Alexander I. Tyurin

Three titanium alloys with 0.5, 6, and 9 wt.% iron were investigated, and the samples were pre-annealed in three different regions of the Ti–Fe phase diagram, namely β, α+β, and α+FeTi. After annealing, five samples of different phases and structural compositions were studied. They were then subjected to the high-pressure torsion (HPT). The microstructure of the samples before and after HPT treatment was studied using transmission and scanning electron microscopy. The microstructure of the samples obtained during heat treatment before HPT treatment had a fundamental effect on the microstructure after HPT. Grain boundary layers and chains of particles formed during the annealing process made it difficult to mix the material during HPT, which led to the formation of areas with non-uniform mixing of components. Thus, the grain boundary layers of the α-phase formed in the Ti–6wt % Fe alloy after annealing at 670 °C significantly decreased the mixing of the components during HPT. Despite the fact that the microstructure and phase composition of Ti–6wt % Fe alloys pre-annealed in three different regions of the Ti–Fe phase diagram had significant differences, after HPT treatment, the phase compositions of the studied samples were quite similar. Moreover, the measured micro- and nanohardness as well as the Young’s modulus of Ti–6wt % Fe alloy had similar values. It was shown that the microhardness of the studied samples increased with the iron content. The values of nanohardness and Young’s modulus correlated well with the fractions of β- and ω-phases in the studied alloys.

The study focused on a 21.99 at.%Ti–22.49 at.%Zr–20.35 at.%Hf–17.45 at.%Mo–17.73 at.%Cr). Analytical techniques such as X-ray diffraction, scanning electron microscopy as well as X-ray absorption spectroscopy were employed to investigate the alloy’s structure, phase transformations, and properties. The alloy in the as-cast state contained three phases, namely the body-centred cubic (A2) phase, hexagonal Laves phase (C14), and cubic Laves phase (C15). The alloy has been annealed for a long time at different temperatures. It led to the disappearance of the hexagonal Laves phase, leaving behind two primary phases, namely the cubic Laves phase (C15) and the body-centered cubic phase (A2). At 1200 °C, the A2 phase almost disappeared, resulting in a practically single-phase sample. After a high-pressure torsion (HPT) treatment, the hexagonal Laves phase disappeared entirely, while the A2 and C15 phases remained. The grain size of the A2 and C15 phases was refined after HPT and grains were elongated, and their configuration resembled a layered structure. The high hardness of the A2 and C15 + C14 phases accounted for this behavior. The lattice parameters in the A2 and C15 phases after HPT treatment approached those observed after prolonged annealing at 1000 °C, indicating that the composition of these phases after short-term high-pressure torsion at ambient temperature is equivalent to the composition of these phases after long tempering at 1000 °C. The rate of diffusion-like mass transfer during severe plastic deformation was estimated to be many orders of magnitude higher than that for conventional bulk diffusion at the HPT treatment temperature and similar to that at elevated temperatures above 1000 °C. X-ray absorption spectroscopy results obtained at K-edges of Ti, Cr, Zr, and Mo as well as at the L3-edge of Hf indicated that the local environment around metal atoms before HPT was similar to that after HPT. However, the static disorder increased after HPT, which could be attributed to an increased specific amount of metal atoms in the disordered grain boundary layers after HPT-driven grain refinement.

A Zr-doped CaO sorbent for high-temperature CO₂ capture was fabricated using electrospinning. The nanofiber sorbent with an average filament diameter of about 160 nm is characterized by an initial CO₂ uptake capacity of 12.1 mmol/g, a specific surface area of 79 m²/g, an indentation Young’s modulus of 520 MPa, and a hardness of 1.6 MPa. After 50 carbonation/decarbonation cycles, the sorbent has a decent CO₂ uptake capacity of 9.7 mmol/g due to the uniform distribution of CaZrO₃ in the CaO nanofibers to prevent CaO grain growth caused by CaCO₃ sintering. It is revealed that the sorbent CO₂ uptake capacity decreases both with an increase in the decarbonation temperature and with an increase in the CO₂ concentration in the gas flow upon carbonation, where the sorbent CO₂ uptake capacity is more sensitive to the decarbonation temperature than to the CO₂ concentration in the gaseous stream during carbonation. It is assumed that the electrospun regenerable Zr-doped CaO sorbent is effective for removing CO₂ from flue gases.

