LMLara Pereira Tavares Mendes

Lara Pereira Tavares Mendes

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lara Pereira Tavares Mendes has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Multiple performance evaluation of asphalt binders modified with micronized polyethylene terephthalate (PET), polyphosphoric acid (PPA) and ethylene–methyl acrylate–glycidyl methacrylate (EMA-GMA)

    by Leonardo Rodrigues Guedes, Lara Pereira Tavares Mendes, John Kennedy Guedes Rodrigues, Jonny Dantas Patricio, Paulo Germano Tavares Marinho Filho, Manoel Leandro Araújo, Arthur Felipe de Farias Monteiro, João Pedro Silveira Salustiano, Rita Flávia Régis Queiroz, Ana Maria Gonçalves Duarte Mendonça, et al.

    Recycled polyethylene terephthalate (PET) has been investigated as an asphalt modifier, although compatibility, storage stability, and performance optimization remain challenges. This study evaluated a ternary modification strategy combining micronized PET, ethylene–methyl acrylate–glycidyl methacrylate (EMA-GMA), and polyphosphoric acid (PPA) to improve the physical and rheological properties of asphalt binders. A control binder (AB 50/70, PG 64-22) was modified using three formulations: M1 (1.80% EMA-GMA + 0.30% PET + 0.15% PPA), M2 (1.26% EMA-GMA + 0.21% PET + 0.15% PPA), and M3 (0.90% EMA-GMA + 0.15% PET + 0.15% PPA). Physical, chemical, storage-stability, and rheological characterization included penetration, softening point, rotational viscosity, Performance Grade, Multiple Stress Creep Recovery (MSCR), and Linear Amplitude Sweep (LAS) tests. The ternary modification increased the softening point by up to approximately 34% and elastic recovery from 0% for the control to 86% for M1. Viscosity remained below 3 Pa s at 135 °C. M1 reduced Jnr at 3.2 kPa from 4.51 to 0.43 kPa −1 , meeting the binder classification for extremely heavy traffic. LAS indicated intermediate fatigue performance for M1 (BFF = 1.42), whereas the SBS-modified reference binder showed superior performance (BFF = 1.48). M1 also exhibited an Aging Index approximately 22.7% lower than the control after short-term RTFO aging. Overall, M1 provided the most favorable binder-scale balance among rutting resistance, fatigue damage resistance, storage stability, and short-term aging response.

  • Measuring Circularity in Asphalt Mixtures: A Scoping Review of Methods, Gaps, and Challenges

    by Osires de Medeiros Melo Neto, Lara Pereira Tavares Mendes, Ingridy Minervina Silva, Leda Christiane de Figueiredo Lopes Lucena, Luciana de Figueiredo Lopes Lucena, Ali Alnaqbi, Ahmed M. Youssef, Rouba Joumblat

  • Improving mechanical strength and leachability behavior of bauxite tailings for dry stacking using Portland Cement

    by Gilson Gabriel Teixeira Varela, David Braga Fernandes, Aldenora Vieira Santos Neta, Alisson Do Nascimento Lima, Lara Pereira Tavares Mendes, Manoel Leandro Araújo e Farias, Carina Silvani

    The disposal of tailings has become a challenge for the mining sector, environmental agencies, and society. This research aims to analyze the geomechanical and environmental behavior of cemented bauxite tailings (BT) for use in cemented dry tailings piles, a new trend for tailing disposal. The experimental program consisted of a series of unconfined compression tests and splitting tensile tests in BT with addition of 2%, 4%, and 6% of Portland Cement (Ci), and compacted at 18 kN/m3, 19 kN/m3, and 20 kN/m3. Leachability and solubilization tests were done with specimens with 20 kN/m3 and Ci of 0%, 4%, and 6%. All samples were done with water content of 18% and cured for 7 days. Increasing in Portland cement content and dry units of weight increases unconfined compressive strength (qu) and splitting tensile strength (qt); therefore, the increase in porosity decreases these mechanical properties. The importance of those parameters was confirmed by ANOVA and Tukey test analysis. The porosity/Portland cement content index allowed the prediction of qu and qt of BT-Portland cement blends; however, the qt/qu remained constant (0.14) and independent of this index. The environmental analysis showed that the addition of Portland cement to BT reduced the concentration of manganese in the leachate and the concentrations of chromium, iron, and sodium in the solubilized extract, complying with the toxicity and drinking water standards recommended by the USEPA. However, it also increased the concentration of aluminum in both extracts, exceeding the limit set by CONAMA 460 (Brazilian standard).

