K.і. Uzlov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
K.і. Uzlov has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Lyudmila Solonenko
Odesa Polytechnic National University (Odesa, Ukraine)
2 shared publications - Sergei Repyakh
Ukrainian State University of Science and Technologies
2 shared publications T.V. Kimstach
2 shared publications- A.M. Kovzik1 shared publication
A.P. Bilyi
1 shared publication- Lyudmila Solonenko
Національний університет «Одеська політехніка
1 shared publication
Latest Publications
- Open Access
- 2 November 2025
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Ukrainian Journal of Civil Engineering and Architecture
- No. 5 (029),p. 132-139
ANALYSIS OF REGULATORY REQUIREMENTS AND PHASE EQUILIBRIUM DIAGRAMS OF BRONZES OF THE Cu‒Sn‒Si SYSTEM
Bronzes, due to their properties, are increasingly widely used in various industries every year. Due to the complexity of the operating conditions of technical devices and the growing requirements for the durability and reliability of materials, there is a need to use bronzes with an expanded number of preferential properties. The solution to this problem, where the result will be a combination of the desired levels of mechanical, technological and operational properties in one copper-tin alloy, should be sought in the direction of developing new systems for their alloying. The presented data indicate that bronzes of the Cu–Sn–Si system can combine the best properties inherent in both tin and silicon bronzes. This makes them promising for applications where high mechanical characteristics, corrosion resistance, good machinability and formability are important. However, tin-silicon bronzes have not been sufficiently studied and are not provided for by regulations. For this reason, tin-silicon bronzes do not have wide industrial distribution and, as a result, do not receive due research attention. Based on the above, the work devoted to establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents is relevant. Purpose of the study Establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents. Research methodology. The work analyzed foundry tin bronzes according to ASTM B505 and EN 1982. Samples for research (Æ16´100 мм) were made by pouring molten bronze into a sand casting mold. The initial charge materials of technical purity were used to manufacture the bronzes. Melting was carried out in an induction furnace with a graphite crucible under a layer of charcoal. The chemical composition of the bronzes was determined on the EXPERT 4L instrument. Microstructural studies were carried out on sections prepared by standard methods in accordance with the requirements of ASTM E3-11(2017) “Standard Guide for Preparation of Metallographic Specimens”. The structure was studied using a NEOPHOT 21 optical microscope with a magnification of 100 to 1000. Conclusions. Metallographic studies of the structure formation of alloys of the ternary system Cu‒Sn‒Si established the regularities of phase transformations of alloys of the copper corner of its conoid triangle. We received further development of the idea of the effect of doping tin bronze with silicon.
- 2 November 2025
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Ukrainian Journal of Civil Engineering and Architecture
- No. 5 (029),p. 132-139
Open AccessANALYSIS OF REGULATORY REQUIREMENTS AND PHASE EQUILIBRIUM DIAGRAMS OF BRONZES OF THE Cu‒Sn‒Si SYSTEM
Bronzes, due to their properties, are increasingly widely used in various industries every year. Due to the complexity of the operating conditions of technical devices and the growing requirements for the durability and reliability of materials, there is a need to use bronzes with an expanded number of preferential properties. The solution to this problem, where the result will be a combination of the desired levels of mechanical, technological and operational properties in one copper-tin alloy, should be sought in the direction of developing new systems for their alloying. The presented data indicate that bronzes of the Cu–Sn–Si system can combine the best properties inherent in both tin and silicon bronzes. This makes them promising for applications where high mechanical characteristics, corrosion resistance, good machinability and formability are important. However, tin-silicon bronzes have not been sufficiently studied and are not provided for by regulations. For this reason, tin-silicon bronzes do not have wide industrial distribution and, as a result, do not receive due research attention. Based on the above, the work devoted to establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents is relevant. Purpose of the study Establishing the regularities of phase transformations and structure formation in bronzes of the Cu–Sn–Si system with different silicon and tin contents. Research methodology. The work analyzed foundry tin bronzes according to ASTM B505 and EN 1982. Samples for research (Æ16´100 мм) were made by pouring molten bronze into a sand casting mold. The initial charge materials of technical purity were used to manufacture the bronzes. Melting was carried out in an induction furnace with a graphite crucible under a layer of charcoal. The chemical composition of the bronzes was determined on the EXPERT 4L instrument. Microstructural studies were carried out on sections prepared by standard methods in accordance with the requirements of ASTM E3-11(2017) “Standard Guide for Preparation of Metallographic Specimens”. The structure was studied using a NEOPHOT 21 optical microscope with a magnification of 100 to 1000. Conclusions. Metallographic studies of the structure formation of alloys of the ternary system Cu‒Sn‒Si established the regularities of phase transformations of alloys of the copper corner of its conoid triangle. We received further development of the idea of the effect of doping tin bronze with silicon.
