Microstructure, phase transformation temperatures and long-term stability of ex-situ Alloy 718 + TiB2 metal-ceramic nanocomposites as a repair coatings for aerospace applications
Open Access
- 26 November 2025
- journal article
- research article
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Abstract
In this study, Ni-based superalloy Alloy 718 + xTiB2 (x = 1.25; 2.5; 3.75; 5.0%) composites were fabricated by suction casting to improve hardness, wear resistance, and corrosion resistance. The microstructure and properties were analyzed using synchrotron X-ray diffraction, light microscopy, scanning electron microscopy, scanning transmission electron microscopy, dilatometry, differential scanning calorimetry, Vickers hardness, wear resistance measurements, and corrosion tests. The results show that the addition of TiB2 to Alloy 718 has a strong influence on the primary microstructure. All composites are characterized by a dendritic microstructure with irregular distribution of strengthening precipitates. In the reference Alloy 718, the dendritic regions consist of the γ-phase, while interdendritic areas contain Nb-rich carbides and Laves phase precipitates. The TiB2 particles added to a powder mixture reacts strongly with the liquid Alloy 718 during suction casting, resulting in the decrease of the Laves phase and the formation of the M3B2 and M23B6 phases. Increasing the initial TiB2 content shifted the phase transformation temperatures (solidus and liquidus) to lower temperatures. Hardness values increased significantly from 198 HV10 in the reference Alloy 718 to 403 HV10 (5.0% TiB2), which contributed to improved wear resistance. Finally, high temperature exposures in rich oxygen atmosphere (steam) and reduced oxygen atmosphere (Ar + 0.25 vol% SO2) at 704 °C for 1000 h indicated that the Alloy 718 + TiB2 composites were characterized by a lower mass gain than the reference Alloy 718.Keywords
Funding Information
- Narodowe Centrum Badań i Rozwoju (0036/L-13/2022)
This publication has 65 references indexed in Scilit:
- Adaptive Phase or Variant Formation at the Austenite/Twinned Martensite Interface in Modulated Ni–Mn–Ga MartensiteAdvanced Functional Materials, 2024
- Review of Microstructure–Mechanical Property Relationships in Cast and Wrought Ni‐Based Superalloys with Boron, Carbon, and Zirconium Microalloying AdditionsAdvanced Engineering Materials, 2022
- Evolution of Microstructure and Mechanical Properties of ATI 718Plus® Superalloy After Graded Solution TreatmentMetallurgical and Materials Transactions A, 2022
- Solid-State Phase Transformations Involving (Nb,Mo)2CrB2 Borides and (Nb,Ti)2CS Carbosulfides at the Grain Boundaries of Superalloy Inconel 718Metallurgical and Materials Transactions A, 2020
- Phase Investigations Under Steam Oxidation Process at 800 °C for 1000 h of Advanced Steels and Ni-Based AlloysOxidation of Metals, 2016
- Modelling the coefficient of thermal expansion in Ni-based superalloys and bond coatingsJournal of Materials Science, 2016
- Investigation of Oxide Inclusions and Primary Carbonitrides in Inconel 718 Superalloy Refined through Electroslag Remelting ProcessMetallurgical and Materials Transactions B, 2012
- Chromium Volatilization Rates from Cr2O3 Scales into Flowing Gases Containing Water VaporOxidation of Metals, 2006
- Wetting of Group IV diborides by liquid metalsJournal of Materials Science, 2006
- Transactions and CommunicationsJournal of the Society of Chemical Industry, 1944