NNNorimasa Nishiyama

Norimasa Nishiyama

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Norimasa Nishiyama has a total of 144 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Low-temperature thermal expansion of the α and ω phases of titanium

    by Norimasa Nishiyama, Atsushi Togo, Yoshitaka Matsushita

    We investigated the low-temperature thermal expansion of the α phase and the ω phase, a high-pressure polymorph of titanium, by X-ray diffraction measurements from approximately 5 to 300 K, together with first-principles calculations. Single-phase bulk polycrystalline ω-Ti was synthesized at 7.7 GPa and 500 °C and recovered to ambient pressure. Although the two phases exhibit very similar volumetric thermal expansion, their axial responses are markedly different. In α-Ti, the c-axis thermal expansion coefficient becomes negative below approximately 50 K and reaches a minimum of -0.71 × 10-6 K-1 at 20 K. Both experiment and theory indicate substantially smaller c-axis negative thermal expansion than previously reported from single-crystal length measurements. In contrast, ω-Ti expands nearly isotropically along the a and c axes, and its c/a ratio remains nearly temperature independent and close to the ideal bcc-derived value. The c/a ratio of α-Ti decreases with increasing temperature. Debye-Grüneisen analysis yielded Debye temperatures of 427 ± 5 K and 409 ± 12 K and effective Grüneisen parameters of 1.33 ± 0.04 and 1.23 ± 0.04 for α-Ti and ω-Ti, respectively. The first-principles calculations reproduce the volumetric thermal expansion of both phases and capture the overall trends of their axial responses.

  • Open Access

    Ultrahigh flow strength in shocked nanopolycrystalline diamond

    by Anirudh Hari, Kento Katagiri, Wanghui Li, Dorian P. Luccioni, Rayen Lin, Sophie E. Parsons, Zipeng Xu, Rohit Hari, Tharun Reddy, Ernest W. Cubit, et al.

    Extreme pressures and temperatures create conditions that allow even hard and brittle materials to flow plastically. Despite extensive research, the limits of flow strength under such conditions remain uncertain, and the mechanisms driving deformation at the relevant stresses are a subject of debate. Using femtosecond in situ x-ray diffraction experiments and large-scale molecular dynamics simulations, we demonstrate that stacking fault-mediated strengthening enables shock-compressed nanopolycrystalline diamond to achieve a peak flow strength of 92 ± 3 GPa at a stress of 212 ± 6 GPa. Our findings show that extreme conditions can unlock ultrahigh strength via a complex array of competing deformation mechanisms and thermodynamic effects.

  • Open Access

    High tensile strength and transformation-induced plasticity in bulk polycrystalline omega titanium

    by Norimasa Nishiyama, Yoshinori Tange, Takashi Sawahata, Masafumi Matsushita, Kazuya Tokuda, Kosuke Tominaga, Takashi Sekiya, Koji Kuramochi, Keita Sasaki, Fumihiro Wakai, et al.

    Titanium and its alloys exhibit advantageous ductility and strength-to-weight ratios, which makes them suitable for use as structural materials in numerous industrial applications. The wphase has been observed to precipitate during the aging process of titanium alloys, resulting in a loss of ductility. Here we report tensile behavior of bulk polycrystalline w-titanium with a chemical composition of commercially pure titanium grade 4 and an average grain size of 3.4 mm. We observed that stress-induced w → α martensitic phase transformation occurs exclusively in the plastic regime. As plastic deformation proceeds, the volume fraction of a-phase increases. The 0.2% offset yield strength, tensile strength, and elongation to failure were determined to be 1130 ± 30 MPa, 1220 ± 30 MPa, and 16 ± 2 %, respectively. These mechanical properties are comparable to those of a titanium alloy Ti-6Al-4V. The present study revealed transformation-induced plasticity in bulk polycrystalline w-titanium.

  • Open Access

    High Compressive Strength of Bulk Polycrystalline ω Phase in Pure Titanium

    by Takashi Sawahata, Norimasa Nishiyama, Makoto Arita, Yuki Kawabata, Masafumi Matsushita, Koji Ohara, Yuji Higo, Fumihiro Wakai, Zenji Horita

    Titanium has the highest strength-to-weight ratio of any metal. Titanium and its alloys are strong and lightweight, and are therefore used in many industrial applications. The ω-phase is known to form metastably during quenching and aging processes of titanium alloys, and the presence of this phase causes increases in strength and decreases in ductility. However, the mechanical properties of the ω-phase are poorly measured because this phase precipitates as nanograins in titanium alloys. Here we report the fabrication of bulk polycrystalline ω-phase samples in pure titanium under high pressure and temperature conditions of 12 GPa and 400°C. They are single-phase and randomly oriented polycrystalline materials with an average grain size of 21 ± 8 μm. The 0.2% offset yield strength was determined from compressive stress-strain curves to be 913 ± 3 MPa. The ω-phase is more than twice as strong as the α-phase in pure titanium and could be used as a non-toxic structural material for biomedical applications.


  • Open Access

    Extreme conditions research using the large-volume press at the P61B endstation, PETRA III

    by Robert Farla, Shrikant Bhat, Stefan Sonntag, Artem Chanyshev, Shuailing Ma, Takayuki Ishii, Zhaodong Liu, Adrien Néri, Norimasa Nishiyama, Guilherme Abreu Faria, et al.

