Fatih Mengeloglu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Wood Ash and Microcrystalline Cellulose (MCC) Filled Unsaturated Polyester Composites

    by Kadir Karakus, İlkay Atar, İbarahim Halil Başboğa, Fatma Bozkurt, Fatih Mengeloğlu

    En tr Abstract Aim of study: The objectives this research was determined the effects of wood ash and microcrystalline cellulose ( MCC) filler on density and tensile, flexural and impact properties in the unsaturated polyester based composites. Area of study: To determine the some properties of polyester based composites manufactured using different filler. Material and Methods: In this study, polyester based composites were produced using wood ash and MCC as reinforcement agent. Polyester based composites were manufactured by casting method. During manufacturing process, cobalt and methyl ethyl ketone peroxide (MEKP) were used as accelerator and catalyser, respectively. Main results: Wood ash provided better tensile strength compare to the MCC ones. Best tensile strength and elongation at break values were achieved with the use of 5% wood ash. In contrast, best tensile modulus results were obtained when MCC was utilized. In the case of flexural properties, both flexural strength and flexural modulus were reduced with the reinforcing agent concentration increase regardless of reinforcements type. Research highlights: Density was increased with rising filler concentrations. Özet Çalışmanın amacı: Doymamış polyester esaslı kompozit malzemelerin yoğunluk, çekme, eğilme ve darbe direnci özellikleri üzerine odun külü ve mikrokristalin selüloz oranının etkisinin belirlenmesi amaçlanmıştır.            Çalışma alanı: Poliester esaslı kompozitlerde farklı dolgu maddeleri kullanılarak bazı özelliklerinin belirlenmesidir. Materyal ve Yöntem: Bu çalışmada polimerik matris olarak doymamış poliester reçinesi kullanılırken dolgu maddesi olarak odun külü ve mikrokristalin selüloz kullanılmıştır. Poliester reçinesi esaslı kompozitler kast yöntemiyle üretilmiştir. Poliester reçinesi içerisine kobalt ve sertleştirici olarak Metil Etil Keton Peroksit (MEKP) ilave edilerek jel kıvamında olacak şekilde matris karışımı oluşturulmuştur. Sonuçlar: Odun külü katılarak üretilen poliester reçinesi esaslı kompozitlerin çekme direnci değerleri mikrokristalin selüloz içeren kompozitlere göre daha iyi sonuçlar verdiği tespit edilmiştir. En iyi çekme direnci ve kopmada uzama değerinin %5 odun külü içeren kompozitlere ait olduğu belirlenmiştir. Çekmede elastikiyet modülünde ise en iyi sonucun mikrokristalin selüloz içeren kompozitlere ait olduğu görülmüştür. Odun külü ve mikrokristalin selüloz oranın artmasıyla kompozitlerin eğilme direnci ve eğilmede elastikiyet modülü değerlerinin azaldığı belirlenmiştir. Araştırma vurguları: Dolgu maddesi oranın artmasıyla üretilen kompozitlerin yoğunluklarının arttığı tespit edilmiştir.


  • Utilization of Recycled PET Flours in Recycled Polyvinyl Chloride (PVC) Composites

    by Ilkay Atar, Kadir Karakuş, İbrahim Halil Başboğa, Fatma Bozkurt, Fatih Mengeloğlu

    Recycling is vital subject for sustainable future and environment. Plastic waste can be post-consumer and pre-consumer and need urgent recycling. Both PVC and Polyethylene terephthalate (PET) were used commonly and has important place in solid waste stream. These polymers should be reused or recycled instead of landfilling due to their valuable properties. In this study, potential utilization of PET flour in recycled PVC composites was investigated using 2-level factorial design. Processing type (injection molding vs compression molding) and PET filling concentration (0% and 10%) during recycled PVC composite materials manufacturing were studied. During manufacturing process, 20 phr (per-hundred-resin) DOP was utilized. Density, tensile, flexural, impact and hardness (shore D) properties of composites were determined. Results showed that samples produced with injection molding process provided superior tensile properties compared to compression molding process ones. Addition of PET flour into recycled PVC matrix both reduced the tensile strength and elongation at break values while improving tensile modulus. In the case of flexural properties, compression molding and injection molding provided higher flexural strength and flexural modulus, respectively. Impact strength was reduced with injection molding and PET presence in the matrix. Processing type did not affect the hardness of the materials. However, addition of PET in the PVC matrix increased the hardness of the samples. Future studies will be conducted to investigate the effect of using different size and shape PET fibers in recycled PVC.

  • Effects of Processing Methods, DOP Amount and Filler Content on the Mechanical Properties of Recycled Polyvinyl Chloride (PVC) Composites

    by İbrahim Halil Başboğa, Kadir Karakuş, İlkay Atar, Fatma Bozkurt, Fatih Mengeloğlu

    PVC is one of the most commercialized thermoplastic materials with industrial and household applications. Plastic possesses an important percentage in waste stream and its recycling is vital. Plasticizer usage is also essential for the PVC manufacturing and recycling. It is the purpose of this study to determine the effects of processing methods, DOP concentration and wood flour amount on the mechanical properties of recycled PVC composites. 15 and 30 phr (per-hundred-resin) DOP and 0-15-30 phr wood flour was studied. Composite materials were produced using injection and compression molding methods. Tensile, flexural, impact, hardness (shore D) and density of the composites were determined. Based on these results, DOP and filler content and process had a significant effect on mechanical properties. Utilization of DOP in the PVC matrix made material softer and flexible. Resulting materials had higher elongation at break and impact strength and smaller shore D values. In an expense to these good results, it reduced the tensile and flexural strength and modulus values. Addition of wood filler in the system, increased modulus values while reducing strength values. In the case of processing methods, injection molded samples provided overall better properties than compression molded ones. It should be noted that, in the case of injection molding, samples were better mixed due to the screw in the machine. Recycling of PVC is a vital subject and more study is needed.