  • Open Access

    Mechanical and Circularity Analysis of Asphalt Mixtures Produced with Bauxite Residue and RAP

    by Lara Pereira Tavares Mendes, Osires de Medeiros Melo Neto, Leonardo Rodrigues Guedes, Maria Eloisa Barbosa da Silva, Leda Christiane de Figueiredo Lopes Lucena, Luciana de Figueiredo Lopes Lucena

    Industrialization and urbanization generate significant waste volumes, demanding sustainable solutions in sectors like mining and infrastructure. This study evaluates the technical and environmental feasibility of incorporating 5% bauxite residue (BR) and 20% Reclaimed Asphalt Pavement (RAP) into asphalt mixtures. The research integrated physical characterization, mechanical performance testing, and a circularity assessment using the Material Circularity Index (MCI). Mechanical results showed that the combined use of RAP and BR significantly enhanced stiffness and rutting resistance, increasing the Resilient Modulus by 79.79% and the Flow Number (resistance to permanent deformation) from 301 to 800 cycles compared to the reference mixture. Despite higher stiffness, the recycled mixture maintained a Retained Indirect Tensile Strength (ITSR) of 93%, well above the technical requirement of 70%. Aging, intensified by RAP, reduced moisture susceptibility but increased surface wear vulnerability, while mixtures with RAP and bauxite residue demonstrated fatigue performance equivalent to the reference mixture. Regarding circularity, evaluated through two distinct utility factor methodologies, the mixture with 20% RAP and 5% BR demonstrated superior resource efficiency. It achieved an MCI of 0.93 (Method 1) and 0.91 (Method 2), significantly outperforming the conventional mixture, which presented an MCI of only 0.10. Furthermore, these mixtures exhibited superior circularity, reducing virgin material consumption and mitigating environmental impacts across the pavement life cycle, demonstrating a sustainable, efficient approach.


  • Open Access

    Characterization of marble powder waste and evaluation of its applicability in mortars

    by Manoel Leandro Araújo e Farias, Ana Letícia Feitosa de Macêdo, John Kennedy Guedes Rodrigues, Arthur Nóbrega de Sousa, Ana Maria Gonçalves Duarte, Amanda Mendes Arruda, Lara Pereira Tavares Mendes, Paulo Germano Tavares Marinho Filho, Leonardo Rodrigues Guedes, Thamires Dantas Guerra, et al.

    Natural stone materials used for ornamental and cladding purposes, defined by the Brazilian standard ABNT as naturally occurring rock substances processed for aesthetic applications, play a significant role in civil construction by contributing to both the durability and visual appeal of buildings. However, the processing of these stones produces waste that can lead to considerable environmental impacts. This study explores the potential reuse of waste generated during the cutting of marble slabs as a component in mortar formulations. Physical, chemical, and mineralogical characterizations of the waste were carried out, along with mechanical and physical testing of mortar specimens. The findings reveal that mortar incorporating 20% of marble residue as a fine aggregate replacement exhibited improved compressive strength compared to the control mix. Chemically, the residue resembles conventional raw materials, and its mineralogical profile is dominated by calcite and dolomite—common constituents of carbonate rocks. These results support the technical feasibility of incorporating marble cutting waste into masonry mortar, offering a sustainable strategy for waste valorization in the ornamental stone industry.

  • Open Access

    Use of waste tire rubber as a fine aggregate substitute in concrete

    by Manoel Leandro Araújo e Farias, Ana Letícia Feitosa de Macêdo, John Kennedy Guedes Rodrigues, Arthur Nóbrega de Sousa, Ana Maria Gonçalves Duarte, Amanda Mendes Arruda, Lara Pereira Tavares Mendes, Paulo Germano Tavares Marinho Filho, Leonardo Rodrigues Guedes, Thamires Dantas Guerra, et al.

