Łukasz Rakoczy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Łukasz Rakoczy has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
Rafał Cygan
16 shared publications- Małgorzata Grudzień-Rakoczy
Łukasiewicz Research Network-Kraków Institute of Technology, Kraków, Poland
12 shared publications Małgorzata Grudzień-Rakoczy
10 shared publications- Tomasz Kargul
Faculty of Metals Engineering and Industrial Computer Science, AGH University of Science and Technology, Krakow, Poland
8 shared publications Anna Zielińska-Lipiec
Faculty of Metals Engineering and Industrial Computer Science, AGH University of Krakow, Kraków, Poland
7 shared publications- Grzegorz Cempura
Faculty of Metals Engineering and Industrial Computer Science, AGH University of Krakow, Kraków, Poland
7 shared publications
Latest Publications
- Open Access
- 5 March 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1181, 19-24
Influence of the Preheat Temperature and Withdrawal Rate on the Microstructure of Ceramic-Cored Ds MAR-M247 Nickel-Based Superalloy
The research focuses on cored blades made from the MAR-M247® Ni-based superalloy, which were manufactured through directional solidification with varying withdrawal rates of either 3.4 mm/min or 5.0 mm/min, and shell mold temperatures of 1510 °C or 1566 °C after undergoing solution heat treatment. The characterization of four variants of the cored blades was conducted using several analytical techniques: X-ray diffraction (XRD), light microscopy (LM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). The XRD analysis identified the presence of the γ matrix, the intermetallic γ' phase, MC carbides, and M 5 B 3 phases. The dendritic regions of the cored blades consist of secondary γ' precipitates surrounded by a γ matrix, with a mean size ranging from 0.264 to 0.272 μm, depending on the fabrication parameters.
- 5 March 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1181, 19-24
Open AccessInfluence of the Preheat Temperature and Withdrawal Rate on the Microstructure of Ceramic-Cored Ds MAR-M247 Nickel-Based Superalloy
The research focuses on cored blades made from the MAR-M247® Ni-based superalloy, which were manufactured through directional solidification with varying withdrawal rates of either 3.4 mm/min or 5.0 mm/min, and shell mold temperatures of 1510 °C or 1566 °C after undergoing solution heat treatment. The characterization of four variants of the cored blades was conducted using several analytical techniques: X-ray diffraction (XRD), light microscopy (LM), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDX). The XRD analysis identified the presence of the γ matrix, the intermetallic γ' phase, MC carbides, and M 5 B 3 phases. The dendritic regions of the cored blades consist of secondary γ' precipitates surrounded by a γ matrix, with a mean size ranging from 0.264 to 0.272 μm, depending on the fabrication parameters.
- Open Access
- 5 January 2026
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (5) , 2243-2266
Investigation of the As-Cast Microstructure, Stability, Wear and Corrosion Resistance of Alloy 625 + WC Nanocomposites Processed Through Suction Casting as Repair Materials for Ni-Based Superalloys
While maintenance, repair, and operations are crucial for improving the performance of gas turbine components, the properties of filler metal, such as Inconel alloys, may be insufficient in extremely harsh environments, necessitating the use of alternative materials need to be implemented. In this study, Alloy 625-based composites reinforced with varying WC (tungsten carbides) nanoparticles (1.25, 2.5, 3.75, or 5.0 wt pct) were fabricated via suction casting. The dendrites in both Alloy 625 and the WC-reinforced nanocomposites consisted of the γ matrix, and segregation of alloying elements in the interdendritic regions resulted in additional carbides and Laves phase precipitates were additionally observed. Synchrotron radiation experiments and microstructure investigations revealed that the partial dissolution of WC promoted the formation of Nb-rich MC and Mo, W-rich M 6 C carbides, while simultaneously reducing the volume fraction of Laves phase precipitates. Oxidation tests in steam (704 °C/1000 hours) showed that the Alloy 625 + WC nanocomposites exhibited slightly lower mass gain compared to the reference Alloy 625. In contrast, in the Ar + 0.25 pct SO 2 atmosphere, increasing WC content in Alloy 625 negatively affects the corrosion resistance due to the excessive formation of Ni 3 S 2 . The hardness of Alloy 625, initially measured at 201 HV10, increased to 254 HV10 with the addition of 5.0 pct WC, contributing to improved dry-sliding wear resistance.