  • Open Access

    KAYIN VE KAVAK KAPLAMALARIN MELAMİN FORMALDEHİT TUTKALI KULLANILARAK LAMİNE KAPLAMA KERESTE ÜRETİMİNE UYGUNLUĞU

    by İlkay Atar, İbrahim Halil Başboğa, Kadir Karakuş, Fatih Mengeloğlu

    Lamine kaplama kereste (LVL) inşaat yapılarında kiriş, döşeme kirişi, başlıklar ve paneller gibi çerçeve üyeleri olarak etkili ve kullanışlı olduğunu ispatlamıştır. LVL’nin türkiyede uygulaması ve üretimi sınırlıdır. Bu çalışmada biçilmiş kayın ve kavak kaplamaları, melamin formaldehit (MF) tutkalı kullanılarak dört farklı tipte yedi tabakalı LVL’ler üretilmiştir. LVL’ler her dış tabaka için iki adet kaplama ve iç tabaka için üç adet kaplama olacak şekilde oluşturuldu. Üretilen LVL’ler kaplamaların kullanım yeri ve türüne bağlı olarak kodlandırıldı. BBBBBBB, BBPPPBB, PPPPPPP ve PPBBBPP sırasıyla I.grup, II. Grup, III. Grup ve IV. Grup olarak isimlendirildi. Fiziksel özellikler olarak fırın Kurusu özgül ağırlık ve rutubet değerleri TS 2472 (1976a) ve TS 2471 (1976b) standartlarına göre belirlendi. Yapışma mukavemeti, eğilme direnci, eğilmede elastikiyet modülü ve liflere paralel basınç direnci gibi mekanik özellikler sırasıyla EN 314-1 (2004), EN310 (1993) ve TS 2595 (1977) standartlarına göre belirlendi. Bu çalışmada en yüksek direnç ve yoğunluk değeri tamamı kayın kaplamalarından üretilen I. Grup LVL’lerde elde edildi. Diğer yandan en düşük değerler tamamı kavak kaplamalarından üretilen III. Grup LVL’lerde gözlemlendi. Kayın kaplamalarının LVL’ ye katılım oranının direnç ve yoğunluk değerlerinde bir artış sağladığı söylenebilir.


  • Open Access

    Some Properties of Composite Panels Made from Wood Flour and Recycled Polyethylene

    by Turgay Ozdemir, Fatih Mengeloglu

    This study investigated the effect of board type (unmodified vs. MAPE modified) on the surface quality and thickness swelling-water absorption properties of recycled high density polyethylene (HDPE) based wood plastic composites. Additionally, two commercially available coatings (cellulosic coating and polyurethane lacquer coating) were also applied to composite surfaces and their adhesion strength, abrasion and scratch resistance, and gloss values were determined. This study showed that modification of the composites with MAPE coupling agent increased the surface smoothness and reduced the water absorption and thickness swelling of the panels. Abrasion resistance of the composites was also improved through MAPE modification. Regardless of board type, higher scratch resistance and gloss values were observed for polyurethane lacquer coated samples compared to those of cellulosic varnish coated ones. Improvement of adhesion strength was also seen on SEM micrographs.


  • Open Access

    Determination of Thermal Properties and Morphology of Eucalyptus Wood Residue Filled High Density Polyethylene Composites

    by Fatih Mengeloglu, Ayse Kabakci

    Thermal behaviors of eucalyptus wood residue (EWR) filled recycled high density polyethylene (HDPE) composites have been measured applying the thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Morphology of the materials was also studied using scanning electron microscope (SEM). Addition of the EWR into the recycled HDPE matrix reduced the starting of degradation temperature. EWR filled recycled HDPE had two main decomposition peaks, one for EWR around 350 °C and one for recycled HDPE around 460 °C. Addition of EWR did not affect the melting temperature of the recycled HDPE. Morphological study showed that addition of coupling agent improved the compatibility between wood residue and recycled HDPE.


  • Open Access

    Thermal Degradation, Mechanical Properties and Morphology of Wheat Straw Flour Filled Recycled Thermoplastic Composites

    by Fatih Mengeloglu, Kadir Karakus

    Thermal behaviors of wheat straw flour (WF) filled thermoplastic compositeswere measured applying the thermogravimetric analysis and differential scanningcalorimetry. Morphology and mechanical properties were also studied using scanningelectron microscope and universal testing machine, respectively. Presence of WF inthermoplastic matrix reduced the degradation temperature of the composites. One for WFand one for thermoplastics, two main decomposition peaks were observed. Morphologicalstudy showed that addition of coupling agent improved the compatibility between WFs andthermoplastic. WFs were embedded into the thermoplastic matrix indicating improvedadhesion. However, the bonding was not perfect because some debonding can also be seenon the interface of WFs and thermoplastic matrix. In the case of mechanical properties ofWF filled recycled thermoplastic, HDPE and PP based composites provided similar tensileand flexural properties. The addition of coupling agents improved the properties ofthermoplastic composites. MAPE coupling agents performed better in HDPE while MAPPcoupling agents were superior in PP based composites. The composites produced with thecombination of 50-percent mixture of recycled HDPE and PP performed similar with theuse of both coupling agents. All produced composites provided flexural properties requiredby the ASTM standard for polyolefin-based plastic lumber decking boards.