Chung R. Song
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Chung R. Song has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- George Z. Voyiadjis
Louisiana State Univ
7 shared publications - Alexander H. -D. Cheng
University of Mississippi
6 shared publications - Hashem Khaled Almashaqbeh
Center for Graphene Research and Innovation, University of Mississippi, Oxford, MS 38677, USA
4 shared publications - Jinwon Kim
Associated Professor, Dept. of Civil Engineering, Univ. of Mississippi, Carrier 218, University, MS 38677.
3 shared publications - Sudarshan Adhikari
Fugro Marine GeoServices Inc., Houston, TX, USA
2 shared publications Ahmed Alostaz
1 shared publication
Latest Publications
- 17 May 2016
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 10 (5) , 419-427
Self-sealing bentonite strip: an effective method to prevent gap development for floodwalls in New Orleans
Many sections of floodwalls in New Orleans, LA were damaged or suffered catastrophic failure as a result of Hurricane Katrina. One of the key triggering mechanisms of failure reported is the gap development between the floodwall and soil. This study developed an effective retrofitting technique to prevent this gap development by introducing a buried layer of self-sealing sand and bentonite mixture. This self-sealing layer was expected to swell fast enough so that it could seal the gap without any time delay and to exert insignificant swelling pressure to the levee so that it did not affect the stability of the levee. Among several mixtures of sand and bentonite, the mixture of 70% sand and 30% bentonite (by dry weight) proved to be a more effective one among laboratory and large scale model tests conducted in this study by swelling fast enough to seal the gap (approximately 10% swelling strain in 2 days), but exerting insignificant swelling pressure (162.03 kPa in 2 days) to the levee. From the numerical analysis using FLAC3D, it was confirmed that the stability of the levee was actually increased by sealing the gap even with the minor swelling pressure from the self-sealing layer. From 1/64th scale centrifuge tests, the wall with the self-sealing layer did not fail at 64 g, while the one without the self-sealing layer failed at 25 g acceleration.
- 17 May 2016
- Published by Taylor & Francis in International Journal of Geotechnical Engineering
- Vol. 10 (5) , 419-427
Self-sealing bentonite strip: an effective method to prevent gap development for floodwalls in New Orleans
Many sections of floodwalls in New Orleans, LA were damaged or suffered catastrophic failure as a result of Hurricane Katrina. One of the key triggering mechanisms of failure reported is the gap development between the floodwall and soil. This study developed an effective retrofitting technique to prevent this gap development by introducing a buried layer of self-sealing sand and bentonite mixture. This self-sealing layer was expected to swell fast enough so that it could seal the gap without any time delay and to exert insignificant swelling pressure to the levee so that it did not affect the stability of the levee. Among several mixtures of sand and bentonite, the mixture of 70% sand and 30% bentonite (by dry weight) proved to be a more effective one among laboratory and large scale model tests conducted in this study by swelling fast enough to seal the gap (approximately 10% swelling strain in 2 days), but exerting insignificant swelling pressure (162.03 kPa in 2 days) to the levee. From the numerical analysis using FLAC3D, it was confirmed that the stability of the levee was actually increased by sealing the gap even with the minor swelling pressure from the self-sealing layer. From 1/64th scale centrifuge tests, the wall with the self-sealing layer did not fail at 64 g, while the one without the self-sealing layer failed at 25 g acceleration.
- 4 January 2015
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 33 (4) , 325-336
Anisotropic Analysis of I-Walls in New Orleans
Many numerical analyses of New Orleans levee and floodwall sections adopted mostly isotropic soil models partly due to the inherent simplicity of isotropic models. However, the isotropic models may not be sufficient to properly address the anisotropic behavior of soils. To overcome this imperfection, this study incorporated an anisotropic Modified Cam Clay model in a commercially available finite difference code, FLAC3D, and analyzed a floodwall and levee section in the 17th St. Canal in New Orleans. The analysis showed that the anisotropic model resulted in a similar overall deformation to the Mohr-Coulomb isotropic model. However, the anisotropic model showed more widely spread yielded elements and higher shear strain gradient in the Lacustrine clay layer, reconfirming that the Lacustrine clay layer played a major role for the failure in the 17th St. Canal. This result also signified that the isotropic Mohr-Coulomb model might be good for evaluating overall behavior in moderate deformation problems, while the anisotropic Modified Cam Clay model was good even for large strain problems where more accurate evaluation of yielding is needed.
