Hashem Khaled Almashaqbeh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hashem Khaled Almashaqbeh has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Alexander H. -D. Cheng
University of Mississippi
7 shared publications - Sasan Nouranian
University of Mississippi
5 shared publications - Chung R. Song
Department of Civil Engineering, University of Mississippi, Tupelo, MS, USA
4 shared publications Hunain Alkhateb
Center for Graphene Research and Innovation, University of Mississippi, Oxford, USA
4 shared publicationsDineshkumar Sengottuvelu
Center for Graphene Research and Innovation, University of Mississippi, Oxford, USA
3 shared publicationsGrace Rushing
Center for Graphene Research and Innovation, University of Mississippi, Oxford, USA
3 shared publications
Latest Publications
- Open Access
Tailoring Polyetherimide Ultrafiltration Membranes via Non-Solvent- and Vapor-Induced Phase Separation: Effects of Fabrication Pathway and Membrane Formulation on Morphology and Bovine Serum Albumin Separation Performance
Polyetherimide (PEI) ultrafiltration membranes were fabricated for bovine serum albumin (BSA) separation using nonsolvent-induced phase separation (NIPS) and vapor-induced phase separation (VIPS). In the NIPS approach, membranes containing varying amounts of Pluronic P-123, with or without graphene nanoplatelets (GNPs), were prepared. Pluronic P-123 acted as a pore-forming agent, while GNPs enhanced permeability without compromising rejection. The membrane with 1 wt.% Pluronic P-123 achieved a pure water flux (PWF) of 355 LMH and 90% BSA rejection. Incorporating 1 wt.% GNPs further improved performance to 747 LMH and 98% rejection. VIPS membranes were fabricated using the same composition as N10, containing 17 wt.% PEI and 1 wt.% Pluronic P-123 without GNPs, to isolate the effect of the fabrication pathway. Increasing vapor exposure time reduced PWF but generally improved BSA rejection, whereas higher RH increased PWF while decreasing rejection. The composition-matched NIPS membrane, N10, exhibited a PWF of 355 LMH and approximately 91% BSA rejection. In comparison, the highest PWF and BSA rejection among the VIPS membranes were 91 LMH and 76.5%, respectively, and the selected balanced VIPS condition at 30 min and 65% RH yielded approximately 49 LMH and 55% rejection. The higher performance of N11, which achieved 747 LMH and 98% rejection, is attributed to GNP incorporation within the NIPS series and was not used to isolate the fabrication-pathway effect. Overall, the composition-matched comparison demonstrates that NIPS produced a more favorable morphology and BSA separation performance than VIPS under the investigated conditions.
Open AccessTailoring Polyetherimide Ultrafiltration Membranes via Non-Solvent- and Vapor-Induced Phase Separation: Effects of Fabrication Pathway and Membrane Formulation on Morphology and Bovine Serum Albumin Separation Performance
Polyetherimide (PEI) ultrafiltration membranes were fabricated for bovine serum albumin (BSA) separation using nonsolvent-induced phase separation (NIPS) and vapor-induced phase separation (VIPS). In the NIPS approach, membranes containing varying amounts of Pluronic P-123, with or without graphene nanoplatelets (GNPs), were prepared. Pluronic P-123 acted as a pore-forming agent, while GNPs enhanced permeability without compromising rejection. The membrane with 1 wt.% Pluronic P-123 achieved a pure water flux (PWF) of 355 LMH and 90% BSA rejection. Incorporating 1 wt.% GNPs further improved performance to 747 LMH and 98% rejection. VIPS membranes were fabricated using the same composition as N10, containing 17 wt.% PEI and 1 wt.% Pluronic P-123 without GNPs, to isolate the effect of the fabrication pathway. Increasing vapor exposure time reduced PWF but generally improved BSA rejection, whereas higher RH increased PWF while decreasing rejection. The composition-matched NIPS membrane, N10, exhibited a PWF of 355 LMH and approximately 91% BSA rejection. In comparison, the highest PWF and BSA rejection among the VIPS membranes were 91 LMH and 76.5%, respectively, and the selected balanced VIPS condition at 30 min and 65% RH yielded approximately 49 LMH and 55% rejection. The higher performance of N11, which achieved 747 LMH and 98% rejection, is attributed to GNP incorporation within the NIPS series and was not used to isolate the fabrication-pathway effect. Overall, the composition-matched comparison demonstrates that NIPS produced a more favorable morphology and BSA separation performance than VIPS under the investigated conditions.
