Low-Dimensionalization Experiments on Porous Cathodes and Analysis of Oxygen Transport and Reaction Distributions Toward High-Power Lithium-Air Batteries
Lithium-air batteries (LABs), with their exceptionally high theoretical energy density, are considered promising candidates for next-generation energy storage[1]. However, LABs still have many challenges in terms of improving cycle characteristics and increasing power output. Currently, it is difficult to supply sufficient oxygen to the cathode reaction surface, preventing the realization of high-power output. In typical LAB designs employing porous cathodes, oxygen must diffuse through narrow, electrolyte-filled pores [2, 3]. Due to its low solubility and diffusivity in the electrolyte, oxygen transport is significantly limited. Oxygen transport phenomena within the pores are considered to affect the discharge characteristics of the cathode; however, the detailed mechanisms remain unclear. In this study, we investigated fundamental discharge characteristics of LABs by using a low-dimensionalized cathode that mimics the oxygen transport phenomena in a porous cathode. The approach was based on a combination of experimental discharge tests and analysis using a transmission line model. The distributions of oxygen concentration in the electrolyte of the low-dimensional cathode and current density distribution on the reaction surface were investigated. Figure 1 shows the concept of low-dimensionalization and the structure of the cell used in the experiments of this study. To isolate and study these phenomena, a custom experimental setup was fabricated using flat glassy carbon (GC) plates. By covering part of the GC plate with resin and alkaline-resistant tape the area available for oxygen dissolution into the electrolyte was restricted. This configuration enabled analysis to focus on the transport properties within the pores of the porous cathode. By varying the thickness and number of tape layers, the area available for oxygen dissolution was controlled. This configuration enabled the investigation of how the size of the oxygen supply area affects discharge performance. As a result of discharge tests, in cathodes without restriction of the oxygen dissolution area, the decrease in cathode potential was gradual even under high current conditions. It is due to the easy supply of oxygen from the atmosphere to the reaction surface. In contrast, when the oxygen dissolution area was restricted, the cathode potential dropped sharply with increasing current. This behavior is caused by a significant increase in concentration overpotential resulting from the limited oxygen supply, and similar behavior is expected to occur in porous cathodes with small pores. To analyze these experimental results, a transmission line model incorporating the Butler–Volmer equation and Fick's law was constructed. The model assumes a uniform potential distribution on the cathode reaction surface and calculates the local current density as a function of the overpotential and oxygen concentration. This model also takes into account the rate of oxygen dissolution at the electrolyte interface. By fitting the main parameters, the simulation results showed good agreement with the experimental data, as illustrated in the Figure 2 particularly in the high-current region where the cathode potential drops sharply. Using this model, the reaction distribution and oxygen concentration distribution were calculated. As shown in Figure 3, when the current is low (2 mA), oxygen is transported to a depth of approximately 2 mm into the cathode, and the reaction distribution remains relatively uniform. In contrast, when the current is increased to 5 mA, oxygen is transported only to a depth of around 0.4 mm, and the oxygen concentration near the interface falls below the saturation concentration. These results suggest that the rate of oxygen dissolution becomes the limiting factor for discharge performance under higher current conditions. References [1] Girishkumar, G., McCloskey, B., Luntz, A. C., Swanson, S., Wilcke, W., “Lithium−air battery: promise and challenges,” J. Phys. Chem. Lett., 1(14), pp 2193–2203, (2010). [2] Shibata, K., Uemura, S., Tsushima, S., Hirai, S., “Reaction and mass transport simulations by LBM in electrolyte of aqueous lithium-air battery,”ECS Trans. , 64(19), pp 39-46, (2015). [3] Fujimoto, S., Uemura, S., Imanihsi, N., Hirai, S., “Oxygen concentration measurement in the porous cathode of a lithium-air battery using a fine optical fiber sensor,”Mechanical Engineering Letters , 5, pp 19-00095, (2019). Figure 1