Yan-Yu Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yan-Yu Lin has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ching-Wen Lou
Asia University
3 shared publications - Jia-Horng Lin
Feng Chia University
3 shared publications - Mei-Chen Lin
China Medical University
3 shared publications - Yueh-Sheng Chen
Graduate Institute of Acupuncture Science, Graduate Institute of Integrated Medicine, School of Chinese Medicine, Department of Biomedical Engineering, China Medical University, Taichung 404, Taiwan
3 shared publications - Yang-Min Sue
Laboratory of Fiber Application and Manufacturing, Advanced Medical Care and Protection Technology Research Center, Department of Fiber and Composite Materials, Feng Chia University, Taichung 407102, Taiwan
1 shared publication - Yi-Huan Ho
Laboratory of Fiber Application and Manufacturing, Advanced Medical Care and Protection Technology Research Center, Department of Fiber and Composite Materials, Feng Chia University, Taichung 407102, Taiwan
1 shared publication
Latest Publications
- Open Access
Long-Lasting Electret Melt-Blown Nonwoven Functional Filters Made of Organic/Inorganixc Macromolecular Micron Materials: Manufacturing Techniques and Property Evaluations
Melt-blown nonwoven fabrics for filtration are usually manufactured using polypropylene, but after a certain time period the middle layer of the mask may have a reduced effect on adsorbing particles and may not be easily stored. Adding electret materials not only increases storage time, but also shows in this study that the addition of electret can improve filtration efficiency. Therefore, this experiment uses a melt-blown method to prepare a nonwoven layer, and adds MMT, CNT, and TiO2 electret materials to it for experiments. Polypropylene (PP) chip, montmorillonite (MMT) and titanium dioxide (TiO2) powders, and carbon nanotube (CNT) are blended and made into compound masterbatch pellets using a single-screw extruder. The resulting compound pellets thus contain different combinations of PP, MMT, TiO2, and CNT. Next, a hot pressor is used to make the compound chips into a high-poly film, which is then measured with differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The optimal parameters are yielded and employed to form the PP/MMT/TiO2 nonwoven fabrics and PP/MMT/CNT nonwoven fabrics. The basis weight, thickness, diameter, pore size, fiber covering ratio, air permeability, and tensile property of different nonwoven fabrics are evaluated in order to have the optimal group of PP-based melt-blown nonwoven fabrics. According to the results of DSC and FTIR measurements, PP and MMT, CNT, and TiO2 are completely mixed, and the melting temperature (Tm), crystallization temperature (Tc) and endotherm area are changed accordingly. The difference in enthalpy of melting changes the crystallization of PP pellets, which in turn changes the fibers. Moreover, the Fourier transform infrared (FTIR) spectroscopy results substantiate that PP pellets are well blended with CNT and MMT, according to the comparisons of characteristic peaks. Finally, the scanning electron microscopy (SEM) observation suggests that with a spinning die temperature of 240 °C and a spinning die pressure lower than 0.01 MPa, the compound pellets can be successfully formed into melt-blown nonwoven fabrics with a 10-micrometer diameter. The proposed melt-blown nonwoven fabrics can be processed with electret to form long-lasting electret melt-blown nonwoven filters.
Open AccessLong-Lasting Electret Melt-Blown Nonwoven Functional Filters Made of Organic/Inorganixc Macromolecular Micron Materials: Manufacturing Techniques and Property Evaluations
Melt-blown nonwoven fabrics for filtration are usually manufactured using polypropylene, but after a certain time period the middle layer of the mask may have a reduced effect on adsorbing particles and may not be easily stored. Adding electret materials not only increases storage time, but also shows in this study that the addition of electret can improve filtration efficiency. Therefore, this experiment uses a melt-blown method to prepare a nonwoven layer, and adds MMT, CNT, and TiO2 electret materials to it for experiments. Polypropylene (PP) chip, montmorillonite (MMT) and titanium dioxide (TiO2) powders, and carbon nanotube (CNT) are blended and made into compound masterbatch pellets using a single-screw extruder. The resulting compound pellets thus contain different combinations of PP, MMT, TiO2, and CNT. Next, a hot pressor is used to make the compound chips into a high-poly film, which is then measured with differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The optimal parameters are yielded and employed to form the PP/MMT/TiO2 nonwoven fabrics and PP/MMT/CNT nonwoven fabrics. The basis weight, thickness, diameter, pore size, fiber covering ratio, air permeability, and tensile property of different nonwoven fabrics are evaluated in order to have the optimal group of PP-based melt-blown nonwoven fabrics. According to the results of DSC and FTIR measurements, PP and MMT, CNT, and TiO2 are completely mixed, and the melting temperature (Tm), crystallization temperature (Tc) and endotherm area are changed accordingly. The difference in enthalpy of melting changes the crystallization of PP pellets, which in turn changes the fibers. Moreover, the Fourier transform infrared (FTIR) spectroscopy results substantiate that PP pellets are well blended with CNT and MMT, according to the comparisons of characteristic peaks. Finally, the scanning electron microscopy (SEM) observation suggests that with a spinning die temperature of 240 °C and a spinning die pressure lower than 0.01 MPa, the compound pellets can be successfully formed into melt-blown nonwoven fabrics with a 10-micrometer diameter. The proposed melt-blown nonwoven fabrics can be processed with electret to form long-lasting electret melt-blown nonwoven filters.
