This publication has 36 references indexed in Scilit:
- Fabrication of nanofiber meltblown membranes and their filtration propertiesJournal of Membrane Science, 2013
- Needleless Melt‐Electrospinning of Polypropylene NanofibresJournal of Nanomaterials, 2012
- Polyester-based powder coatings with montmorillonite nanoparticles applied on carbon steelProgress in Organic Coatings, 2012
- Effect of –COOH Functionalized Carbon Nanotubes on Mechanical, Dynamic Mechanical and Thermal Properties of Polypropylene NanocompositesJournal of Thermoplastic Composite Materials, 2011
- Meltblown fibers: Influence of viscosity and elasticity on diameter distributionJournal of Non-Newtonian Fluid Mechanics, 2010
- Surgical mask filter and fit performanceAmerican Journal of Infection Control, 2008
- FTIR study on the nature of water sorbed in polypropylene (PP)/ethylene alcohol vinyl (EVOH) filmsEuropean Polymer Journal, 2006
- Physical interactions at carbon nanotube-polymer interfacePolymer, 2003
- Preparation and crystallization behaviour of PP/PP-g-MAH/Org-MMT nanocompositeEuropean Polymer Journal, 2003
- Prediction of Pressure Drop in Non-Woven Filter Media Using a Hagen-Poiseuille ModelTribology Transactions, 2000