- 16 July 2026
- Published by Emerald Publishing in The TQM Journal
- p. 1-21
A quality governance framework for project-based construction using interpretable machine learning
Purpose: This study reconceptualizes quality management in project-based construction as a governance mechanism rather than a reactive inspection function. It shows how interpretable Machine Learning (ML) can operationalize TQM into transparent quality gates regulating cost escalation, project risk and audit attention under construction data constraints. Design/methodology/approach: A staged mixed-methods design was used. Practitioner interviews and expert consensus defined governance-critical variables, which were embedded into a synthetic dataset for simulation-based internal evaluation. Multiple linear regression, logistic regression and Isolation Forest models represented rework-cost signaling, risk escalation, and anomaly-based audit functions. Robustness testing and a two-round Delphi study assessed structural coherence and practical relevance. Findings: The framework showed strong internal coherence. Rework-cost estimation explained substantial cost exposure (R2 = 0.8156), identifying training coverage and defect accumulation as dominant governance levers. Risk classification achieved high discrimination (AUC = 0.9425), and anomaly detection identified unusual projects for targeted review and learning. The framework provides a structured, interpretable decision-support architecture for quality planning and escalation control. Practical implications: Once calibrated with project-level quality data, the framework can convert fragmented quality records into governance signals for prioritizing quality investment, escalating high-risk projects and targeting audits before quality failures become costly. Originality/value: Rather than proposing new algorithms, this study contributes a simulation-evaluated decision-rule architecture linking rework-cost signaling, risk escalation gates and anomaly-triggered audit learning within one governance workflow, advancing Quality 4.0 toward interpretable, governance-compatible decision support.
- 16 July 2026
- Published by Emerald Publishing in The TQM Journal
- p. 1-21
A quality governance framework for project-based construction using interpretable machine learning
Purpose: This study reconceptualizes quality management in project-based construction as a governance mechanism rather than a reactive inspection function. It shows how interpretable Machine Learning (ML) can operationalize TQM into transparent quality gates regulating cost escalation, project risk and audit attention under construction data constraints. Design/methodology/approach: A staged mixed-methods design was used. Practitioner interviews and expert consensus defined governance-critical variables, which were embedded into a synthetic dataset for simulation-based internal evaluation. Multiple linear regression, logistic regression and Isolation Forest models represented rework-cost signaling, risk escalation, and anomaly-based audit functions. Robustness testing and a two-round Delphi study assessed structural coherence and practical relevance. Findings: The framework showed strong internal coherence. Rework-cost estimation explained substantial cost exposure (R2 = 0.8156), identifying training coverage and defect accumulation as dominant governance levers. Risk classification achieved high discrimination (AUC = 0.9425), and anomaly detection identified unusual projects for targeted review and learning. The framework provides a structured, interpretable decision-support architecture for quality planning and escalation control. Practical implications: Once calibrated with project-level quality data, the framework can convert fragmented quality records into governance signals for prioritizing quality investment, escalating high-risk projects and targeting audits before quality failures become costly. Originality/value: Rather than proposing new algorithms, this study contributes a simulation-evaluated decision-rule architecture linking rework-cost signaling, risk escalation gates and anomaly-triggered audit learning within one governance workflow, advancing Quality 4.0 toward interpretable, governance-compatible decision support.