- 5 January 2026
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 57 (5) , 2243-2266
Open AccessInvestigation of the As-Cast Microstructure, Stability, Wear and Corrosion Resistance of Alloy 625 + WC Nanocomposites Processed Through Suction Casting as Repair Materials for Ni-Based Superalloys
While maintenance, repair, and operations are crucial for improving the performance of gas turbine components, the properties of filler metal, such as Inconel alloys, may be insufficient in extremely harsh environments, necessitating the use of alternative materials need to be implemented. In this study, Alloy 625-based composites reinforced with varying WC (tungsten carbides) nanoparticles (1.25, 2.5, 3.75, or 5.0 wt pct) were fabricated via suction casting. The dendrites in both Alloy 625 and the WC-reinforced nanocomposites consisted of the γ matrix, and segregation of alloying elements in the interdendritic regions resulted in additional carbides and Laves phase precipitates were additionally observed. Synchrotron radiation experiments and microstructure investigations revealed that the partial dissolution of WC promoted the formation of Nb-rich MC and Mo, W-rich M 6 C carbides, while simultaneously reducing the volume fraction of Laves phase precipitates. Oxidation tests in steam (704 °C/1000 hours) showed that the Alloy 625 + WC nanocomposites exhibited slightly lower mass gain compared to the reference Alloy 625. In contrast, in the Ar + 0.25 pct SO 2 atmosphere, increasing WC content in Alloy 625 negatively affects the corrosion resistance due to the excessive formation of Ni 3 S 2 . The hardness of Alloy 625, initially measured at 201 HV10, increased to 254 HV10 with the addition of 5.0 pct WC, contributing to improved dry-sliding wear resistance.
- Open Access
- 16 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (4) , 4669-4686
As-cast microstructure, wear and oxidation resistance of Alloy 718+TiC nanocomposites processed via suction casting
- 16 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (4) , 4669-4686
Open AccessAs-cast microstructure, wear and oxidation resistance of Alloy 718+TiC nanocomposites processed via suction casting
- Open Access
- 26 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Microstructure, phase transformation temperatures and long-term stability of ex-situ Alloy 718 + TiB2 metal-ceramic nanocomposites as a repair coatings for aerospace applications
In this study, Ni-based superalloy Alloy 718 + xTiB2 (x = 1.25; 2.5; 3.75; 5.0%) composites were fabricated by suction casting to improve hardness, wear resistance, and corrosion resistance. The microstructure and properties were analyzed using synchrotron X-ray diffraction, light microscopy, scanning electron microscopy, scanning transmission electron microscopy, dilatometry, differential scanning calorimetry, Vickers hardness, wear resistance measurements, and corrosion tests. The results show that the addition of TiB2 to Alloy 718 has a strong influence on the primary microstructure. All composites are characterized by a dendritic microstructure with irregular distribution of strengthening precipitates. In the reference Alloy 718, the dendritic regions consist of the γ-phase, while interdendritic areas contain Nb-rich carbides and Laves phase precipitates. The TiB2 particles added to a powder mixture reacts strongly with the liquid Alloy 718 during suction casting, resulting in the decrease of the Laves phase and the formation of the M3B2 and M23B6 phases. Increasing the initial TiB2 content shifted the phase transformation temperatures (solidus and liquidus) to lower temperatures. Hardness values increased significantly from 198 HV10 in the reference Alloy 718 to 403 HV10 (5.0% TiB2), which contributed to improved wear resistance. Finally, high temperature exposures in rich oxygen atmosphere (steam) and reduced oxygen atmosphere (Ar + 0.25 vol% SO2) at 704 °C for 1000 h indicated that the Alloy 718 + TiB2 composites were characterized by a lower mass gain than the reference Alloy 718.
- 26 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessMicrostructure, phase transformation temperatures and long-term stability of ex-situ Alloy 718 + TiB2 metal-ceramic nanocomposites as a repair coatings for aerospace applications
In this study, Ni-based superalloy Alloy 718 + xTiB2 (x = 1.25; 2.5; 3.75; 5.0%) composites were fabricated by suction casting to improve hardness, wear resistance, and corrosion resistance. The microstructure and properties were analyzed using synchrotron X-ray diffraction, light microscopy, scanning electron microscopy, scanning transmission electron microscopy, dilatometry, differential scanning calorimetry, Vickers hardness, wear resistance measurements, and corrosion tests. The results show that the addition of TiB2 to Alloy 718 has a strong influence on the primary microstructure. All composites are characterized by a dendritic microstructure with irregular distribution of strengthening precipitates. In the reference Alloy 718, the dendritic regions consist of the γ-phase, while interdendritic areas contain Nb-rich carbides and Laves phase precipitates. The TiB2 particles added to a powder mixture reacts strongly with the liquid Alloy 718 during suction casting, resulting in the decrease of the Laves phase and the formation of the M3B2 and M23B6 phases. Increasing the initial TiB2 content shifted the phase transformation temperatures (solidus and liquidus) to lower temperatures. Hardness values increased significantly from 198 HV10 in the reference Alloy 718 to 403 HV10 (5.0% TiB2), which contributed to improved wear resistance. Finally, high temperature exposures in rich oxygen atmosphere (steam) and reduced oxygen atmosphere (Ar + 0.25 vol% SO2) at 704 °C for 1000 h indicated that the Alloy 718 + TiB2 composites were characterized by a lower mass gain than the reference Alloy 718.
