3D-Printed Demineralized Bone Matrix-Based Conductive Scaffolds Combined with Electrical Stimulation for Bone Tissue Engineering Applications
Open Access
- 21 June 2024
- journal article
- research article
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
- Vol. 7 (7) , 4366-4378
Abstract
Bone is remodeled through a dynamic process facilitated by biophysical cues that support cellular signaling. In healthy bone, signaling pathways are regulated by cells and the extracellular matrix and transmitted via electrical synapses. To this end, combining electrical stimulation (ES) with conductive scaffolding is a promising approach for repairing damaged bone tissue. Therefore, "smart" biomaterials that can provide multifunctionality and facilitate the transfer of electrical cues directly to cells have become increasingly more studied in bone tissue engineering. Herein, 3D-printed electrically conductive composite scaffolds consisting of demineralized bone matrix (DBM) and polycaprolactone (PCL), in combination with ES, for bone regeneration were evaluated for the first time. The conductive composite scaffolds were fabricated and characterized by evaluating mechanical, surface, and electrical properties. The DBM/PCL composites exhibited a higher compressive modulus (107.2 MPa) than that of pristine PCL (62.02 MPa), as well as improved surface properties (i.e., roughness). Scaffold electrical properties were also tuned, with sheet resistance values as low as 4.77 × 105 Ω/sq for our experimental coating of the highest dilution (i.e., 20%). Furthermore, the biocompatibility and osteogenic potential of the conductive composite scaffolds were tested using human mesenchymal stromal cells (hMSCs) both with and without exogenous ES (100 mV/mm for 5 min/day four times/week). In conjunction with ES, the osteogenic differentiation of hMSCs grown on conductive DBM/PCL composite scaffolds was significantly enhanced when compared to those cultured on PCL-only and nonconductive DBM/PCL control scaffolds, as determined through xylenol orange mineral staining and osteogenic protein analysis. Overall, these promising results suggest the potential of this approach for the development of biomimetic hybrid scaffolds for bone tissue engineering applications.Keywords
Funding Information
- MTF Biologics
This publication has 70 references indexed in Scilit:
- 3D‐Printed conductive polymeric scaffolds with direct current electrical stimulation for enhanced bone regenerationJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2023
- Three‐dimensionally printed polycaprolactone/beta‐tricalcium phosphate scaffold was more effective as an rhBMP‐2 carrier for new bone formation than polycaprolactone aloneJournal of Biomedical Materials Research Part A, 2020
- Smart MaterialsChemphyschem, 2018
- Development and Characterization of Organic Electronic Scaffolds for Bone Tissue EngineeringAdvanced Healthcare Materials, 2016
- Electrical Stimulation of Human Mesenchymal Stem Cells on Conductive Nanofibers Enhances their Differentiation toward Osteogenic OutcomesMacromolecular Rapid Communications, 2015
- Lithium‐end‐capped polylactide thin films influence osteoblast progenitor cell differentiation and mineralizationJournal of Biomedical Materials Research Part A, 2014
- In‐vivo behavior of Si‐hydroxyapatite/polycaprolactone/DMB scaffolds fabricated by 3D printingJournal of Biomedical Materials Research Part A, 2012
- Designed hybrid scaffolds consisting of polycaprolactone microstrands and electrospun collagen‐nanofibers for bone tissue regenerationJournal of Biomedical Materials Research Part B: Applied Biomaterials, 2011
- Electrical stimulation enhances viability of human cutaneous fibroblasts on conductive biodegradable substratesJournal of Biomedical Materials Research Part A, 2007
- Biological and Medical Significance of Calcium PhosphatesAngewandte Chemie International Edition, 2002