- Open Access
- 1 August 2025
- Published by MDPI AG in Chemengineering
- Vol. 9 (4) , 83
Molecular Dynamics Simulation of PFAS Adsorption on Graphene for Enhanced Water Purification
The contamination of drinking water by per- and polyfluoroalkyl substances (PFASs) presents a global concern due to their extreme persistence, driven by strong C–F bonds. This study investigated the potential of graphene as a filtration material for PFAS removal, focusing on six key compounds regulated by the U.S. EPA: PFOA, PFNA, GenX, PFBS, PFOS, and PFHxS. Using molecular simulations, adsorption energy, diffusion coefficients, and PFAS-to-graphene distances were analyzed. The results showed that adsorption strength increased with molecular weight; PFOS (500 g/mol) exhibited the strongest adsorption (−171 kcal/mol). Compounds with sulfonic acid head groups (e.g., PFOS) had stronger interactions than those with carboxylate groups (e.g., PFNA), highlighting the importance of head group chemistry. Shorter graphene-to-PFAS distances also aligned with higher adsorption energies. PFOS, for example, had the shortest distance at 8.23 Å (head) and 6.15 Å (tail) from graphene. Diffusion coefficients decreased with increasing molecular weight and carbon chain length, with lower molecules like PFBS (four carbon atoms) diffusing more rapidly than heavier ones like PFOS and PFNA. Interestingly, graphene enhanced PFAS mobility in water, likely by disrupting the water structure and lowering intermolecular resistance. These results highlight graphene’s promise as a high-performance material for PFAS removal and future water purification technologies.
- 1 August 2025
- Published by MDPI AG in Chemengineering
- Vol. 9 (4) , 83
Open AccessMolecular Dynamics Simulation of PFAS Adsorption on Graphene for Enhanced Water Purification
The contamination of drinking water by per- and polyfluoroalkyl substances (PFASs) presents a global concern due to their extreme persistence, driven by strong C–F bonds. This study investigated the potential of graphene as a filtration material for PFAS removal, focusing on six key compounds regulated by the U.S. EPA: PFOA, PFNA, GenX, PFBS, PFOS, and PFHxS. Using molecular simulations, adsorption energy, diffusion coefficients, and PFAS-to-graphene distances were analyzed. The results showed that adsorption strength increased with molecular weight; PFOS (500 g/mol) exhibited the strongest adsorption (−171 kcal/mol). Compounds with sulfonic acid head groups (e.g., PFOS) had stronger interactions than those with carboxylate groups (e.g., PFNA), highlighting the importance of head group chemistry. Shorter graphene-to-PFAS distances also aligned with higher adsorption energies. PFOS, for example, had the shortest distance at 8.23 Å (head) and 6.15 Å (tail) from graphene. Diffusion coefficients decreased with increasing molecular weight and carbon chain length, with lower molecules like PFBS (four carbon atoms) diffusing more rapidly than heavier ones like PFOS and PFNA. Interestingly, graphene enhanced PFAS mobility in water, likely by disrupting the water structure and lowering intermolecular resistance. These results highlight graphene’s promise as a high-performance material for PFAS removal and future water purification technologies.
- Open Access
- 24 June 2025
- Published by MDPI AG in Infrastructures
- Vol. 10 (7) , 153
Comparative Study of Machine Learning Techniques for Predicting UCS Values Using Basic Soil Index Parameters in Pavement Construction
This study investigated the prediction of unconfined compressive strength (UCS), a common measure of soil’s undrained shear strength, using fundamental soil characteristics. While traditional pavement subgrade design often relies on parameters like the resilient modulus and California bearing ratio (CBR), researchers are exploring the potential of incorporating more easily obtainable strength indicators, such as UCS. To evaluate the potential effectiveness of UCS for pavement engineering applications, a dataset of 152 laboratory-tested soil samples was compiled to develop predictive models. For each sample, geotechnical properties including the Atterberg limits, liquid limit (LL), plastic limit (PL), water content (WC), and bulk density (determined using the Harvard miniature compaction apparatus), alongside the UCS, were measured. This dataset served to train various models to estimate the UCS from basic soil parameters. The methods employed included multi-linear regression (MLR), multi-nonlinear regression (MNLR), and several machine learning techniques: backpropagation artificial neural networks (ANNs), gradient boosting (GB), random forest (RF), support vector machine (SVM), and K-nearest neighbor (KNN). The aim was to establish a relationship between the dependent variable (UCS) and the independent basic geotechnical properties and to test the effectiveness of each ML algorithm in predicting UCS. The results indicate that the ANN-based model provided the most accurate predictions for UCS, achieving an R2 of 0.83, a root-mean-squared error (RMSE) of 1.11, and a mean absolute relative error (MARE) of 0.42. The performance ranking of the other models, from best to worst, was RF, GB, SV, KNN, MLR, and MNLR.
