Kadir Karakus
Kadir Karakus has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Fatih Mengeloglu
Department of Forest Industry Engineering, Kahramanmaras Sutcuimam University, Kahramanmaras, Turkey
1 shared publication Fatih Mengeloğlu
1 shared publication
Latest Publications
- 23 November 2015
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 15 (2)
TERMOPLAST?K N??ASTA ESASLI POL?MER-KOMPOZ?T KÖPÜK ÜRET?M?
Öz Bu çalışmada, termoplastik nişasta içerisine dolgu maddesi olarak buğday sapı unları ve polimer matris olarak biyobozunur polikaprolakton (PCL) kullanılarak polimer kompozit malzemeler üretilmiştir. Polimer kompozit malzemelerinin üretimi ekstrüzyon ve pres kalıplama yöntemi ile gerçekleştirilmiştir. Üretilen kompozit örnekleri mikro-hücre yöntemi teknolojisi kullanılarak köpüklendirme işlemine tabi tutulmuştur. Köpüklendirilmiş örneklerin yoğunlukları tespit edilmiş olup taramalı elektron mikroskobu yardımıyla (SEM) morfolojik özellikleri belirlenmiştir. Köpüklendirme işleminden önce kompozit örneklerin gaz tutma ve gaz çıkış hızı değerleri belirlenmiştir. Sonuçlar incelendiğinde PCL oranındaki artışa bağlı olarak örneklerin gaz tutma kapasitesinde önemli oranda bir artış, gaz çıkış hızı değerlerinde ise PCL oranındaki artışa paralel olarak bir azalma meydana gelmiştir. PCL oranındaki artışa paralel olarak köpüklendirmenin daha iyi olduğu ve düşük yoğunluklu örneklerin üretilebildiği tespit edilmiştir.
- 23 November 2015
- Published by Kastamonu University in Kastamonu University Journal of Forestry Faculty
- Vol. 15 (2)
TERMOPLAST?K N??ASTA ESASLI POL?MER-KOMPOZ?T KÖPÜK ÜRET?M?
Öz Bu çalışmada, termoplastik nişasta içerisine dolgu maddesi olarak buğday sapı unları ve polimer matris olarak biyobozunur polikaprolakton (PCL) kullanılarak polimer kompozit malzemeler üretilmiştir. Polimer kompozit malzemelerinin üretimi ekstrüzyon ve pres kalıplama yöntemi ile gerçekleştirilmiştir. Üretilen kompozit örnekleri mikro-hücre yöntemi teknolojisi kullanılarak köpüklendirme işlemine tabi tutulmuştur. Köpüklendirilmiş örneklerin yoğunlukları tespit edilmiş olup taramalı elektron mikroskobu yardımıyla (SEM) morfolojik özellikleri belirlenmiştir. Köpüklendirme işleminden önce kompozit örneklerin gaz tutma ve gaz çıkış hızı değerleri belirlenmiştir. Sonuçlar incelendiğinde PCL oranındaki artışa bağlı olarak örneklerin gaz tutma kapasitesinde önemli oranda bir artış, gaz çıkış hızı değerlerinde ise PCL oranındaki artışa paralel olarak bir azalma meydana gelmiştir. PCL oranındaki artışa paralel olarak köpüklendirmenin daha iyi olduğu ve düşük yoğunluklu örneklerin üretilebildiği tespit edilmiştir.
- Open Access
Thermal Degradation, Mechanical Properties and Morphology of Wheat Straw Flour Filled Recycled Thermoplastic Composites
Thermal behaviors of wheat straw flour (WF) filled thermoplastic compositeswere measured applying the thermogravimetric analysis and differential scanningcalorimetry. Morphology and mechanical properties were also studied using scanningelectron microscope and universal testing machine, respectively. Presence of WF inthermoplastic matrix reduced the degradation temperature of the composites. One for WFand one for thermoplastics, two main decomposition peaks were observed. Morphologicalstudy showed that addition of coupling agent improved the compatibility between WFs andthermoplastic. WFs were embedded into the thermoplastic matrix indicating improvedadhesion. However, the bonding was not perfect because some debonding can also be seenon the interface of WFs and thermoplastic matrix. In the case of mechanical properties ofWF filled recycled thermoplastic, HDPE and PP based composites provided similar tensileand flexural properties. The addition of coupling agents improved the properties ofthermoplastic composites. MAPE coupling agents performed better in HDPE while MAPPcoupling agents were superior in PP based composites. The composites produced with thecombination of 50-percent mixture of recycled HDPE and PP performed similar with theuse of both coupling agents. All produced composites provided flexural properties requiredby the ASTM standard for polyolefin-based plastic lumber decking boards.
Open AccessThermal Degradation, Mechanical Properties and Morphology of Wheat Straw Flour Filled Recycled Thermoplastic Composites
Thermal behaviors of wheat straw flour (WF) filled thermoplastic compositeswere measured applying the thermogravimetric analysis and differential scanningcalorimetry. Morphology and mechanical properties were also studied using scanningelectron microscope and universal testing machine, respectively. Presence of WF inthermoplastic matrix reduced the degradation temperature of the composites. One for WFand one for thermoplastics, two main decomposition peaks were observed. Morphologicalstudy showed that addition of coupling agent improved the compatibility between WFs andthermoplastic. WFs were embedded into the thermoplastic matrix indicating improvedadhesion. However, the bonding was not perfect because some debonding can also be seenon the interface of WFs and thermoplastic matrix. In the case of mechanical properties ofWF filled recycled thermoplastic, HDPE and PP based composites provided similar tensileand flexural properties. The addition of coupling agents improved the properties ofthermoplastic composites. MAPE coupling agents performed better in HDPE while MAPPcoupling agents were superior in PP based composites. The composites produced with thecombination of 50-percent mixture of recycled HDPE and PP performed similar with theuse of both coupling agents. All produced composites provided flexural properties requiredby the ASTM standard for polyolefin-based plastic lumber decking boards.