    Penetrating, high-energy synchrotron X-rays are in strong demand, particularly for high-pressure research in physics, chemistry and geosciences, and for materials engineering research under less extreme conditions. A new high-energy wiggler beamline P61 has been constructed to meet this need at PETRA III in Hamburg, Germany. The first part of the paper offers an overview of the beamline front-end components and beam characteristics. The second part describes the performance of the instrumentation and the latest developments at the P61B endstation. Particular attention is given to the unprecedented high-energy photon flux delivered by the ten wigglers of the PETRA III storage ring and the challenges faced in harnessing this amount of flux and heat load in the beam. Furthermore, the distinctiveness of the world's first six-ram Hall-type large-volume press, Aster-15, at a synchrotron facility is described for research with synchrotron X-rays. Additionally, detection schemes, experimental strategies and preliminary data acquired using energy-dispersive X-ray diffraction and radiography techniques are presented.


  • Mechanics of shape evolution of particle aggregates in viscous sintering

    by Fumihiro Wakai, Yuta Numanami, Tomoki Sekiya, Norimasa Nishiyama


  • Low temperature heat capacity measurements of β-Si3N4 and γ-Si3N4: Determination of the equilibrium phase boundary between β-Si3N4 and γ-Si3N4

    by Norimasa Nishiyama, Suguru Kitani, Yuki Ohta, Eleonora Kulik, Zuzana Netriová, Astrid Holzheid, Zoltán Lenčéš, Hitoshi Kawaji, Fumihiro Wakai


  • Elasticity of nanocrystalline kyanite at high pressure and temperature from ultrasonic and synchrotron X‐ray techniques

    by Nico Alexander Gaida, Steeve Gréaux, Yoshio Kono, Hiroaki Ohfuji, Hideharu Kuwahara, Norimasa Nishiyama, Oliver Beermann, Takuya Sasaki, Ken Niwa, Masashi Hasegawa

    Material properties, such as elasticity data at wide‐ranging conditions of pressure and temperature, attract increasing attention for material and earth sciences. In particular, polycrystalline ceramics for next‐generation photonic applications are nowadays fabricated by advanced syntheses techniques operating under elevated pressures and temperatures. Herein, the elastic properties of a synthetic transparent and reinforced aluminosilicate nanoceramic composed of triclinic kyanite with minor amounts of trigonal α‐alumina crystals are investigated using in situ synchrotron X‐ray diffraction and ultrasonic techniques at high‐pressure (up to 11 GPa) and high‐temperature (300‐1500 K) conditions. This not only enables the determination of the equation of state (EoS) parameters by applying the pressure‐volume‐temperature ( P ‐ V ‐ T ) data to the high‐temperature Birch‐Murnaghan EoS but also yields the elastic moduli together with their P and T derivatives from the fit of the compressional and shear wave velocities to a finite strain EoS: K S 0,300 = 186(2) GPa, K ′ S 0,300 = 7.2(6), (∂ K S 0,300 /∂ T ) P = −0.023(2) GPa K −1 , G 0,300 = 125(1) GPa G ′ 0,300 = 2.3(2), (∂ G 0,300 /∂ T ) P = −0.017(1) GPa K −1 . On the basis of our acquired results, we propose to predict the elastic moduli of aluminosilicate ceramics by a linear function of the ratio of AlO 6 octahedra and SiO 4 tetrahedra within the constituting phases.


  • Open Access

    Microstructural effects on hardness and optical transparency of birefringent aluminosilicate nanoceramics

    by Nico A. Gaida, Norimasa Nishiyama, Oliver Beermann, Ulrich Schürmann, Atsunobu Masuno, Christopher Giehl, Ken Niwa, Masashi Hasegawa, Shrikant Bhat, Robert Farla, et al.

    Transparent nanoceramics, synthesized at extreme conditions of high pressure and temperature, are new classes of materials highly attractive for photonic applications, such as optical windows, which require additional increased hardness and toughness. In this study, mechanical properties of transparent polycrystalline nanoceramics consisting of triclinic Al2SiO5 kyanite (~91.4 vol%) and trigonal Al2O3 corundum (~8.6 vol%) fabricated at high pressure (10 GPa) and temperature (1200‐1400°C) were investigated. It is already known that the optical transparency of kyanite‐based nanoceramics increases with decreasing average grain size. The present study shows that the hardness of these ceramics increases with decreasing grain sizes down to ~70 nm according to the Hall‐Petch strengthening. This grain size seems to mark a transition range where an inverse Hall‐Petch effect is indicated due to signs of a moderate hardness decrease at a smaller grain size of ~35 nm. The observed hardness‐grain size relation can fairly be described by an existing composite model, which considers the crystals to be harder than the noncrystalline grain boundaries. Within the range of average grain sizes examined, the kyanite habit changes from more equant to more columnar. This behavior is associated with the observed strong crack deflection by the columnar kyanite grains with aspect (length to diameter) ratios ranging from ~2 to 10 and may positively affect the fracture toughness.


  • Thermal expansion and P-V-T equation of state of cubic silicon nitride

    by Norimasa Nishiyama, Kotaro Fujii, Eleonora Kulik, Masahiro Shiraiwa, Nico A. Gaida, Yuji Higo, Yoshinori Tange, Astrid Holzheid, Masatomo Yashima, Fumihiro Wakai