In this work the high-entropy alloy studied contained six components, Ti/Zr/Hf/Mo/Cr/Co, and three phases, namely one phase with body-centered cubic lattice (BCC) and two Laves phases C14 and C15. A series of annealings in the temperature range from 600 to 1000 °C demonstrated not only a change in the microstructure of the TiZrHfMoCrCo alloy, but also the modification of phase composition. After annealing at 1000 °C the BCC phase almost fully disappeared. The annealing at 600 and 800 °C leads to the formation of new Laves phases. After high-pressure torsion (HPT) of the as-cast TiZrHfMoCrCo alloy, the grains become very small, the BCC phase prevails, and C14 Laves phase completely disappears. This state is similar to the state after annealing at high effective temperature T_eff. The additional annealing at 1000 °C after HPT returns the phase composition back to the state similar to that of the as-cast alloy after annealing at 1000 °C. At 1000 °C the BCC phase completely wets the C15/C15 grain boundaries (GBs). At 600 and 800 °C the GB wetting is incomplete. The big spread of nanohardness and Young’s modulus for the BCC phase and (C15 + C14) Laves phases is observed.

The paper analyzes the effect of severe plastic deformation by the high-pressure torsion (HPT) on phase transformations, in particular, on the formation of the ω-phase, and on mechanical properties, such as hardness and Young’s modulus, in Ti alloys with 1.5 and 15 wt.% Mo. Both alloys were pre-annealed at 1000 °C for 24 h and quenched. The microstructure of the initial Ti–1.5 wt.% Mo alloy consisted of the α-phase and α’-martensite, and the initial Ti–15 wt.% Mo alloy contained polycrystalline β solid solution. The hardness tests of the samples were carried out under the load of 10 and 200 mN. The annealed alloys were subjected to HPT, and the micro- and nanohardness of both deformed samples increased up to ~1 GPa compared to their initial state. It turned out that the values of hardness (H) and Young’s modulus (E) depend on the applied load on the indenter: the higher the applied load, the lower H and higher E. It was also found that the HPT leads to the 30% increase in E for an alloy with 1.5 wt.% Mo and to the 9% decrease in E for the alloy with 15 wt.% Mo. Such a difference in the behavior of the Young’s modulus is associated with phase transformations caused by the HPT.

The paper presents the results of creep measurement in common pine wood at different scales ranging from nano to macro by means of continuous naation. It is shown that wood structure elements pertaining to different scale levels make different contribution to steady creep rate. Keywords: naation, wood, creep.

The nanofibrous CaO sorbent for high-temperature CO₂ capture was fabricated by the calcination of electrospun composite filaments containing calcium acetylacetonate and polyacrylonitrile as a calcium-oxide precursor and a binder polymer, respectively. The calcination was carried out in air to prevent PAN carbonization and to obtain pure CaO nanofibers. The resulting mats of CaO nanofibers with the average diameter of 130 nm were characterized by a specific surface area of 31 m²/g, a CO₂-uptake capacity of 16.4 mmol/g at the carbonation temperature of 618 °C, a hardness of 1.87 MPa, and the indentation Young’s modulus of 786 MPa. The low decarbonation temperature makes the fabricated sorbent promising, for example, for the calcium-looping technology of CO₂ removal from the hot exhaust gases of fossil-fueled power plants.

The paper presents the results of mechanical properties scanning by means of naation across the annual growth rings of deciduous trees wood, small-leaved lime (Tilia cordata) and common oak (Quercus robur) in particular. Significant variations in microhardness H and Young's modulus E radial dependencies have been found for any of the studied species. Results can be useful 1) to amend the understanding the nature of macromechanical properties of various wood species and to reveal the details of their formation depending upon microstructural characteristics, 2) to optimize the technologies of growing, reinforcement and subsequent usage of the wood, 3) to develop new independent methods in dendrochronology and dendroclimatology Keywords: nanocomposites, naation, nano-/microhardness and Young's modulus scanning, tree annual growth rings, dendrochronology