    The civil construction sector significantly contributes to economic growth but also heavily exploits natural resources, raising sustainability concerns. This study investigates the incorporation of waste tire rubber as a partial substitute for fine aggregate in plain concrete to promote environmentally friendly construction practices. Concrete specimens were produced with 10% and 25% rubber content by mass replacing natural fine aggregate. Physical characterization of materials and mechanical testing, including compressive and splitting tensile strength, were conducted at curing ages of 7, 14, and 21 days. Results demonstrated a reduction in compressive and tensile strength proportional to the amount of rubber incorporated. Despite this decrease, the modified concrete meets the requirements for certain non-structural applications, offering advantages such as lower density and enhanced energy absorption. Water absorption increased with higher rubber content, attributed to rubber’s elastic nature and higher absorption capacity. The study confirms the viability of using tire rubber waste in concrete as a sustainable alternative to reduce environmental impact and promote circular economy practices in construction.

  • Open Access

    Mechanical and microstructural assessment of concrete with fine aggregate partially replaced by tire rubber waste

    by Manoel Leandro Araújo e Farias, Ana Letícia Feitosa de Macêdo, John Kennedy Guedes Rodrigues, Arthur Nóbrega de Sousa, Ana Maria Gonçalves Duarte, Amanda Mendes Arruda, Lara Pereira Tavares Mendes, Paulo Germano Tavares Marinho Filho, Leonardo Rodrigues Guedes, Thamires Dantas Guerra, et al.

    The construction industry is one of the sectors that most intensively exploits natural resources during production; however, it is also one of the largest sectors in terms of waste reuse, offering high potential for sustainability. Concrete, as the most widely consumed material in the world, is responsible for providing stability, strength, and workability to structures. The study of incorporating waste materials into concrete is of great importance, as it enables reuse and reduces environmental impact. Among the most environmentally harmful industrial wastes is rubber derived from end-of-life tires. This study aimed to evaluate the performance of concrete incorporating tire rubber waste. Cylindrical specimens (10 cm × 20 cm) were molded with partial replacement of fine aggregate by 10% and 20% of rubber from end-of-life tires. Physical characterization tests were performed on the rubber waste, conventional aggregates, and cement, as well as physical and mechanical characterization of the concrete containing rubber waste, through axial compressive strength and splitting tensile strength tests. Although the incorporation of rubber waste led to a reduction in mechanical properties with increasing content, the results showed that for an adequate level of replacement, the use of rubberized concrete is feasible for various applications. Additionally, the inclusion of rubber waste imparted desirable properties to the concrete, such as energy absorption capacity and improved flexibility, thereby enhancing the overall performance of the mixture.

  • Open Access

    Mechanical behavior evaluation of asphalt mixtures using alternative fillers: a literature review and comparative analysis

    by Manoel Leandro Araújo e Farias, Ana Letícia Feitosa de Macêdo, John Kennedy Guedes Rodrigues, Arthur Nóbrega de Sousa, Ana Maria Gonçalves Duarte, Amanda Mendes Arruda, Lara Pereira Tavares Mendes, Paulo Germano Tavares Marinho Filho, Leonardo Rodrigues Guedes, Thamires Dantas Guerra, et al.

    This study evaluates the mechanical performance of asphalt mixtures incorporating alternative fillers derived from industrial by-products and waste materials, aiming to promote sustainable pavement engineering. The asphalt layer in flexible pavements is critical for load distribution, water sealing, and surface durability. While traditional fillers like hydrated lime and Portland cement improve mixture properties, environmental concerns drive the search for sustainable alternatives. Through a comprehensive literature review, materials such as hydrated lime, bauxite residue (red mud), rice husk ash, fly ash, steel slag glass powder, and recycled concrete aggregate powder were analyzed based on mechanical tests including Tensile Strength by Diametral Compression (RT), Resilience Modulus (Mr), Modified Lottman, and fatigue testing. Findings reveal that all alternative fillers comply with DNIT-EM 367 (1997) standards and generally exhibit satisfactory or enhanced mechanical behavior compared to conventional fillers. Notably, bauxite residue significantly reduced permanent deformation, while rice husk ash and kaolin processing residues improved moisture resistance. Iron oxide increased stiffness but posed challenges related to mixture flexibility and stress response. The results underscore the potential of these industrial residues as cost-effective, environmentally friendly fillers that contribute to improved pavement performance while reducing reliance on natural resources and minimizing waste disposal impacts. Despite promising laboratory outcomes, further research is needed to establish standardized testing protocols and evaluate long-term field performance to fully validate the practical applicability of these alternative fillers in asphalt mixtures. This approach aligns with sustainable infrastructure development by integrating waste valorization into pavement materials technology.