- 4 January 2015
- Published by Taylor & Francis in Marine Georesources & Geotechnology
- Vol. 33 (4) , 325-336
Anisotropic Analysis of I-Walls in New Orleans
Many numerical analyses of New Orleans levee and floodwall sections adopted mostly isotropic soil models partly due to the inherent simplicity of isotropic models. However, the isotropic models may not be sufficient to properly address the anisotropic behavior of soils. To overcome this imperfection, this study incorporated an anisotropic Modified Cam Clay model in a commercially available finite difference code, FLAC3D, and analyzed a floodwall and levee section in the 17th St. Canal in New Orleans. The analysis showed that the anisotropic model resulted in a similar overall deformation to the Mohr-Coulomb isotropic model. However, the anisotropic model showed more widely spread yielded elements and higher shear strain gradient in the Lacustrine clay layer, reconfirming that the Lacustrine clay layer played a major role for the failure in the 17th St. Canal. This result also signified that the isotropic Mohr-Coulomb model might be good for evaluating overall behavior in moderate deformation problems, while the anisotropic Modified Cam Clay model was good even for large strain problems where more accurate evaluation of yielding is needed.
- 4 September 2013
- Published by Springer Nature in Acta Geotechnica
- Vol. 9 (6) , 1123-1134
Evaluation of I-wall in New Orleans with back-calculated total stress soil parameters
- 4 September 2013
- Published by Springer Nature in Acta Geotechnica
- Vol. 9 (6) , 1123-1134
Evaluation of I-wall in New Orleans with back-calculated total stress soil parameters
- 18 June 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 1688-1694
Expansive Clay Minerals and Hurricane Katrina
In 2005, Hurricane Katrina landed on the southern states of the U.S. and caused more than 1000 deaths and severe property damage. The life loss and property damage were mostly caused by the failure of floodwalls that surrounded City of New Orleans. Several cases of failures were caused by so called "gap formation" and "erosion" which were believed to be due to the dispersive characteristics of expansive clay minerals contained in levee soils. The New Orleans area has wide distribution of expansive clay minerals. Some soils in this area contained as high as 5% montmorillonite soils. In this study, it turned out that the undrained shear strength and erosion resistance of these soils can drop as low as immeasurable range when wet. This paper experimentally and analytically addresses the behavior of expansive soils contained in levee soils that triggered the failure of the levees under heavy rain and overtopping condition.
- 18 June 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 1688-1694
Expansive Clay Minerals and Hurricane Katrina
In 2005, Hurricane Katrina landed on the southern states of the U.S. and caused more than 1000 deaths and severe property damage. The life loss and property damage were mostly caused by the failure of floodwalls that surrounded City of New Orleans. Several cases of failures were caused by so called "gap formation" and "erosion" which were believed to be due to the dispersive characteristics of expansive clay minerals contained in levee soils. The New Orleans area has wide distribution of expansive clay minerals. Some soils in this area contained as high as 5% montmorillonite soils. In this study, it turned out that the undrained shear strength and erosion resistance of these soils can drop as low as immeasurable range when wet. This paper experimentally and analytically addresses the behavior of expansive soils contained in levee soils that triggered the failure of the levees under heavy rain and overtopping condition.
- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (10) , 874-881
Reducing Erosion of Earthen Levees Using Engineered Flood Wall Surface
Erosion was one of the major causes for the failure of New Orleans levee system during Hurricane Katrina. Protection of flood walls from erosion failure can be achieved in many different ways. This study consisted of experimental research to develop engineered flood wall surfaces that can reduce the erosion energy of the plunging water before the water hits the levee surface, so that the flood protection system becomes more resilient. Test results were compared to hydrodynamics simulation results by using FLOW3D. The results revealed that the erosion resistance of levees can be substantially reduced by providing protective structures at the surface of the flood walls. An effectively designed protective structure could reduce the erosion depth as much as 40% and extend the erosion time as much as 400%.