- 24 June 2025
- Published by MDPI AG in Infrastructures
- Vol. 10 (7) , 153
Open AccessComparative Study of Machine Learning Techniques for Predicting UCS Values Using Basic Soil Index Parameters in Pavement Construction
This study investigated the prediction of unconfined compressive strength (UCS), a common measure of soil’s undrained shear strength, using fundamental soil characteristics. While traditional pavement subgrade design often relies on parameters like the resilient modulus and California bearing ratio (CBR), researchers are exploring the potential of incorporating more easily obtainable strength indicators, such as UCS. To evaluate the potential effectiveness of UCS for pavement engineering applications, a dataset of 152 laboratory-tested soil samples was compiled to develop predictive models. For each sample, geotechnical properties including the Atterberg limits, liquid limit (LL), plastic limit (PL), water content (WC), and bulk density (determined using the Harvard miniature compaction apparatus), alongside the UCS, were measured. This dataset served to train various models to estimate the UCS from basic soil parameters. The methods employed included multi-linear regression (MLR), multi-nonlinear regression (MNLR), and several machine learning techniques: backpropagation artificial neural networks (ANNs), gradient boosting (GB), random forest (RF), support vector machine (SVM), and K-nearest neighbor (KNN). The aim was to establish a relationship between the dependent variable (UCS) and the independent basic geotechnical properties and to test the effectiveness of each ML algorithm in predicting UCS. The results indicate that the ANN-based model provided the most accurate predictions for UCS, achieving an R2 of 0.83, a root-mean-squared error (RMSE) of 1.11, and a mean absolute relative error (MARE) of 0.42. The performance ranking of the other models, from best to worst, was RF, GB, SV, KNN, MLR, and MNLR.
- Open Access
FIMOFs: Fiber-Integrated Metal–Organic Frameworks Through Electrospinning
Green synthesis plays a crucial role in advancing sustainability within materials science. This study explores the integration of metal–organic frameworks (MOFs), obtained through green synthesis, using an electrospinning post-processing technique to develop MOF-based composite materials. The resulting novel multifunctional composites demonstrate enhanced stability and functionality, compared to their control counterparts. The integration of four types of MOFs into an electrospun fiber network was investigated using a specific polymer solution. Characterization and preliminary adsorption studies were conducted to elucidate the chemistry, morphology, and adsorptive capabilities of the resulting MOF composites. Electrospinning MOFs into polymer fibers improved their stability and dye removal capabilities. More specifically, optimization of MOF-to-polymer ratios and processing conditions yielded composites that are thermally stable, with modified surface area and porosity. Post-processing MOFs resulted in a fiber diameter increase of 44 and 109%, enhancing the composites by providing more MOF active sites and improved mechanical strength. Zirconium-based post-processed MOFs demonstrated superior dye removal, different from the copper-based dyes. Electrospinning technology has demonstrated significant potential in the fabrication of high-performance multifunctional MOF composites. This has helped to create advanced sustainable composites with tailored properties, paving the way for more targeted and efficient applications. The applications of these composites show promise for military engineering where durable, light weight, and multifunctional materials are critical in contributing to improved performance, operational efficiency, and safety.