- Open Access
- 28 September 2024
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Ukrainian Journal of Civil Engineering and Architecture
- No. 4 (022),p. 134-141
FOUNDRY TRIBOTECHNICAL BRONZE BrO3A3 CORROSION RESISTANCE INVESTIGATION
Problem statement. Bronzes have been and remain the main material for friction bearings, anti-friction and corrosion-resistant parts manufacturing that work under high loads, chemically active aggression influence at low and elevated temperatures, in cavitation, erosion, etc. conditions. That is, technology continuous development requires from anti-friction bronzes constant their corrosion resistance increasing, as a factor that will allow to significantly expand their application scope and increase cast products from them durability and reliability. The purpose of the articles. Based on relationship between corrosion damages and chemical composition analysis, compare BrO3A3 bronze corrosion resistance with BrA5, BrA9Zh3L and BrO5Tz5C5 bronzes corrosion resistance as the materials most often used in industry for parts manufacturing that work in friction nodes and chemically active environments. Methodology. Alloys for samples production have been prepared by technical purity primary charge materials fusing. Melting has been carried out in induction crucible furnace using a graphite crucible and charcoal as a coating material. Cast bronze samples corrosion resistance studies have been carried out in accordance with ISO 7384:2001, ISO 11845:1995 and GOST 9.308-85 requirements. Studied samples corrosion resistance has been evaluated based on the results of their relative weight loss during exposure for 90 days in climate chamber at relative humidity of 93 ± 3 % and temperature of 40 ± 2 °С, in sea and fresh water with temperature of 20...22 °С. Conclusions. BrO3A3 bronze, among the studied foundry bronzes, is characterized by the best level of anti-corrosion properties in all environments used in this research. In this regard, it is a reason to recommend the studied bronze for tribotechnical purpose cast parts manufacturing, which work in air, fresh or sea water.
- 28 September 2024
- Published by SHEE Prydniprovska State Academy of Civil Engineering and Architecture in Ukrainian Journal of Civil Engineering and Architecture
- No. 4 (022),p. 134-141
Open AccessFOUNDRY TRIBOTECHNICAL BRONZE BrO3A3 CORROSION RESISTANCE INVESTIGATION
Problem statement. Bronzes have been and remain the main material for friction bearings, anti-friction and corrosion-resistant parts manufacturing that work under high loads, chemically active aggression influence at low and elevated temperatures, in cavitation, erosion, etc. conditions. That is, technology continuous development requires from anti-friction bronzes constant their corrosion resistance increasing, as a factor that will allow to significantly expand their application scope and increase cast products from them durability and reliability. The purpose of the articles. Based on relationship between corrosion damages and chemical composition analysis, compare BrO3A3 bronze corrosion resistance with BrA5, BrA9Zh3L and BrO5Tz5C5 bronzes corrosion resistance as the materials most often used in industry for parts manufacturing that work in friction nodes and chemically active environments. Methodology. Alloys for samples production have been prepared by technical purity primary charge materials fusing. Melting has been carried out in induction crucible furnace using a graphite crucible and charcoal as a coating material. Cast bronze samples corrosion resistance studies have been carried out in accordance with ISO 7384:2001, ISO 11845:1995 and GOST 9.308-85 requirements. Studied samples corrosion resistance has been evaluated based on the results of their relative weight loss during exposure for 90 days in climate chamber at relative humidity of 93 ± 3 % and temperature of 40 ± 2 °С, in sea and fresh water with temperature of 20...22 °С. Conclusions. BrO3A3 bronze, among the studied foundry bronzes, is characterized by the best level of anti-corrosion properties in all environments used in this research. In this regard, it is a reason to recommend the studied bronze for tribotechnical purpose cast parts manufacturing, which work in air, fresh or sea water.
- Open Access
- 1 September 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 30 (2) , 59-71
Influence of mold and aluminum bronze melt overheating on castings structure and their surface quality
Influence of mold and aluminum bronze melt overheating on castings structure and their surface quality
- 1 September 2022
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 30 (2) , 59-71
Open AccessInfluence of mold and aluminum bronze melt overheating on castings structure and their surface quality
Influence of mold and aluminum bronze melt overheating on castings structure and their surface quality
- Open Access
- 20 December 2021
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 29 (4) , 67-77
Influence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality
Influence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality
- 20 December 2021
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 29 (4) , 67-77
Open AccessInfluence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality
Influence of sand-sodium-silicate mixtures structured by steam-microwave solidification method on small castings quality