ANALYSIS OF REGULATORY REQUIREMENTS AND PHASE EQUILIBRIUM DIAGRAMS OF BRONZES OF THE Cu‒Sn‒Si SYSTEM
Authors:
- К. І. УзловКУК. І. Узлов
- Л. І. СолоненкоЛСЛ. І. Солоненко
- Yu.S. VoronkoYVYu.S. Voronko
- A.P. BilyiABA.P. Bilyi
- T.V. KimstachTKT.V. Kimstach
Open Access
- 2 November 2025
- journal article
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Ukrainian Journal of Civil Engineering and Architecture
- No. 5 (029),p. 132-139
Abstract
Bronzes, due to their properties, are increasingly widely used in various industries every year. Due to the complexity of the operating conditions of technical devices and the growing requirements for the durability and reliability of materials, there is a need to use bronzes with an expanded number of preferential properties. The solution to this problem, where the result will be a combination of the desired levels of mechanical, technological and operational properties in one copper-tin alloy, should be sought in the direction of developing new systems for their alloying. The presented data indicate that bronzes of the Cu–Sn–Si system can combine the best properties inherent in both tin and silicon bronzes. This makes them promising for applications where high mechanical characteristics, corrosion resistance, good machinability and formability are important. However, tin-silicon bronzes have not been sufficiently studied and are not provided for by regulations. For this reason, tin-silicon bronzes do not have wide industrial distribution and, as a result, do not receive due research attention. Based on the above, the work devoted to establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents is relevant. Purpose of the study Establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents. Research methodology. The work analyzed foundry tin bronzes according to ASTM B505 and EN 1982. Samples for research (Æ16´100 мм) were made by pouring molten bronze into a sand casting mold. The initial charge materials of technical purity were used to manufacture the bronzes. Melting was carried out in an induction furnace with a graphite crucible under a layer of charcoal. The chemical composition of the bronzes was determined on the EXPERT 4L instrument. Microstructural studies were carried out on sections prepared by standard methods in accordance with the requirements of ASTM E3-11(2017) “Standard Guide for Preparation of Metallographic Specimens”. The structure was studied using a NEOPHOT 21 optical microscope with a magnification of 100 to 1000. Conclusions. Metallographic studies of the structure formation of alloys of the ternary system Cu‒Sn‒Si established the regularities of phase transformations of alloys of the copper corner of its conoid triangle. We received further development of the idea of the effect of doping tin bronze with silicon.Keywords
This publication has 9 references indexed in Scilit:
- Effect of Alloying Additives and Moulding Technology on Microstructure, Tightness, and Mechanical Properties of CuSn10 BronzeMaterials, 2023
- The Influence of Solidification Rate on HightinBronze MicrostructureArchives of Foundry Engineering, 2023
- Structural formation regularity of Cu-Sn-Si system low-tin «singing» bronze2022
- INVESTIGATION OF IMPURITIES IN BRONZE BrO3A3 INFLUENCE ON ITS MECHANICAL PROPERTIESTheory and practice of metallurgy, 2021
- Electrochemical and passive behaviour of Cu–Sn bronze in simulated archaeological soil mediaMaterials and Corrosion, 2020
- The Evaluation of Mechanical Properties of High-tin BronzesArchives of Foundry Engineering, 2017
- EFFECTS OF MICROSTRUCTURE AND CHEMICAL COMPOSITION ON STRENGTH AND IMPACT TOUGHNESS OF TIN BRONZESMM Science Journal, 2009
- Processing of Al-45Sn-10Cu Based Immiscible Alloy by a Rheomixing ProcessSolid State Phenomena, 2008
- Liquid demixing and microstructure formation in ternary Al–Sn–Cu alloysMaterials Science and Engineering: A, 2008