Open AccessFIMOFs: Fiber-Integrated Metal–Organic Frameworks Through Electrospinning
Green synthesis plays a crucial role in advancing sustainability within materials science. This study explores the integration of metal–organic frameworks (MOFs), obtained through green synthesis, using an electrospinning post-processing technique to develop MOF-based composite materials. The resulting novel multifunctional composites demonstrate enhanced stability and functionality, compared to their control counterparts. The integration of four types of MOFs into an electrospun fiber network was investigated using a specific polymer solution. Characterization and preliminary adsorption studies were conducted to elucidate the chemistry, morphology, and adsorptive capabilities of the resulting MOF composites. Electrospinning MOFs into polymer fibers improved their stability and dye removal capabilities. More specifically, optimization of MOF-to-polymer ratios and processing conditions yielded composites that are thermally stable, with modified surface area and porosity. Post-processing MOFs resulted in a fiber diameter increase of 44 and 109%, enhancing the composites by providing more MOF active sites and improved mechanical strength. Zirconium-based post-processed MOFs demonstrated superior dye removal, different from the copper-based dyes. Electrospinning technology has demonstrated significant potential in the fabrication of high-performance multifunctional MOF composites. This has helped to create advanced sustainable composites with tailored properties, paving the way for more targeted and efficient applications. The applications of these composites show promise for military engineering where durable, light weight, and multifunctional materials are critical in contributing to improved performance, operational efficiency, and safety.
- Open Access
- 20 January 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (1) , 1-21
Efficacy of octadecylamine-functionalized graphene versus graphene nanoplatelets and graphene oxide as asphalt binder modifiers for high-temperature performance
In this work, we comprehensively report on the synthesis of octadecylamine (ODA)-functionalized graphene (G-ODA) and compare its performance to those of graphene nanoplatelets (GNPs) and graphene oxide (GO) as asphalt binder modifiers. An exploration into the mechanisms through which asphalt binder properties are enhanced by each graphene-based material has been conducted, identifying the one that demonstrates superior compatibility with asphalt. The study systematically evaluates the performance of each modifier, analyzing viscosity, rheology, anti-aging properties, morphology, and chemical transformations within asphalt binders. Experimental results indicate that all three graphene-based modifiers enhance the high-temperature performance and aging resistance of the asphalt binder, with GO emerging as the most compatible material, exhibiting superior performance across all investigated responses. The rheological properties results show that GO can improve G*/sin(δ) for the unaged binder by about 120%, followed by G-ODA and GNP. On the contrary, multiple stress creep and recovery (MSCR) results indicate that both GO and GNP efficiently reduce permanent deformation, with reductions in Jnr of about 39% and 34%, respectively while the G-ODA shows a smaller reduction of − 10%. Additionally, GO excels in improving elastic response, showing a substantial increase in percent recovery at 297%, compared to 48.4% with GNP and 28.8% with G-ODA. Fourier-transform infrared spectroscopy (FTIR) analysis establishes the absence of evidence indicating chemical interaction between any of the graphene-based materials and asphalt molecules. This suggests that the improvement is solely attributed to physical interaction, specifically through π-π interaction. On the other hand, AFM phase images indicate that all graphene-based materials can alter the morphology of asphalt binders. They increase the projected surface area of the Peri/Catana phases, which can influence the rheological properties of the binder.
- 20 January 2025
- Published by Springer Nature in Materials and Structures
- Vol. 58 (1) , 1-21
Open AccessEfficacy of octadecylamine-functionalized graphene versus graphene nanoplatelets and graphene oxide as asphalt binder modifiers for high-temperature performance
In this work, we comprehensively report on the synthesis of octadecylamine (ODA)-functionalized graphene (G-ODA) and compare its performance to those of graphene nanoplatelets (GNPs) and graphene oxide (GO) as asphalt binder modifiers. An exploration into the mechanisms through which asphalt binder properties are enhanced by each graphene-based material has been conducted, identifying the one that demonstrates superior compatibility with asphalt. The study systematically evaluates the performance of each modifier, analyzing viscosity, rheology, anti-aging properties, morphology, and chemical transformations within asphalt binders. Experimental results indicate that all three graphene-based modifiers enhance the high-temperature performance and aging resistance of the asphalt binder, with GO emerging as the most compatible material, exhibiting superior performance across all investigated responses. The rheological properties results show that GO can improve G*/sin(δ) for the unaged binder by about 120%, followed by G-ODA and GNP. On the contrary, multiple stress creep and recovery (MSCR) results indicate that both GO and GNP efficiently reduce permanent deformation, with reductions in Jnr of about 39% and 34%, respectively while the G-ODA shows a smaller reduction of − 10%. Additionally, GO excels in improving elastic response, showing a substantial increase in percent recovery at 297%, compared to 48.4% with GNP and 28.8% with G-ODA. Fourier-transform infrared spectroscopy (FTIR) analysis establishes the absence of evidence indicating chemical interaction between any of the graphene-based materials and asphalt molecules. This suggests that the improvement is solely attributed to physical interaction, specifically through π-π interaction. On the other hand, AFM phase images indicate that all graphene-based materials can alter the morphology of asphalt binders. They increase the projected surface area of the Peri/Catana phases, which can influence the rheological properties of the binder.