- Open Access
Combing High-Modulus Fibers with a Novel Foaming Structure Applied to Protective Sandwich-Structured Composites: Manufacturing Techniques and Property Evaluations
This study proposes the composites with a sandwich structure that is primarily made by the multi-step foaming process. The staple material is polyurethane (PU) foam that is combined with carbon fibers, followed by a Kevlar woven fabric. The composites are evaluated in terms of puncture resistance, buffer absorption, and electromagnetic wave shielding effectiveness (EMSE). The manufacturing process provides the composites with a stabilized structure efficiently. Serving the interlayer, a Kevlar woven fabric are sealed between a top and a bottom layer consisting of both PU foam and an aluminum film in order, thereby forming five-layered composites. Namely, the upper and lower surfaces of the five-layered sandwiches are aluminum films which is laminated on a purpose for the EMSE reinforcement. The test results indicate that the PU foam composites are well bonded and thus acquire multiple functions from the constituent materials, including buffer absorption, puncture resistance, and EMSE. There is much prospect that the PU foam composites can be used as a protective material in diverse fields owing to a flexible range of functions.
Open AccessCombing High-Modulus Fibers with a Novel Foaming Structure Applied to Protective Sandwich-Structured Composites: Manufacturing Techniques and Property Evaluations
This study proposes the composites with a sandwich structure that is primarily made by the multi-step foaming process. The staple material is polyurethane (PU) foam that is combined with carbon fibers, followed by a Kevlar woven fabric. The composites are evaluated in terms of puncture resistance, buffer absorption, and electromagnetic wave shielding effectiveness (EMSE). The manufacturing process provides the composites with a stabilized structure efficiently. Serving the interlayer, a Kevlar woven fabric are sealed between a top and a bottom layer consisting of both PU foam and an aluminum film in order, thereby forming five-layered composites. Namely, the upper and lower surfaces of the five-layered sandwiches are aluminum films which is laminated on a purpose for the EMSE reinforcement. The test results indicate that the PU foam composites are well bonded and thus acquire multiple functions from the constituent materials, including buffer absorption, puncture resistance, and EMSE. There is much prospect that the PU foam composites can be used as a protective material in diverse fields owing to a flexible range of functions.
- Open Access
Thermoplastic Laminated Composites Applied to Impact Resistant Protective Gear: Structural Design and Development
Laminated composites have been commonly applied to all fields. When made into laminated composites, Kevlar woven fabrics are able to provide the required functions. In this study, two types of TPU are incorporated to improve the intralayer features of Kevlar/TPU laminated composites. Hence, the Kevlar/TPU laminated composites consist of firmly bonded laminates while retaining flexibility of the fabrics. Being the interlayer of the laminated composites, the TPU layer provides adhesion while strengthening the tensile property, dynamic puncture resistance, and buffer strength of Kevlar/TPU laminated composites. The test results indicate that with a blending ratio of two types of TRU being 85/15 wt%, the Kevlar/TPU laminated composites exhibit a tensile strength of 18.08 MPa. When the stacking thickness is 1 mm, the tensile strength is improved to 357.73 N with the buffering strength reaching 4224.40 N. Notably, with a thickness being 1.2 mm, the laminated composites demonstrate a dynamic resistance being 672.15 N. In the meanwhile, functional Kevlar fabrics are allowed to keep the fiber morphology owing to the protection of TPU composite films. Considering the composition of protective gear, Kevlar/TPU laminated composites possess a powerful potential and are worthwhile exploring.
Open AccessThermoplastic Laminated Composites Applied to Impact Resistant Protective Gear: Structural Design and Development
Laminated composites have been commonly applied to all fields. When made into laminated composites, Kevlar woven fabrics are able to provide the required functions. In this study, two types of TPU are incorporated to improve the intralayer features of Kevlar/TPU laminated composites. Hence, the Kevlar/TPU laminated composites consist of firmly bonded laminates while retaining flexibility of the fabrics. Being the interlayer of the laminated composites, the TPU layer provides adhesion while strengthening the tensile property, dynamic puncture resistance, and buffer strength of Kevlar/TPU laminated composites. The test results indicate that with a blending ratio of two types of TRU being 85/15 wt%, the Kevlar/TPU laminated composites exhibit a tensile strength of 18.08 MPa. When the stacking thickness is 1 mm, the tensile strength is improved to 357.73 N with the buffering strength reaching 4224.40 N. Notably, with a thickness being 1.2 mm, the laminated composites demonstrate a dynamic resistance being 672.15 N. In the meanwhile, functional Kevlar fabrics are allowed to keep the fiber morphology owing to the protection of TPU composite films. Considering the composition of protective gear, Kevlar/TPU laminated composites possess a powerful potential and are worthwhile exploring.