- 1 October 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (10) , 874-881
Reducing Erosion of Earthen Levees Using Engineered Flood Wall Surface
Erosion was one of the major causes for the failure of New Orleans levee system during Hurricane Katrina. Protection of flood walls from erosion failure can be achieved in many different ways. This study consisted of experimental research to develop engineered flood wall surfaces that can reduce the erosion energy of the plunging water before the water hits the levee surface, so that the flood protection system becomes more resilient. Test results were compared to hydrodynamics simulation results by using FLOW3D. The results revealed that the erosion resistance of levees can be substantially reduced by providing protective structures at the surface of the flood walls. An effectively designed protective structure could reduce the erosion depth as much as 40% and extend the erosion time as much as 400%.
- 1 August 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (8) , 731-742
Evaluation of a T-Wall Section in New Orleans Considering 3D Soil-Structure Interaction
T-walls in New Orleans survived Hurricane Katrina whereas I-walls obviously failed in several sections. However, it is still unclear whether these T-walls truly survived the hurricane with a fair amount of safety margins or barely survived it with undetected damages. The initial design of T-walls was based on simplified loading conditions with limited consideration of soil-structure interaction. In this study, three-dimensional (3D) numerical analyses were conducted, incorporating realistic loading conditions and soil-structure interactions but with time-saving techniques to evaluate the detailed behavior of T-walls. This paper addressed the procedure of innovative 3D numerical analyses and important findings by using special structural elements in FLAC3D. From this study, T-walls were found to have adequate stress levels in H-piles and concrete walls. However, it showed that the major factor that may cause the instability of the T-wall was the slope instability-type unbalanced force. This unbalanced forc...
- 1 August 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (8) , 731-742
Evaluation of a T-Wall Section in New Orleans Considering 3D Soil-Structure Interaction
T-walls in New Orleans survived Hurricane Katrina whereas I-walls obviously failed in several sections. However, it is still unclear whether these T-walls truly survived the hurricane with a fair amount of safety margins or barely survived it with undetected damages. The initial design of T-walls was based on simplified loading conditions with limited consideration of soil-structure interaction. In this study, three-dimensional (3D) numerical analyses were conducted, incorporating realistic loading conditions and soil-structure interactions but with time-saving techniques to evaluate the detailed behavior of T-walls. This paper addressed the procedure of innovative 3D numerical analyses and important findings by using special structural elements in FLAC3D. From this study, T-walls were found to have adequate stress levels in H-piles and concrete walls. However, it showed that the major factor that may cause the instability of the T-wall was the slope instability-type unbalanced force. This unbalanced forc...
- 1 April 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (4) , 398-404
Erosion Study of New Orleans Levee Materials Subjected to Plunging Water
During Hurricane Katrina, overtopping water caused erosion and subsequent failure of several sections of I-type flood walls in New Orleans. Erosion stemmed from the kinetic energy of water falling from the top of the flood wall, unlike the typical surface erosion caused by shear flow. This study evaluated the effects of important parameters of levee soils—fines content, degree of compaction (DOC), clay mineralogy, and water content in relation to the erosion behavior of New Orleans levees subjected to the plunging water. In general, test results showed that a higher fines content contributed to greater erosion resistance. The trend became unclear when fines content exceeded 20–25%. A higher degree of compaction did not necessarily contribute to greater erosion resistance. Underwater soaked soils showed much less erosion resistance than nonsoaked soils. Soils containing expansive clay minerals showed less erosion resistance than soils containing nonexpansive clay minerals.
