Dry etching characteristics of TiN film using Ar/CHF3, Ar/Cl2, and Ar/BCl3 gas chemistries in an inductively coupled plasma
Authors:
- 1 September 2003
- journal article
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 21 (5) , 2163-2168
Abstract
Dry etching characteristics of TiN film have been studied in the case of using Ar/CHF3, Ar/Cl2, and Ar/BCl3 chemistries in an inductively coupled plasma. The TiN film was not etched at all without the addition of CHF3, BCl3, or Cl2 to the Ar gas flow. On the other hand, it was found that the TiN film was etched with one of the earlier additional gases. It was also found that a nontapered profile of etched TiN is obtained by Cl2 addition and a tapered profile by CHF3 or BCl3 addition. Moreover, a lower taper angle is obtained by increasing the amount of additional BCl3. X-ray photoelectron spectroscopy and Auger electron spectroscopy analyses for the etched samples of TiN show that TiF3 exists on the etched surface of TiN in the case of CHF3 addition and that BOxNy exists in the case of BCl3 addition. On the basis of these results, the effect of the gas addition to Ar on the characteristics of TiN reactive ion etching is considered as follows; under the Ar/CHF3 condition, although N in the TiN film is removed by evaporation in the form of NFx, Ti is fluorinated to form TiFx having low vapor pressure, which results in the low etching rate. Under the Ar/Cl2 condition, since NClx and TiClx have high vapor pressures, TiN is easily etched off, resulting in the highest etching rate with a nontapered profile. Under the Ar/BCl3 condition, although Cl plays the same role as it does under the Ar/Cl2 condition, B is likely to form a nonvolatile compound such as BOxNy, resulting in the deposition of the nonvolatile films on both the upper surface and sidewall of the TiN, which leads to a lower etching rate than that in the case of Cl2 addition and a lower taper angle of the etched profile.Keywords
This publication has 12 references indexed in Scilit:
- A study of the failure mechanism of a titanium nitride diffusion barrierJournal of Applied Physics, 1999
- Characterization of Al, Cu, and TiN surface cleaning following a low-K dielectric etchJournal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena, 1999
- Performance of different etch chemistries on titanium nitride antireflective coating layers and related selectivity and microloading improvements for submicron geometries obtained with a high-density metal etcherJournal of Vacuum Science & Technology A, 1997
- Ashing residues on TiN antireflective coating layersJournal of Vacuum Science & Technology A, 1996
- Metal stack etching using a helical resonator plasmaJournal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena, 1996
- Notch Profile Defect in Aluminum Alloy Etching Using High-Density PlasmaJapanese Journal of Applied Physics, 1996
- Dry etching of titanium nitride thin films in CF4–O2 plasmasJournal of Vacuum Science & Technology A, 1995
- Electromigration in AlSiCu/TiN/Ti interconnects with Ti and TiN additional layersJournal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena, 1994
- Titanium mononitride as an antireflection layer on aluminium metallization for submicron photolithographic patterningSemiconductor Science and Technology, 1991
- Hybrid electron cyclotron resonance-RF plasma etching of TiNxthin films grown by low pressure rapid thermal metalorganic chemical vapour depositionSemiconductor Science and Technology, 1991