Multiple performance evaluation of asphalt binders modified with micronized polyethylene terephthalate (PET), polyphosphoric acid (PPA) and ethylene–methyl acrylate–glycidyl methacrylate (EMA-GMA)
Authors:
- Leonardo Rodrigues GuedesLGLeonardo Rodrigues Guedes
- Lara Pereira Tavares MendesLMLara Pereira Tavares Mendes
- John Kennedy Guedes RodriguesJRJohn Kennedy Guedes Rodrigues
- Jonny Dantas PatricioJPJonny Dantas Patricio
- Paulo Germano Tavares Marinho FilhoPFPaulo Germano Tavares Marinho Filho
- Manoel Leandro AraújoMAManoel Leandro Araújo
- Arthur Felipe de Farias MonteiroAMArthur Felipe de Farias Monteiro
- João Pedro Silveira SalustianoJSJoão Pedro Silveira Salustiano
- Rita Flávia Régis QueirozRQRita Flávia Régis Queiroz
- Ana Maria Gonçalves Duarte MendonçaAMAna Maria Gonçalves Duarte Mendonça
- Arthur Nóbrega de SousaASArthur Nóbrega de Sousa
- Osires de Medeiros Melo NetoOsires de Medeiros Melo Neto
Open Access
- 23 October 2026
- journal article
- research article
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 11 (11) , 647
Abstract
Recycled polyethylene terephthalate (PET) has been investigated as an asphalt modifier, although compatibility, storage stability, and performance optimization remain challenges. This study evaluated a ternary modification strategy combining micronized PET, ethylene–methyl acrylate–glycidyl methacrylate (EMA-GMA), and polyphosphoric acid (PPA) to improve the physical and rheological properties of asphalt binders. A control binder (AB 50/70, PG 64-22) was modified using three formulations: M1 (1.80% EMA-GMA + 0.30% PET + 0.15% PPA), M2 (1.26% EMA-GMA + 0.21% PET + 0.15% PPA), and M3 (0.90% EMA-GMA + 0.15% PET + 0.15% PPA). Physical, chemical, storage-stability, and rheological characterization included penetration, softening point, rotational viscosity, Performance Grade, Multiple Stress Creep Recovery (MSCR), and Linear Amplitude Sweep (LAS) tests. The ternary modification increased the softening point by up to approximately 34% and elastic recovery from 0% for the control to 86% for M1. Viscosity remained below 3 Pa s at 135 °C. M1 reduced Jnr at 3.2 kPa from 4.51 to 0.43 kPa −1 , meeting the binder classification for extremely heavy traffic. LAS indicated intermediate fatigue performance for M1 (BFF = 1.42), whereas the SBS-modified reference binder showed superior performance (BFF = 1.48). M1 also exhibited an Aging Index approximately 22.7% lower than the control after short-term RTFO aging. Overall, M1 provided the most favorable binder-scale balance among rutting resistance, fatigue damage resistance, storage stability, and short-term aging response.Keywords
This publication has 64 references indexed in Scilit:
- Influence of Blending Parameters on Temperature Susceptibility of Rice Husk Ash Modified AsphaltTransportation in Developing Economies, 2025
- Eco-efficient modification of asphalt binders and mixtures using elevated ratios of polyethylene terephthalate and crumb rubber waste: a step towards sustainable roadsInnovative Infrastructure Solutions, 2025
- Performance Evaluation of Using Waste Polyethylene Terephthalate (PET) Derived Additives for Asphalt Binder ModificationWaste and Biomass Valorization, 2024
- Application of solid waste materials in cold bitumen emulsion mixtures for cleaner pavement industry: a comprehensive reviewEnvironmental Science and Pollution Research, 2024
- Effects of using waste high-density polyethylene on the rheological, mechanical, and thermal performance of asphalt materialsEnvironment, Development and Sustainability, 2023
- Physical and Rheological Study of Asphalt Binders with Soybean Oil Sludge and Soybean Oil Sludge Fatty AcidWaste and Biomass Valorization, 2022
- Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modelingMechanics of Time-Dependent Materials, 2016
- Influence of aging on thermal behavior and characterization of SBR compound-modified asphaltJournal of Thermal Analysis and Calorimetry, 2013
- The colloidal structure of bitumen: Consequences on the rheology and on the mechanisms of bitumen modificationAdvances in Colloid and Interface Science, 2009
- Processing, rheology, and storage stability of recycled EVA/LDPE modified bitumenPolymer Engineering & Science, 2007