- Open Access
- 23 April 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (5) , 159
Simulation of the Dynamic Responses of Layered Polymer Composites under Plate Impact Using the DSGZ Model
This paper presents a numerical study on the dynamic response and impact mitigation capabilities of layered ceramic–polymer–metal (CPM) composites under plate impact loading, focusing on the layer sequence effect. The layered structure, comprising a ceramic for hardness and thermal resistance, a polymer for energy absorption, and a metal for strength and ductility, is analyzed to evaluate its effectiveness in mitigating the impact loading. The simulations employed the VUMAT subroutine of DSGZ material models within Abaqus/Explicit to accurately represent the mechanical behavior of the polymeric materials in the composites. The VUMAT implementation incorporates the explicit time integration scheme and the implicit radial return mapping algorithm. A safe-version Newton–Raphson method is applied for numerically solving the differential equations of the plastic flow theory. Analysis of the simulation results reveals that specific layer configurations significantly influence wave propagation, leading to variations in energy absorption and stress distribution within the material. Notably, certain layer sequences, such as P-C-M and C-P-M, exhibit enhanced impact mitigation with a superior ability to dissipate and redirect the impact energy. This phenomenon is tied to the interactions between the material properties of the ceramic, polymer, and metal, emphasizing the necessity of precise material characterization and enhanced understanding of the layer sequencing effect for optimizing composite designs for impact mitigation. The integration of empirical data with simulation methods provides a comprehensive framework for optimizing composite designs in high-impact scenarios. In the general fields of materials science and impact engineering, the current research offers some guidance for practical applications, underscoring the need for detailed simulations to capture the high-strain-rate dynamic responses of multilayered composites.- 23 April 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (5) , 159
Open AccessSimulation of the Dynamic Responses of Layered Polymer Composites under Plate Impact Using the DSGZ Model
This paper presents a numerical study on the dynamic response and impact mitigation capabilities of layered ceramic–polymer–metal (CPM) composites under plate impact loading, focusing on the layer sequence effect. The layered structure, comprising a ceramic for hardness and thermal resistance, a polymer for energy absorption, and a metal for strength and ductility, is analyzed to evaluate its effectiveness in mitigating the impact loading. The simulations employed the VUMAT subroutine of DSGZ material models within Abaqus/Explicit to accurately represent the mechanical behavior of the polymeric materials in the composites. The VUMAT implementation incorporates the explicit time integration scheme and the implicit radial return mapping algorithm. A safe-version Newton–Raphson method is applied for numerically solving the differential equations of the plastic flow theory. Analysis of the simulation results reveals that specific layer configurations significantly influence wave propagation, leading to variations in energy absorption and stress distribution within the material. Notably, certain layer sequences, such as P-C-M and C-P-M, exhibit enhanced impact mitigation with a superior ability to dissipate and redirect the impact energy. This phenomenon is tied to the interactions between the material properties of the ceramic, polymer, and metal, emphasizing the necessity of precise material characterization and enhanced understanding of the layer sequencing effect for optimizing composite designs for impact mitigation. The integration of empirical data with simulation methods provides a comprehensive framework for optimizing composite designs in high-impact scenarios. In the general fields of materials science and impact engineering, the current research offers some guidance for practical applications, underscoring the need for detailed simulations to capture the high-strain-rate dynamic responses of multilayered composites. - Open Access
- 13 April 2024
- Published by Springer Nature in Materials and Structures
- Vol. 57 (4) , 1-15
Effects of the geometric characteristics of graphene nanoplatelets on the physico-rheological properties of asphalt binder
While graphene nanoplatelets (GnPs) have emerged as promising nano-modifiers of asphalt binder in recent years, much is still unknown in terms of the existing correlations between the physical, chemical, and geometric characteristics of this nanofiller and observed asphalt binder properties. In this work, we investigate the important correlation between the geometric characteristics of GnPs and the rheological properties of the GnP-modified asphalt binder at high temperatures. Our results indicate that, in general, incorporating GnPs with large mean particle diameters (> 14 μm) and thicknesses (> 8 nm) enhances the high-temperature performance of the asphalt binder. The results of the multiple stress creep and recovery tests confirm that including GnPs in asphalt binder can decrease its permanent deformation by 33.2% and enhance its elastic recovery by 53.9%. Phase contrast images obtained by atomic force microscopy further indicate that the presence of GnPs with large mean particle diameters alters the morphology of the asphalt binder, leading to improved temperature stability and less susceptibility to permanent deformation.
