In situ high-pressure and high-temperature X-ray microtomographic imaging during large deformation: A new technique for studying mechanical behavior of multiphase composites
Authors:
- Yanbin WangYWYanbin Wang
- Charles LesherCLCharles Lesher
- Guillaume FiquetGFGuillaume Fiquet
- Mark L. RiversMRMark L. Rivers
- Norimasa NishiyamaNNNorimasa Nishiyama
- Julien SiebertJSJulien Siebert
- Jeffery RobertsJRJeffery Roberts
- Guillaume MorardGMGuillaume Morard
- Alisha ClarkACAlisha Clark
- Heather WatsonHWHeather Watson
- Nicolas MenguyNMNicolas Menguy
Open Access
- 1 February 2011
- journal article
- Published by Geological Society of America in Geosphere
- Vol. 7 (1) , 40-53
Abstract
International audiencemicrostructural evolution of a two-phase composite (olivine + Fe-Ni-S) during large shear deformation, using a newly developed high-pressure X-ray tomography microscope. Two samples were examined: a load-bearing framework-type texture, where the alloy phase (Fe-Ni-S) was present as isolated spherical inclusions, and an interconnected network-type texture, where the alloy phase was concentrated along the silicate grain boundaries and tended to form an interconnected network. The samples, both containing ~10 vol% alloy inclusions, were compressed to 6 GPa, followed by shear deformation at temperatures up to 800 K. Shear strains were introduced by twisting the samples at high pressure and high temperature. At each imposed shear strain, samples were cooled to ambient temperature and tomographic images collected. The three-dimensional tomographic images were analyzed for textural evolution. We found that in both samples, Fe-Ni-S, which is the weaker phase in the composite, underwent signifi cant deformation. The resulting lens-shaped alloy phase is subparallel to the shear plane and has a laminated, highly anisotropic interconnected weak layer texture. Scanning electron microscopy showed that many alloy inclusions became fi lm-like, with thicknesses <1 m, suggesting that Fe- Ni-S was highly mobile under nonhydrostatic stress, migrated into silicate grain bound aries, and propagated in a manner similar to melt inclusions in a deforming solid matrix. The grain size of the silicate matrix was signifi cantly reduced under large strain deformation. The strong shape-preferred orientation thus developed can profoundly influence a composite's bulk elastic and rheological properties. High-pressure-high temperature tomography not only provides quantitative observations on textural evolution, but also can be compared with simulation results to derive more rigorous models of the mechanical properties of composite materials relevant to Earth's deep mantleKeywords
This publication has 67 references indexed in Scilit:
- Large-strain deformation and strain partitioning in polyphase rocks: Dislocation creep of olivine–magnesiowüstite aggregatesTectonophysics, 2006
- The strength of Mg0.9Fe0.1SiO3 perovskite at high pressure and temperatureNature, 2002
- Plastic deformation and development of clinopyroxene lattice preferred orientations in eclogitesJournal of Structural Geology, 2002
- Computation of linear elastic properties from microtomographic images: Methodology and agreement between theory and experimentGeophysics, 2002
- Experimental investigation into the microstructural and mechanical evolution of phyllosilicate-bearing fault rock under conditions favouring pressure solutionJournal of Structural Geology, 2001
- An interconnected network of core-forming melts produced by shear deformationNature, 2000
- Anisotropic parameters of layered media in terms of composite elastic propertiesGeophysics, 1995
- Analogue experiments and numerical modelling on the relation between microgeometry and flow properties of polyphase materialsMaterials Science and Engineering: A, 1994
- Wolff’s Law of Trabecular Architecture at Remodeling EquilibriumJournal of Biomechanical Engineering, 1986
- Steady state flow of rocksReviews of Geophysics, 1976