- 1 April 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (4) , 398-404
Erosion Study of New Orleans Levee Materials Subjected to Plunging Water
During Hurricane Katrina, overtopping water caused erosion and subsequent failure of several sections of I-type flood walls in New Orleans. Erosion stemmed from the kinetic energy of water falling from the top of the flood wall, unlike the typical surface erosion caused by shear flow. This study evaluated the effects of important parameters of levee soils—fines content, degree of compaction (DOC), clay mineralogy, and water content in relation to the erosion behavior of New Orleans levees subjected to the plunging water. In general, test results showed that a higher fines content contributed to greater erosion resistance. The trend became unclear when fines content exceeded 20–25%. A higher degree of compaction did not necessarily contribute to greater erosion resistance. Underwater soaked soils showed much less erosion resistance than nonsoaked soils. Soils containing expansive clay minerals showed less erosion resistance than soils containing nonexpansive clay minerals.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 332-339
Determination of Soil Characteristic Frequency Using Acoustic Techniques
Based on the Biot's frequency dependent elastic wave propagation theory. The characteristic frequency of sandy soils is measured. In order to determine the characteristic frequency an inverse quality factor (1/Q) versus frequency sweep curve is used. In this paper, to compute the inverse quality factor two different techniques are adopted. The first technique utilizes the continuously supplied sinusoidal wave with different frequencies and measurements were made at two receivers which have different distances from the source. From the difference of amplitudes of two receivers the attenuation was computed. The second technique utilizes the free vibration decay curve to compute the attenuation. The characteristic frequency is clearly observed in this study from the 500 Hz to 4000 Hz frequency ranges. Furthermore, the response of two different techniques shows approximately the same results.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 332-339
Determination of Soil Characteristic Frequency Using Acoustic Techniques
Based on the Biot's frequency dependent elastic wave propagation theory. The characteristic frequency of sandy soils is measured. In order to determine the characteristic frequency an inverse quality factor (1/Q) versus frequency sweep curve is used. In this paper, to compute the inverse quality factor two different techniques are adopted. The first technique utilizes the continuously supplied sinusoidal wave with different frequencies and measurements were made at two receivers which have different distances from the source. From the difference of amplitudes of two receivers the attenuation was computed. The second technique utilizes the free vibration decay curve to compute the attenuation. The characteristic frequency is clearly observed in this study from the 500 Hz to 4000 Hz frequency ranges. Furthermore, the response of two different techniques shows approximately the same results.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1012-1019
Effects of Force Field in Molecular Mechanics Simulation of Geo-Materials
Molecular mechanics simulation of geo-materials provides enhanced understanding of fine details of material properties down to nano- or sub nano- scales. The molecular mechanics simulation of geo-materials however, is based on the non-deterministic mechanics due to the fact that the position and time of the electrons are not known simultaneously — so called Einstein's principle of uncertainty. To address this uncertainty, several (empirical) force fields are proposed. Each force field has a unique background and assumptions, and consequently presents different computational results. This study investigated the effects of different force fields (COMPASS, CVFF, PCFF, and Universal) on the predicted elastic properties of quartz sand grains.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1012-1019
Effects of Force Field in Molecular Mechanics Simulation of Geo-Materials
Molecular mechanics simulation of geo-materials provides enhanced understanding of fine details of material properties down to nano- or sub nano- scales. The molecular mechanics simulation of geo-materials however, is based on the non-deterministic mechanics due to the fact that the position and time of the electrons are not known simultaneously — so called Einstein's principle of uncertainty. To address this uncertainty, several (empirical) force fields are proposed. Each force field has a unique background and assumptions, and consequently presents different computational results. This study investigated the effects of different force fields (COMPASS, CVFF, PCFF, and Universal) on the predicted elastic properties of quartz sand grains.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 998-1005
Cell Size Effects in Characterizing Dry Quartz Sand Particles
Only a limited number of atoms is generally used in molecular mechanics analysis to reduce the computation time, which will be exhaustive otherwise. This paper analyzed the cell size effects in characterizing fundamental properties of a dry quartz grain using molecular mechanics. In order to find the minimum number of atoms that produces the representative material properties, this study performed the numerical analysis for different cell sizes. This study also analyzed the cell size effects in particulate mechanics simulations which essentially characterize the assemblage properties of quartz sand grains. From this research, it turned out that four times the unit cell size is required as a cell size to obtain representative properties of a quartz grain in molecular mechanics simulation. It also turned out that about ten times the grain size is required as a cell size to obtain representative properties of a quartz sands assemblage.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 998-1005
Cell Size Effects in Characterizing Dry Quartz Sand Particles
Only a limited number of atoms is generally used in molecular mechanics analysis to reduce the computation time, which will be exhaustive otherwise. This paper analyzed the cell size effects in characterizing fundamental properties of a dry quartz grain using molecular mechanics. In order to find the minimum number of atoms that produces the representative material properties, this study performed the numerical analysis for different cell sizes. This study also analyzed the cell size effects in particulate mechanics simulations which essentially characterize the assemblage properties of quartz sand grains. From this research, it turned out that four times the unit cell size is required as a cell size to obtain representative properties of a quartz grain in molecular mechanics simulation. It also turned out that about ten times the grain size is required as a cell size to obtain representative properties of a quartz sands assemblage.