- 13 April 2024
- Published by Springer Nature in Materials and Structures
- Vol. 57 (4) , 1-15
Open AccessEffects of the geometric characteristics of graphene nanoplatelets on the physico-rheological properties of asphalt binder
While graphene nanoplatelets (GnPs) have emerged as promising nano-modifiers of asphalt binder in recent years, much is still unknown in terms of the existing correlations between the physical, chemical, and geometric characteristics of this nanofiller and observed asphalt binder properties. In this work, we investigate the important correlation between the geometric characteristics of GnPs and the rheological properties of the GnP-modified asphalt binder at high temperatures. Our results indicate that, in general, incorporating GnPs with large mean particle diameters (> 14 μm) and thicknesses (> 8 nm) enhances the high-temperature performance of the asphalt binder. The results of the multiple stress creep and recovery tests confirm that including GnPs in asphalt binder can decrease its permanent deformation by 33.2% and enhance its elastic recovery by 53.9%. Phase contrast images obtained by atomic force microscopy further indicate that the presence of GnPs with large mean particle diameters alters the morphology of the asphalt binder, leading to improved temperature stability and less susceptibility to permanent deformation.
- Open Access
- 20 December 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Effects of Surface Area and Particle Size of Graphite and Graphene Nanoplatelets on Their Oxidation and Subsequent Use in the Modification of Asphalt Binder
Graphene oxide (GO) has gained significant attention for its unique physical and chemical properties. GO finds application in a wide range of fields, including biomedicine, electronics, energy, and the environment. It also plays a significant role in the modification of infrastructure materials, such as asphalt and cement, in civil engineering. In this study, we report on the synthesis of GOs from graphite (Gr) powder and graphene nanoplatelets (GNPs) using an improved Hummers’ method. We extensively investigated the effects of particle size and specific surface area of the Gr and GNP precursors on their oxidation, which have not been addressed in literature. The results from Fourier-transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses show that the GO made from Gr powder with a large surface area and small size has a higher degree of oxidation with about 9.8% carboxyl functional groups. This provides more opportunities for interactions with different molecules, including asphalt components. In this regard, we investigated the impact of carboxyl-rich GO (higher oxidation percentage) on the high-temperature performance of asphalt binder through rotational viscosity, rheology, multiple stress creep and recovery (MSCR), and anti-aging property measurements. Our experimental results indicate that GO obtained from the Gr powder precursor (designated ox-Gr) can significantly improve the high-temperature performance of asphalt binder. For example, the introduction of only 2 wt.% GO to a performance grade asphalt binder (PG 67-22) can dramatically increase its complex shear modulus (G*), as well as decrease the phase angle (δ), at high temperatures. The MSCR tests showed that the addition of GO to asphalt binder effectively mitigates its permanent deformation and improves its elastic response, as demonstrated by about 39% reduction in the creep compliance (J_nr) and an impressive 297% increase in the percent recovery (εR) of the GO-modified binder. Furthermore, the measured viscosity aging index and G* ratio of the GO-modified asphalt binder confirm the significant effect of GO on the improvement of the anti-aging properties of the binder.