  • Asphalt mixtures with bauxite residue as a partial replacement for fine aggregates: technical, economic, and environmental assessment

    by Lara Pereira Tavares Mendes, Osires de Medeiros Melo Neto, Leonardo Rodrigues Guedes, Gilson Gabriel Teixeira Varela, Aldenora Vieira Santos Neta, David Braga Fernandes, Leda Christiane de Figueiredo Lopes Lucena, Luciana de Figueiredo Lopes Lucena

    The generation of waste is inherent to production systems, necessitating proper management to mitigate environmental and economic impacts. In the mining sector, bauxite residue (BR), a byproduct from alumina production, presents significant environmental challenges due to its contaminant potential but also offers opportunities for reuse. This study evaluates the incorporation of BR in asphalt mixtures as a partial replacement for fine aggregates, assessing mechanical performance, environmental aspects, and economic impact. The methodology involved three stages: (i) physical, chemical, and environmental characterization of BR and aggregates; (ii) production of asphalt mixtures with 5%, 10%, and 15% BR, and mechanical characterization before and after long-term thermal aging (LTOA), including indirect tensile strength (ITS), moisture-induced damage, resilient modulus (RM), dynamic modulus (DM), fatigue life, and permanent deformation resistance; and (iii) economic and environmental evaluation, including leaching tests to assess the mobility of soluble metals and cost analysis for storage and disposal by the mining company. Results indicated that BR incorporation increased fine content, improving stiffness and performance in ITS, RM, DM, and permanent deformation resistance, both before and after LTOA. However, soluble metals in BR led to higher moisture susceptibility, requiring mitigation strategies. From an environmental perspective, BR reduced soluble metal mobility, indicating potential for residue encapsulation. Economically, partial BR substitution reduced storage and disposal costs for the mining company. These findings suggest that using bauxite residue in asphalt mixtures can be a sustainable, economically viable solution for the mining industry.


  • Economic and environmental benefits of recycled asphalt mixtures: impact of reclaimed asphalt pavement and additives throughout the life cycle

    by Laiana Ferreira da Costa, Lara Pereira Tavares Mendes, Osires de Medeiros Melo Neto, Leda Christiane de Figueiredo Lopes Lucena, Luciana de Figueiredo Lopes Lucena

    This study investigates the economic and environmental advantages of using recycled asphalt mixtures with varying percentages of Reclaimed Asphalt Pavement (RAP), cottonseed oil, and zeolite. The primary objective was to assess these mixtures’ life cycle impacts and costs compared to a traditional control mixture. The methodology employed includes Life Cycle Assessment (LCA) and Life Cycle Cost Assessment (LCCA), with a focus on endpoint impact categories such as ecosystem damage, human health, and resource availability. The analysis encompassed production, construction, and end-of-life phases, utilizing an 8.5% discount rate and a 10-year planning horizon. Results indicate that recycled asphalt mixtures with RAP and additives show significant environmental benefits, including reductions in impacts across all evaluated categories. Specifically, RAP incorporation led to substantial reductions in resource consumption and lower life cycle costs. Mixtures with 33% RAP and 10% cottonseed oil, and 33% RAP and 0.3% zeolite, demonstrated the highest cost savings and environmental performance improvements. The findings highlight that while the inclusion of additives increases some costs, the overall economic advantage of RAP utilization is substantial. This research underscores the feasibility of using recycled asphalt mixtures as a sustainable alternative to traditional mixtures, offering both economic and environmental benefits. Graphical abstract