Bio-Inspired Graphitic Carbon-Based Large-Area (10 × 10 cm2) Perovskite Solar Cells: Stability Assessments under Indoor, Outdoor, and Water-Soaked Conditions
- 13 September 2022
- journal article
- research article
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 14 (38) , 43050-43066
Abstract
In the emerging photovoltaic (PV) technologies, the golden triangle rule includes higher efficiency, longevity (or stability), and low cost, which are the foremost criteria for the root of commercial feasibility. Accordingly, a unique low-cost, ecofriendly, all-solution-processed, "bio-inspired" graphitic carbon (extracted from the most invasive plant species of Eichhornia crassipes: listed as one of the 100 most dangerous species by the International Union for Conservation of Nature) and a mixed halide perovskite interface-engineered, unique single-cell large-scale (10 × 10 sq.cm with an active area of 88 cm2) carbon-based perovskite solar cell (C-PSC) are demonstrated for the first time, delivering a maximum PCE of 6.32%. Notable performance was observed under low light performance for the interface-engineered champion device fabricated using the layer-to-layer approach, which, even when tested under fluorescent room light condition (at 200 lux of about ∼0.1 SUN illumination), exhibited a significant PCE. In terms of addressing the stability issues in the fabricated PSC devices, the present work has adopted a two-step strategy: the instability toward the extrinsic factors is addressed by encapsulation, and the subsequent intrinsic instability issue is also addressed through interfacial engineering. Surprisingly, when tested under various stability conditions (STC) such as ambient air, light (continuous 1 SUN, under room light illumination (0.1 SUN) and direct sunlight), severe damp up to a depth of ∼25 mm water (cold (∼15 °C) and hot (∼65 °C)), acidic pH (∼5), and alkaline pH (∼11)) conditions, the fabricated large-scale carbon-based perovskite solar cells (C-LSPSCs) retained unexpected long-term stability in their performance for over 50 days. As to appraise the performance superiority of the fabricated C-LSPSC devices under various aforesaid testing conditions, a working model of a mini-fan has been practically powered and demonstrated.Keywords
Funding Information
- H?gskulen p? Vestlandet
- Utdannings- og forskningsdepartementet
- Indo-Norwegian Collaborative Project
This publication has 93 references indexed in Scilit:
- Structure Engineering of Hole–Conductor Free Perovskite-Based Solar Cells with Low-Temperature-Processed Commercial Carbon Paste As CathodeACS Applied Materials & Interfaces, 2014
- Efficient hole-conductor-free, fully printable mesoscopic perovskite solar cells with a broad light harvester NH2CHNH2PbI3Journal of Materials Chemistry A, 2014
- Full Printable Processed Mesoscopic CH3NH3PbI3/TiO2 Heterojunction Solar Cells with Carbon Counter ElectrodeScientific Reports, 2013
- Optimization of polymer photovoltaic cells with bulk heterojunction layers hundreds of nanometers thick: modifying the morphology and cathode interfaceEnergy & Environmental Science, 2013
- Raman Spectroscopy of Amorphous Carbon Prepared by Pulsed Arc Discharge in Various Gas MixturesJournal of Spectroscopy, 2012
- Silica-templated melamine–formaldehyde resin derived adsorbents for CO2 captureCarbon, 2008
- Synthesis and Application of Graphitic Carbon with High Surface AreaAdvanced Functional Materials, 2008
- Impact of carbon structure and morphology on the electrochemical performance of LiFePO4/C compositesJournal of Solid State Electrochemistry, 2007
- Open circuit voltage improvement of high-deposition-rate microcrystalline silicon solar cells by hot wire interface layersApplied Physics Letters, 2005
- Interpretation of Raman spectra of disordered and amorphous carbonPhysical Review B, 2000