- 20 December 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessEffects of Surface Area and Particle Size of Graphite and Graphene Nanoplatelets on Their Oxidation and Subsequent Use in the Modification of Asphalt Binder
Graphene oxide (GO) has gained significant attention for its unique physical and chemical properties. GO finds application in a wide range of fields, including biomedicine, electronics, energy, and the environment. It also plays a significant role in the modification of infrastructure materials, such as asphalt and cement, in civil engineering. In this study, we report on the synthesis of GOs from graphite (Gr) powder and graphene nanoplatelets (GNPs) using an improved Hummers’ method. We extensively investigated the effects of particle size and specific surface area of the Gr and GNP precursors on their oxidation, which have not been addressed in literature. The results from Fourier-transform infrared (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses show that the GO made from Gr powder with a large surface area and small size has a higher degree of oxidation with about 9.8% carboxyl functional groups. This provides more opportunities for interactions with different molecules, including asphalt components. In this regard, we investigated the impact of carboxyl-rich GO (higher oxidation percentage) on the high-temperature performance of asphalt binder through rotational viscosity, rheology, multiple stress creep and recovery (MSCR), and anti-aging property measurements. Our experimental results indicate that GO obtained from the Gr powder precursor (designated ox-Gr) can significantly improve the high-temperature performance of asphalt binder. For example, the introduction of only 2 wt.% GO to a performance grade asphalt binder (PG 67-22) can dramatically increase its complex shear modulus (G*), as well as decrease the phase angle (δ), at high temperatures. The MSCR tests showed that the addition of GO to asphalt binder effectively mitigates its permanent deformation and improves its elastic response, as demonstrated by about 39% reduction in the creep compliance (J_nr) and an impressive 297% increase in the percent recovery (εR) of the GO-modified binder. Furthermore, the measured viscosity aging index and G* ratio of the GO-modified asphalt binder confirm the significant effect of GO on the improvement of the anti-aging properties of the binder.
- Open Access
- 8 September 2023
- Published by Springer Nature in Research Square
Effects of the Geometric Characteristics of Graphene Nanoplatelets on the Physico-Rheological Properties of Asphalt Binder
While graphene nanoplatelets (GnPs) have emerged as promising nano-modifiers of asphalt binder in recent years, much is still unknown in terms of the existing correlations between the physical, chemical, and geometric characteristics of this nanofiller and observed asphalt binder properties. In this work, we investigate the important correlation between the geometric characteristics of GnPs and the rheological properties of the GnP-modified asphalt binder at high temperatures. Our results indicate that, in general, incorporating GnPs with large mean particle diameters (> 14 µm) and thicknesses (> 8 nm) enhances the high-temperature performance of the asphalt binder. The results of the multiple stress creep and recovery tests confirm that including GnPs in asphalt binder can decrease its permanent deformation by 33.2% and enhance its elastic recovery by 53.9%. Phase images obtained by atomic force microscopy further indicate that the presence of GnPs with large mean particle diameters alters the morphology of the asphalt binder, leading to improved temperature stability and less susceptibility to permanent deformation.
- 8 September 2023
- Published by Springer Nature in Research Square
Open AccessEffects of the Geometric Characteristics of Graphene Nanoplatelets on the Physico-Rheological Properties of Asphalt Binder
While graphene nanoplatelets (GnPs) have emerged as promising nano-modifiers of asphalt binder in recent years, much is still unknown in terms of the existing correlations between the physical, chemical, and geometric characteristics of this nanofiller and observed asphalt binder properties. In this work, we investigate the important correlation between the geometric characteristics of GnPs and the rheological properties of the GnP-modified asphalt binder at high temperatures. Our results indicate that, in general, incorporating GnPs with large mean particle diameters (> 14 µm) and thicknesses (> 8 nm) enhances the high-temperature performance of the asphalt binder. The results of the multiple stress creep and recovery tests confirm that including GnPs in asphalt binder can decrease its permanent deformation by 33.2% and enhance its elastic recovery by 53.9%. Phase images obtained by atomic force microscopy further indicate that the presence of GnPs with large mean particle diameters alters the morphology of the asphalt binder, leading to improved temperature stability and less susceptibility to permanent deformation.