Patient-specific 3D printing to replace components of a rib-to pelvis “Eiffel Tower” vertebral expanding prosthetic titanium rib system in an infant: a case report
Authors:
- 27 November 2022
- journal article
- case report
- Published by Springer Nature in European Spine Journal
- Vol. 32 (7) , 2607-2614
Abstract
Purpose To address the anatomical challenges facing complex and revision spinal surgery, patient-specific 3D-printed models (3D-PMs) have received growing attention worldwide, primarily in adults. We report the use of a 3D-PM in the treatment of a case of wound breakdown over a component of a VEPTR (Vertical Expandable Prosthetic Titanium Rib; DePuy-Synthes) system, requiring replacement of Dunn-McCarthy hook and sleeve with components contoured to a patient-specific 3D-PM of the spine. Method A two-year-old born with myelomeningocele (MMC), repaired at birth, developed progressive MMC-associated kyphoscoliosis. Elective insertion of a rib-to-pelvis ‘Eiffel Tower’ bilateral VEPTR growing rods construct was performed without initial complication. Prominence of the right VEPTR sleeve and Dunn-McCarthy hook side-to-side connector resulted in breakdown of overlying poor-quality soft tissues, necessitating washout, partial implant removal, intravenous antibiotic therapy and delayed primary wound closure. A patient-specific 3D-PM, utilising pre-operative CT spine and pelvis 3D-reconstructions, allowed pre-operative formation of a contoured implant, which was inserted without need for further revision. Results The patient underwent further VEPTR lengthening without recurrent infection, wound breakdown or implant failure at 24-month follow-up. Satisfactory control of the deformity has been achieved with continued improvement in sitting height and radiographic indices. Conclusion This case illustrates the possibility, in certain cases, of using 3D-PM to develop complex components of spinal implant systems pre-operatively, removing the time and difficulty of intra-operative contouring. Consequently, custom-contoured implants may be produced, sterilised and implanted. This technique may be an option, in infants, including MMC-associated kyphoscoliosis, where midline fixation is not possible.Keywords
This publication has 19 references indexed in Scilit:
- Designing patient-specific solutions using biomodelling and 3D-printing for revision lumbar spine surgeryEuropean Spine Journal, 2018
- Preliminary results of a 3D-printed acetabular component in the management of extensive defectsHIP International, 2017
- The utility of 3D printing for surgical planning and patient-specific implant design for complex spinal pathologies: case reportJournal of Neurosurgery: Spine, 2017
- Complications in using the vertical expandable prosthetic titanium rib (VEPTR) in childrenJournal of Pediatric Surgery, 2016
- Use of Vertical Expandable Prosthetic Titanium Rib (VEPTR) in the Treatment of Congenital Scoliosis Without Fused RibsJournal of Pediatric Orthopaedics, 2016
- Pediatric Patient with Incidental Os Odontoideum Safely Treated with Posterior Fixation Using Rod-Hook System and Preoperative Planning Using 3D Printer: A Case ReportJournal of Neurological Surgery Part A: Central European Neurosurgery, 2016
- Clinical application of three-dimensional printing in the personalized treatment of complex spinal disordersChinese Journal of Traumatology, 2016
- Application of 3D Rapid Prototyping Technology in Posterior Corrective Surgery for Lenke 1 Adolescent Idiopathic Scoliosis PatientsMedicine, 2015
- Wound Complications of Vertical Expandable Prosthetic Titanium Rib IncisionsSpine, 2014
- Acellular Dermal Matrix in the Treatment and Prevention of Exposed Vertical Expandable Prosthetic Titanium RibsSpine, 2011