- Open Access
Al and Cu Effect on the Microstructure and Mechanical Properties of HEA Based on the AlCoCuFeNi System
Three variants of high-entropy alloys (HEAs) from the AlCoCuFeNi group, containing different amounts of Al and Cu, were developed and produced via induction melting and casting into ceramic moulds. The ingots were homogenized at 1000 °C for 10 h. Analyses revealed that variations in Al and Cu concentrations led to significant changes in the material’s microstructure, hardness, strength, and impact strength. In the equiatomic variant, differential scanning calorimetry revealed a peak associated with the phase transformation, indicating that this alloy’s microstructure consists of two distinct phases. In contrast, when the concentrations of Al and Cu are reduced, a single-phase microstructure is observed. The equiatomic variant (used as a reference) is characterized by its hardness and brittleness, exhibiting slight ductility, with a tensile strength of 80 MPa, a hardness of 400 HV5, and an impact strength of 1.9 J/cm2. However, with adjusted Al contents of 1/2 and Cu contents of 1/4, the alloy displays exceptional strength combined with good plasticity, achieving a tensile strength of up to 450 MPa with 60% elongation, and an impact strength of 215 J/cm2. The non-equiatomic variants exhibit a comparatively more straightforward microstructure and enhanced ductility, which may facilitate easier processing of these alloys. Fractography investigation revealed a ductile mode of fracture in the samples.
Open AccessAl and Cu Effect on the Microstructure and Mechanical Properties of HEA Based on the AlCoCuFeNi System
Three variants of high-entropy alloys (HEAs) from the AlCoCuFeNi group, containing different amounts of Al and Cu, were developed and produced via induction melting and casting into ceramic moulds. The ingots were homogenized at 1000 °C for 10 h. Analyses revealed that variations in Al and Cu concentrations led to significant changes in the material’s microstructure, hardness, strength, and impact strength. In the equiatomic variant, differential scanning calorimetry revealed a peak associated with the phase transformation, indicating that this alloy’s microstructure consists of two distinct phases. In contrast, when the concentrations of Al and Cu are reduced, a single-phase microstructure is observed. The equiatomic variant (used as a reference) is characterized by its hardness and brittleness, exhibiting slight ductility, with a tensile strength of 80 MPa, a hardness of 400 HV5, and an impact strength of 1.9 J/cm2. However, with adjusted Al contents of 1/2 and Cu contents of 1/4, the alloy displays exceptional strength combined with good plasticity, achieving a tensile strength of up to 450 MPa with 60% elongation, and an impact strength of 215 J/cm2. The non-equiatomic variants exhibit a comparatively more straightforward microstructure and enhanced ductility, which may facilitate easier processing of these alloys. Fractography investigation revealed a ductile mode of fracture in the samples.
- Open Access
- 6 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 2820-2839
Microstructure and resultant properties of ex-situ Alloy 625+TiB2 nanocomposites processed via suction casting as filler material for Ni-based superalloys repair applications
- 6 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 2820-2839
Open AccessMicrostructure and resultant properties of ex-situ Alloy 625+TiB2 nanocomposites processed via suction casting as filler material for Ni-based superalloys repair applications
- Open Access
- 16 May 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1149, 109-114
Alloy 625+TiB2 Composites Fabricated via Suction Casting – Microstructure and Selected Properties
In this work, nanocomposites Alloy 625-xTiB2 (x=1.25; 2.5; 3.75; 5.0 wt%) were processed through suction casting. The microstructure and selected properties were analyzed using light microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. It has been observed that introducing TiB2 particles into Alloy 625 strongly influences the as-cast microstructure. A dendritic microstructure with irregular distribution of the strengthening precipitates has been revealed. In reference Alloy 625, the Nb-rich carbides and Laves phase precipitates exist in the interdendritic spaces. The TiB2 interacted with the liquid Alloy 625 during suction casting, leading to microstructural changes like more precipitates in interdendritic spaces including newly formed B-rich phases.
- 16 May 2025
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1149, 109-114
Open AccessAlloy 625+TiB2 Composites Fabricated via Suction Casting – Microstructure and Selected Properties
In this work, nanocomposites Alloy 625-xTiB2 (x=1.25; 2.5; 3.75; 5.0 wt%) were processed through suction casting. The microstructure and selected properties were analyzed using light microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. It has been observed that introducing TiB2 particles into Alloy 625 strongly influences the as-cast microstructure. A dendritic microstructure with irregular distribution of the strengthening precipitates has been revealed. In reference Alloy 625, the Nb-rich carbides and Laves phase precipitates exist in the interdendritic spaces. The TiB2 interacted with the liquid Alloy 625 during suction casting, leading to microstructural changes like more precipitates in interdendritic spaces including newly formed B-rich phases.
- Open Access
- 6 May 2025
- Published by Elsevier in Materials & Design
- Vol. 254
Microstructure, stability and oxidation resistance of ex-situ Alloy 625 + TiC nanocomposites processed by suction casting intended for repair of aerospace components
- 6 May 2025
- Published by Elsevier in Materials & Design
- Vol. 254
Open AccessMicrostructure, stability and oxidation resistance of ex-situ Alloy 625 + TiC nanocomposites processed by suction casting intended for repair of aerospace components